ApiDocs::Service#to_xml has approx 11 statements Open
def to_xml(options = {})
- Read upRead up
- Exclude checks
A method with Too Many Statements
is any method that has a large number of lines.
Too Many Statements
warns about any method that has more than 5 statements. Reek's smell detector for Too Many Statements
counts +1 for every simple statement in a method and +1 for every statement within a control structure (if
, else
, case
, when
, for
, while
, until
, begin
, rescue
) but it doesn't count the control structure itself.
So the following method would score +6 in Reek's statement-counting algorithm:
def parse(arg, argv, &error)
if !(val = arg) and (argv.empty? or /\A-/ =~ (val = argv[0]))
return nil, block, nil # +1
end
opt = (val = parse_arg(val, &error))[1] # +2
val = conv_arg(*val) # +3
if opt and !arg
argv.shift # +4
else
val[0] = nil # +5
end
val # +6
end
(You might argue that the two assigments within the first @if@ should count as statements, and that perhaps the nested assignment should count as +2.)
ApiDocs::Service assumes too much for instance variable '@send_notification' Open
class ApiDocs::Service < ApplicationRecord
- Read upRead up
- Exclude checks
Classes should not assume that instance variables are set or present outside of the current class definition.
Good:
class Foo
def initialize
@bar = :foo
end
def foo?
@bar == :foo
end
end
Good as well:
class Foo
def foo?
bar == :foo
end
def bar
@bar ||= :foo
end
end
Bad:
class Foo
def go_foo!
@bar = :foo
end
def foo?
@bar == :foo
end
end
Example
Running Reek on:
class Dummy
def test
@ivar
end
end
would report:
[1]:InstanceVariableAssumption: Dummy assumes too much for instance variable @ivar
Note that this example would trigger this smell warning as well:
class Parent
def initialize(omg)
@omg = omg
end
end
class Child < Parent
def foo
@omg
end
end
The way to address the smell warning is that you should create an attr_reader
to use @omg
in the subclass and not access @omg
directly like this:
class Parent
attr_reader :omg
def initialize(omg)
@omg = omg
end
end
class Child < Parent
def foo
omg
end
end
Directly accessing instance variables is considered a smell because it breaks encapsulation and makes it harder to reason about code.
If you don't want to expose those methods as public API just make them private like this:
class Parent
def initialize(omg)
@omg = omg
end
private
attr_reader :omg
end
class Child < Parent
def foo
omg
end
end
Current Support in Reek
An instance variable must:
- be set in the constructor
- or be accessed through a method with lazy initialization / memoization.
If not, Instance Variable Assumption will be reported.
Similar blocks of code found in 2 locations. Consider refactoring. Invalid
xml.id_ id
xml.system_name system_name
xml.name name
xml.description description
xml.published published
- Read upRead up
Duplicated Code
Duplicated code can lead to software that is hard to understand and difficult to change. The Don't Repeat Yourself (DRY) principle states:
Every piece of knowledge must have a single, unambiguous, authoritative representation within a system.
When you violate DRY, bugs and maintenance problems are sure to follow. Duplicated code has a tendency to both continue to replicate and also to diverge (leaving bugs as two similar implementations differ in subtle ways).
Tuning
This issue has a mass of 25.
We set useful threshold defaults for the languages we support but you may want to adjust these settings based on your project guidelines.
The threshold configuration represents the minimum mass a code block must have to be analyzed for duplication. The lower the threshold, the more fine-grained the comparison.
If the engine is too easily reporting duplication, try raising the threshold. If you suspect that the engine isn't catching enough duplication, try lowering the threshold. The best setting tends to differ from language to language.
See codeclimate-duplication
's documentation for more information about tuning the mass threshold in your .codeclimate.yml
.
Refactorings
- Extract Method
- Extract Class
- Form Template Method
- Introduce Null Object
- Pull Up Method
- Pull Up Field
- Substitute Algorithm
Further Reading
- Don't Repeat Yourself on the C2 Wiki
- Duplicated Code on SourceMaking
- Refactoring: Improving the Design of Existing Code by Martin Fowler. Duplicated Code, p76