mibs/extreme/EXTREME-EAPS-MIB
-- ################################################################################
EXTREME-EAPS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY FROM SNMPv2-SMI
OBJECT-TYPE FROM SNMPv2-SMI
Unsigned32 FROM SNMPv2-SMI
TEXTUAL-CONVENTION FROM SNMPv2-TC
TruthValue FROM SNMPv2-TC
RowStatus FROM SNMPv2-TC
DisplayString FROM RFC1213-MIB
extremeAgent FROM EXTREME-BASE-MIB;
extremeEaps MODULE-IDENTITY
LAST-UPDATED "0502151530Z"
ORGANIZATION "Extreme Networks, Inc."
CONTACT-INFO "www.extremenetworks.com"
DESCRIPTION "Ethernet Automatic Protection Switching information."
::= { extremeAgent 18 }
EapsDomainMode
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Indicates the configured mode of an EAPS domain."
SYNTAX INTEGER { invalid (0),
master (1),
transit (2)
}
EapsMbrVlanType
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Indicates the type of vlan, whether it is control or
protected vlan, that is being added to the
EAPS domain."
SYNTAX INTEGER { unassigned (0),
control (1),
protected (2)
}
EapsRingPort
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "This represents an EAPS ring-port."
SYNTAX INTEGER (0..2147483647)
EapsPortType
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Indicates the ring port of the EAPS domains. The ring port
can be primary or secondary. This is used to specify which
port is being unconfigured."
SYNTAX INTEGER {
primary (1),
secondary (2)
}
EapsDomainState
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The operational state of an EAPS domain.
The states complete(1), failed(2), init(6), precomplete(7),
and preinit(8) apply only to domains configured as master.
The states linksup(3), linkdown(4) and preforwarding(5)
apply only to domains configured as transit.
The state init(0) applys to domains configured as either
master or transit."
SYNTAX INTEGER { idle (0),
complete (1),
failed (2),
linksup (3),
linkdown (4),
preforwarding (5),
init (6),
precomplete (7),
preinit (8)
}
EapsDomainPortStatus
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The operational state of an EAPS domain's ring-ports.
If the state is unknown (0), it indicates the domain is
still not up yet.
The valid states are up(1), down(2), blocked(3)."
SYNTAX INTEGER {
unknown (0),
up (1),
down (2),
blocked (3)
}
EapsFailTimerExpiryAction
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The action to take when the failed timer expires.
If action is configured to sendAlert(0), and the
fail expires, the Master will remain in Complete or Init
state, and a trap - extremeEapsFailTimerExpFlagSet - will
be sent.
When this fail timer stops expiring another trap -
extremeEapsFailTimerExpFlagClear - will be sent.
If the action is configured to openSecondaryPort(1), and
the fail timer expires, the Master's state will be set to
Failed, and it will open the secondary port."
SYNTAX INTEGER { sendAlert (0),
openSecondaryPort (1)
}
EapsSharedPortState
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The operational state of an EAPS Shared-Port instance.
The states are idle(0), ready(1), blocking(2), and
preforwarding(3)."
SYNTAX INTEGER { idle (0),
ready (1),
blocking (2),
preforwarding (3)
}
EapsSharedPortMode
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "If the mode is unconfigured(0), it indicates the EAPS
shared port's mode has yet to be configured.
The valid configured modes of an EAPS Shared-port are
controller(1) and partner(2)"
SYNTAX INTEGER {
unconfigured (0),
controller (1),
partner (2)
}
EapsSharedPortSegmentTimerExpiryAction
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The action to take when the EAPS Shared-port's segment
timer expires.
If action is configured to sendAlert(0), and the
segment timer expires, the segment's status will remain
in Up state, and a trap -
extremeEapsSegmentTimerExpFlagSet - will be sent.
When this segment timer stops expiring another trap -
extremeEapsSegmentTimerExpFlagClear - will be sent.
If the action is configured to segmentDown(1), and the
segment timer expires, the segment's status will be set to
Down."
SYNTAX INTEGER { sendAlert (0),
segmentDown (1)
}
EapsSharedPortNeighborStatus
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The operational status of an EAPS Shared-port's neighbor
reachabilty.
The states are neighborDown(0), neighborUp(1), and
neighborError(2)."
SYNTAX INTEGER { neighborDown (0),
neighborUp (1),
neighborError (2)
}
EapsSharedPortRootBlockerStatus
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The operational status of an EAPS Shared-port's Root-
Blocker.
The states are false(0), active(1), and inactive(2)."
SYNTAX INTEGER { false (0),
active (1),
inactive (2)
}
EapsSharedPortSegmentStatus
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The operational status of an EAPS Shared-port's segments.
The states are unknown(0), segUp(1), segDown(2),
segBlockingUp(3) and segBlockingDown(4)."
SYNTAX INTEGER { unknown (0),
segUp (1),
segDown (2),
segBlockingUp (3),
segBlockingDown (4)
}
EapsSharedPortVlanPortStatus
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "The operational status of an EAPS Shared-port's vlan-port.
The states are unknown(0), activeOpen(1), blocked(2),
open(3) and down(4)."
SYNTAX INTEGER { unknown (0),
activeOpen (1),
blocked (2),
open (3),
down (4)
}
EapsDomainPriority
::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Indicates the configured priority of an EAPS domain."
SYNTAX INTEGER { normal (0),
high (1)
}
extremeEapsTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeEapsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains EAPS information about all EAPS
domains on this device."
::= { extremeEaps 1 }
extremeEapsEntry OBJECT-TYPE
SYNTAX ExtremeEapsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An individual entry of this table contains EAPS
information related to that EAPS domain."
INDEX { extremeEapsName }
::= { extremeEapsTable 1 }
ExtremeEapsEntry ::= SEQUENCE {
extremeEapsName DisplayString,
extremeEapsMode EapsDomainMode,
extremeEapsState EapsDomainState,
extremeEapsFailedFlag TruthValue,
extremeEapsEnabled TruthValue,
extremeEapsPrimaryPort EapsRingPort,
extremeEapsSecondaryPort EapsRingPort,
extremeEapsHelloTimer INTEGER,
extremeEapsHelloTimerMs INTEGER,
extremeEapsFailedTimer INTEGER,
extremeEapsFailedTimerExpiryAction EapsFailTimerExpiryAction,
extremeEapsUnconfigRingPort EapsPortType,
extremeEapsPrimaryStatus EapsDomainPortStatus,
extremeEapsSecondaryStatus EapsDomainPortStatus,
extremeEapsProtectedVlansCount INTEGER,
extremeEapsPriority EapsDomainPriority,
extremeEapsRowStatus RowStatus
}
extremeEapsName OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The EAPS domain name."
::= { extremeEapsEntry 1 }
extremeEapsMode OBJECT-TYPE
SYNTAX EapsDomainMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This indicates the mode of the EAPS domain."
::= { extremeEapsEntry 2 }
extremeEapsState OBJECT-TYPE
SYNTAX EapsDomainState
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This indicates the current EAPS state of this EAPS
domain."
::= { extremeEapsEntry 3 }
extremeEapsFailedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This indicates the status of the failed flag.
If the failed timer expires while its expiry action is
configured to sendAlert, this failed flag is set.
It is then cleared when the failed timer stops expiring, or
the expiry action is configured to openSecondaryPort."
::= { extremeEapsEntry 4 }
extremeEapsEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This indicated if this domain has been enabled or not."
::= { extremeEapsEntry 5 }
extremeEapsPrimaryPort OBJECT-TYPE
SYNTAX EapsRingPort
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This indicates the EAPS domain's primary ring-port.
Value of 0 indicates the primary port is still not
configured"
::= { extremeEapsEntry 6 }
extremeEapsSecondaryPort OBJECT-TYPE
SYNTAX EapsRingPort
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This indicates the EAPS domain's secondary ring-port.
Value of 0 indicates the secondary port is still not
configured"
::= { extremeEapsEntry 7 }
extremeEapsHelloTimer OBJECT-TYPE
SYNTAX INTEGER (0..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This indicates the EAPS domain's hello timer's value
in seconds."
::= { extremeEapsEntry 8 }
extremeEapsFailedTimer OBJECT-TYPE
SYNTAX INTEGER (2..300)
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This indicates the EAPS domain's failed timer's value
in seconds."
::= { extremeEapsEntry 9 }
extremeEapsFailedTimerExpiryAction OBJECT-TYPE
SYNTAX EapsFailTimerExpiryAction
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This indicates the action taken by the domain when the
fail timer expires.
If the action is to sendAlert, then a SNMP trap -
extremeEapsFailTimerExpFlagSet - will be sent, and the
secondary port will continue to remain in blocking state.
If the action is to openSecondaryPort, then the secondary
port will open and be set to forwarding state."
::= { extremeEapsEntry 10 }
extremeEapsUnconfigRingPort OBJECT-TYPE
SYNTAX EapsPortType
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This specifies which EAPS domain port is being
unconfigured.
Value of 1, indicates unconfigure the primary port.
Value of 2, indicates unconfigure secondary port."
::= { extremeEapsEntry 11 }
extremeEapsPrimaryStatus OBJECT-TYPE
SYNTAX EapsDomainPortStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This indicates the status of the EAPS domain's primary
ring-port."
::= { extremeEapsEntry 12 }
extremeEapsSecondaryStatus OBJECT-TYPE
SYNTAX EapsDomainPortStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This indicates the status of the EAPS domain's secondary
ring-port."
::= { extremeEapsEntry 13 }
extremeEapsProtectedVlansCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This gives the count of the number of vlans that are
being protected by this EAPS domain."
::= { extremeEapsEntry 14 }
extremeEapsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "The status of this entry as per standard RowStatus
conventions."
::= { extremeEapsEntry 15 }
extremeEapsHelloTimerMs OBJECT-TYPE
SYNTAX INTEGER (100..900)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This indicates the milliseconds portion of the EAPS domain's hello timer value
in milliseconds."
::= { extremeEapsEntry 16 }
extremeEapsPriority OBJECT-TYPE
SYNTAX EapsDomainPriority
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This gives the priority of the domain. Used along with spatial re-use to prioritize
handling of domains during a topology change."
::= { extremeEapsEntry 17 }
extremeEapsPrevState OBJECT-TYPE
SYNTAX EapsDomainState
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION "This indicates the previous EAPS state of this EAPS
domain. Used in state change traps information."
::= { extremeEaps 2 }
extremeEapsGlobalInfo OBJECT IDENTIFIER
::= { extremeEaps 3 }
extremeEapsGlobalEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates if EAPS is enabled globally on the switch."
::= { extremeEapsGlobalInfo 1 }
extremeEapsGlobalFastConvergence OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates if Fast Convergence is enabled globally on the
switch."
::= { extremeEapsGlobalInfo 2 }
extremeEapsLastConfigurationChange OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the last time there was any change in
EAPS configuration on the switch."
::= { extremeEapsGlobalInfo 3 }
extremeEapsLastStatusChange OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the last time there was any change in
EAPS domain, EAPS port, shared port, or segment status on
the switch. Time changes for extremeEapsState,
extremeEapsSharedPortState, extremeEapsSharedPortSegmentStatus,
extremeEapsFailedFlag, extremeEapsPrimaryStatus,
extremeEapsSecondaryStatus, extremeEapsSharedPortNbrStatus,
extremeEapsSharedPortRootBlockerStatus,
extremeEapsSharedPortSegmentFlagFailed."
::= { extremeEapsGlobalInfo 4 }
extremeEapsStatusTrapCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the number of status traps sent out since the switch
booted. Status traps counted include
extremeEapsSharedPortStateChange
extremeEapsRootBlockerStatusChange
extremeEapsPortStatusChange
extremeEapsStateChange
extremeEapsFailTimerExpFlagSet
extremeEapsFailTimerExpFlagClear."
::= { extremeEapsGlobalInfo 5 }
extremeEapsGlobalMulticastAddRingPorts OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Ring ports are added to existing multicast groups for protected
vlans on a topology change event."
::= { extremeEapsGlobalInfo 6 }
extremeEapsGlobalMulticastSendIGMPQuery OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "IGMP Query is sent out on all protected vlans on a topology change
event."
::= { extremeEapsGlobalInfo 7 }
extremeEapsGlobalMulticastTempFlooding OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Temporary Multicast flooding occurs on all protected vlans on a
topology change event."
::= { extremeEapsGlobalInfo 8 }
extremeEapsGlobalMulticastTempFloodingDuration OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The duration at which temporary Multicast flooding will occur."
::= { extremeEapsGlobalInfo 9 }
extremeEapsMbrVlanTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeEapsMbrVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table contains the control and all protected vlans
added to each EAPS domain on this device.
There can be only 1 control vlan, while many
protected vlans added to a EAPS domain."
::= { extremeEaps 4 }
extremeEapsMbrVlanEntry OBJECT-TYPE
SYNTAX ExtremeEapsMbrVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An individual entry of this table correlates a EAPS
domain with a VLAN added to it and its type whether it is
control or protected."
INDEX { extremeEapsName,
extremeEapsMbrVlanName,
extremeEapsMbrVlanType
}
::= { extremeEapsMbrVlanTable 1 }
ExtremeEapsMbrVlanEntry ::= SEQUENCE {
extremeEapsMbrVlanName DisplayString,
extremeEapsMbrVlanType EapsMbrVlanType,
extremeEapsMbrVlanTag INTEGER,
extremeEapsMbrVlanRowStatus RowStatus
}
extremeEapsMbrVlanName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The member VLAN's name."
::= { extremeEapsMbrVlanEntry 1 }
extremeEapsMbrVlanType OBJECT-TYPE
SYNTAX EapsMbrVlanType
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The member VLAN's type whether it is control or
protected."
::= { extremeEapsMbrVlanEntry 2 }
extremeEapsMbrVlanTag OBJECT-TYPE
SYNTAX INTEGER (1..4095)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The member VLAN's Vlan Id tag."
::= { extremeEapsMbrVlanEntry 3 }
extremeEapsMbrVlanRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "The status of this entry as per standard RowStatus
conventions."
::= { extremeEapsMbrVlanEntry 4 }
extremeEapsSharedPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeEapsSharedPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table contains all EAPS shared ports configured
on this device."
::= { extremeEaps 5 }
extremeEapsSharedPortEntry OBJECT-TYPE
SYNTAX ExtremeEapsSharedPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An individual entry of this table describes the
configuration of an EAPS shared port."
INDEX { extremeEapsSharedPortIfIndex }
::= { extremeEapsSharedPortTable 1 }
ExtremeEapsSharedPortEntry ::= SEQUENCE {
extremeEapsSharedPortIfIndex EapsRingPort,
extremeEapsSharedPortMode EapsSharedPortMode,
extremeEapsSharedPortLinkId INTEGER,
extremeEapsSharedPortSegmentTimerExpiryAction EapsSharedPortSegmentTimerExpiryAction,
extremeEapsSharedPortState EapsSharedPortState,
extremeEapsSharedPortNbrStatus EapsSharedPortNeighborStatus,
extremeEapsSharedPortDomainsCount INTEGER,
extremeEapsSharedPortProtectedVlansCount INTEGER,
extremeEapsSharedPortRootBlockerStatus EapsSharedPortRootBlockerStatus,
extremeEapsSharedPortRootBlockerId INTEGER,
extremeEapsSharedPortRowStatus RowStatus,
extremeEapsSharedPortSegmentHealthInterval INTEGER,
extremeEapsSharedPortSegmentTimeout INTEGER,
extremeEapsSharedPortCommonPathFailedFlag TruthValue,
extremeEapsSharedPortCommonPathHealthInterval INTEGER,
extremeEapsSharedPortCommonPathTimeout INTEGER
}
extremeEapsSharedPortIfIndex OBJECT-TYPE
SYNTAX EapsRingPort
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The ifIndex of a port configured as an EAPS shared port."
::= { extremeEapsSharedPortEntry 1 }
extremeEapsSharedPortMode OBJECT-TYPE
SYNTAX EapsSharedPortMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION "The configured mode of the EAPS shared port."
::= { extremeEapsSharedPortEntry 2 }
extremeEapsSharedPortLinkId OBJECT-TYPE
SYNTAX INTEGER (0..65534)
MAX-ACCESS read-create
STATUS current
DESCRIPTION "The configured Link Id for the EAPS shared port.
Each common link in the entire network will be assigned a
unique link Id. Each shared-port instance on either end
of this common link will be configured with this
link Id.
Value of 0 indicates the link Id is still not configured."
::= { extremeEapsSharedPortEntry 3 }
extremeEapsSharedPortSegmentTimerExpiryAction OBJECT-TYPE
SYNTAX EapsSharedPortSegmentTimerExpiryAction
MAX-ACCESS read-create
STATUS current
DESCRIPTION "This indicates the action taken by the EAPS Shared port
instance when a segment timer expires.
If the action is sendAlert, then when the segment timer
expires, an SNMP trap will be sent, and the segment will
remain in Up state, with the failed flag set to True.
If the action is segmentDown, then when the timer expires,
the segment will be set to Down state."
::= { extremeEapsSharedPortEntry 4 }
extremeEapsSharedPortState OBJECT-TYPE
SYNTAX EapsSharedPortState
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This indicates the state of the EAPS Shared port instance.
The states can be idle(0), ready(1), blocking(2), and
preforwarding(3)."
::= { extremeEapsSharedPortEntry 5 }
extremeEapsSharedPortNbrStatus OBJECT-TYPE
SYNTAX EapsSharedPortNeighborStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This indicates the status of reachabilty to the neighbor
on the other end of the Shared-segment.
If the neighbor on the other end is reachable with
matching link-id and different modes, then the status is
NeighborUp.
If the neighbor is not reachable, this status is
NeighborDown.
If the neighbor is reachable, but with the same mode,
then this status is set to Error."
::= { extremeEapsSharedPortEntry 6 }
extremeEapsSharedPortDomainsCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This gives the count of the number of EAPS domains that
are sharing this shared-port."
::= { extremeEapsSharedPortEntry 7 }
extremeEapsSharedPortProtectedVlansCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This gives the count of the number of vlans that are
being protected by this shared-port instance."
::= { extremeEapsSharedPortEntry 8 }
extremeEapsSharedPortRootBlockerStatus OBJECT-TYPE
SYNTAX EapsSharedPortRootBlockerStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION "If this shared port instance is not in Root blocker state,
the status is False.
If the shared port is in Root blocker state, and its
path detect message is being returned to it, it is in
Active state.
If the shared port is in Root blocker state, but its
path detect message is not making it back to itself, then
its root blocker status is Inactive."
::= { extremeEapsSharedPortEntry 9 }
extremeEapsSharedPortRootBlockerId OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This is the Link Id of the Root Blocker in the entire
network.
If there is no root blocker in the network, this value
is 65535."
::= { extremeEapsSharedPortEntry 10 }
extremeEapsSharedPortRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION "The status of this entry as per standard RowStatus
conventions."
::= { extremeEapsSharedPortEntry 11 }
extremeEapsSharedPortSegmentHealthInterval OBJECT-TYPE
SYNTAX INTEGER (0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Interval at which health check PDUs are sent out each segment port."
::= { extremeEapsSharedPortEntry 12 }
extremeEapsSharedPortSegmentTimeout OBJECT-TYPE
SYNTAX INTEGER (3..30)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Time in seconds where segment fail timer expires, fail flag is set, and
expiry action is taken."
::= { extremeEapsSharedPortEntry 13 }
extremeEapsSharedPortCommonPathFailedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Shared port link fail timer expired, but our shared port link is up."
::= { extremeEapsSharedPortEntry 14 }
extremeEapsSharedPortCommonPathHealthInterval OBJECT-TYPE
SYNTAX INTEGER (1..10)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Interval at which health check PDUs are sent out shared port."
::= { extremeEapsSharedPortEntry 15 }
extremeEapsSharedPortCommonPathTimeout OBJECT-TYPE
SYNTAX INTEGER (3..30)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Time in seconds where shared link fail timer expires and fail flag is set"
::= { extremeEapsSharedPortEntry 16 }
extremeEapsSharedPortSegmentTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeEapsSharedPortSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table contains the EAPS shared port's segments
information"
::= { extremeEaps 6 }
extremeEapsSharedPortSegmentEntry OBJECT-TYPE
SYNTAX ExtremeEapsSharedPortSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An individual entry of this table describes the EAPS
shared port's segment information. It will describe the
EAPS domain, the segment's status, and other information
related to neighboring node's blocking status."
INDEX { extremeEapsSharedPortIfIndex,
extremeEapsSharedPortSegmentPort,
extremeEapsName
}
::= { extremeEapsSharedPortSegmentTable 1 }
ExtremeEapsSharedPortSegmentEntry ::= SEQUENCE {
extremeEapsSharedPortSegmentPort EapsRingPort,
extremeEapsSharedPortSegmentStatus EapsSharedPortSegmentStatus,
extremeEapsSharedPortSegmentFailedFlag TruthValue,
extremeEapsSharedPortSegmentVlanPortCount INTEGER,
extremeEapsSharedPortSegmentAdjId INTEGER,
extremeEapsSharedPortSegmentRBD INTEGER
}
extremeEapsSharedPortSegmentPort OBJECT-TYPE
SYNTAX EapsRingPort
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The segment port on a segment which is part of an EAPS
shared port."
::= { extremeEapsSharedPortSegmentEntry 1 }
extremeEapsSharedPortSegmentStatus OBJECT-TYPE
SYNTAX EapsSharedPortSegmentStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The status of a segment port which is part of an EAPS
shared port."
::= { extremeEapsSharedPortSegmentEntry 2 }
extremeEapsSharedPortSegmentFailedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The status of the failed flag on a segment port which is
part of an EAPS shared port.
This flag will be set to TRUE if the segment's fail timer
expiry action is set to sendAlert, and this timer expires"
::= { extremeEapsSharedPortSegmentEntry 3 }
extremeEapsSharedPortSegmentVlanPortCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The count of vlan ports being protected under this
segment's EAPS domain."
::= { extremeEapsSharedPortSegmentEntry 4 }
extremeEapsSharedPortSegmentAdjId OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The link Id of a neighboring node if the neighbor's
shared port instance was in blocking state."
::= { extremeEapsSharedPortSegmentEntry 5 }
extremeEapsSharedPortSegmentRBD OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Root Blocker Id as determined by the neighboring
node's shared port instance."
::= { extremeEapsSharedPortSegmentEntry 6 }
extremeEapsSharedPortVlanTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeEapsSharedPortVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table contains all VLANs protected by the EAPS
Shared Port instance."
::= { extremeEaps 7 }
extremeEapsSharedPortVlanEntry OBJECT-TYPE
SYNTAX ExtremeEapsSharedPortVlanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An individual entry of this table correlates a EAPS
Shared port instance with a VLAN protected by it."
INDEX { extremeEapsSharedPortIfIndex,
extremeEapsSharedPortVlanName
}
::= { extremeEapsSharedPortVlanTable 1 }
ExtremeEapsSharedPortVlanEntry ::= SEQUENCE {
extremeEapsSharedPortVlanName DisplayString,
extremeEapsSharedPortVlanPortCount INTEGER,
extremeEapsSharedPortVlanActiveOpenPort EapsRingPort
}
extremeEapsSharedPortVlanName OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The vlan being protected under this EAPS Shared port
instance"
::= { extremeEapsSharedPortVlanEntry 1 }
extremeEapsSharedPortVlanPortCount OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The count of vlan ports being protected under this
vlan"
::= { extremeEapsSharedPortVlanEntry 2 }
extremeEapsSharedPortVlanActiveOpenPort OBJECT-TYPE
SYNTAX EapsRingPort
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Segment port that is Active Open.
If there is no Active open port, then this value is 0."
::= { extremeEapsSharedPortVlanEntry 3 }
extremeEapsSharedPortVlanPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeEapsSharedPortVlanPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table contains the EAPS shared port's vlan-port's
information"
::= { extremeEaps 8 }
extremeEapsSharedPortVlanPortEntry OBJECT-TYPE
SYNTAX ExtremeEapsSharedPortVlanPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An individual entry of this table describes the EAPS
shared port's vlan port information. It will describe the
status of the vlan port under its protection."
INDEX { extremeEapsSharedPortIfIndex,
extremeEapsSharedPortVlanName,
extremeEapsSharedPortSegmentPort,
extremeEapsName
}
::= { extremeEapsSharedPortVlanPortTable 1 }
ExtremeEapsSharedPortVlanPortEntry ::= SEQUENCE {
extremeEapsSharedPortVlanPortStatus EapsSharedPortVlanPortStatus
}
extremeEapsSharedPortVlanPortStatus OBJECT-TYPE
SYNTAX EapsSharedPortVlanPortStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The status of a vlan port which is getting protected
by an EAPS shared port."
::= { extremeEapsSharedPortVlanPortEntry 1 }
END