mibs/extreme/EXTREME-QOS-MIB
-- ===============================================================================
--
-- Extreme QoS objects
--
EXTREME-QOS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY FROM SNMPv2-SMI
OBJECT-TYPE FROM SNMPv2-SMI
TruthValue FROM SNMPv2-TC
DisplayString FROM RFC1213-MIB
RowStatus FROM SNMPv2-TC
ifIndex FROM RFC1213-MIB
extremeVlanIfIndex FROM EXTREME-VLAN-MIB
extremeAgent FROM EXTREME-BASE-MIB;
extremeQos MODULE-IDENTITY
LAST-UPDATED "0007240000Z"
ORGANIZATION "Extreme Networks, Inc."
CONTACT-INFO "www.extremenetworks.com"
DESCRIPTION "Extreme Quality-of-Service objects"
::= { extremeAgent 3 }
extremeQosCommon OBJECT IDENTIFIER ::= { extremeQos 1 }
extremeUnitPaceMode OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(1),
normalEthernet(2),
lowLatency(3)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object specifies whether the device currently
recognises and gives priority treatment to the
forwarding of packets with the PACE(tm) bit set in
their MAC Source Address fields.
PACE(tm) mode applies to the whole unit only and
is only valid when device is in Ingress QoS mode
as specified by extremeQosMode ingress(1). This
object will report notApplicable(1) when in
egress(2) mode. Set operations with value
notApplicable(1) will be rejected."
::= { extremeQosCommon 1 }
--
-- Select QoS Mode
--
extremeQosMode OBJECT-TYPE
SYNTAX INTEGER { ingress(1), egress(2) }
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Indicates which QoS mode the device should
use. ingress(1) applies priority-based QoS based
on the incoming packet's destination IP or MAC
address, 802.1p priority, PACE(tm), Source Port or
VLAN. egress(2) applies priority- and bandwidth-based
QoS based on destination IP or MAC address or VLAN.
See ExtremeWare documentation for further information."
::= { extremeQosCommon 4 }
--
-- Reset all QoS settings to defaults
--
extremeQosUnconfigure OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"Setting this to true will reset all QoS settings
in the device to factory defaults. Reads from this
value return an undefined value."
::= { extremeQosCommon 5 }
--
-- QoS Profile table
--
extremeQosProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeQosProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists QoS profiles."
::= { extremeQosCommon 6 }
extremeQosProfileEntry OBJECT-TYPE
SYNTAX ExtremeQosProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An individual QoS profile Entry."
INDEX {extremeQosProfileIndex}
::= {extremeQosProfileTable 1}
ExtremeQosProfileEntry ::= SEQUENCE {
extremeQosProfileIndex INTEGER,
extremeQosProfileName DisplayString,
extremeQosProfileMinBw INTEGER,
extremeQosProfileMaxBw INTEGER,
extremeQosProfilePriority INTEGER,
extremeQosProfileRowStatus RowStatus
}
extremeQosProfileIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
qos table."
::= { extremeQosProfileEntry 1}
extremeQosProfileName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..127))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A unique qos profile name."
::= {extremeQosProfileEntry 2}
extremeQosProfileMinBw OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minumum percentage of bandwidth that this queue requires.
The Switch is required to provide the minumum amount of
bandwidth to the queue. The lowest possible value is 0%."
DEFVAL { 0 }
::= {extremeQosProfileEntry 3 }
extremeQosProfileMaxBw OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum percentage of bandwidth that this queue is
permitted to use.
If a non-default value is set for this object then it negates
any previously set value of extremeQosProfileMaxSustBwBps. In
In addition, a set operation that supplies non-default values
for both this object and for extremeQosProfileMaxSustBwBps
will be rejected by the agent. In other words, you may supply
either an absolute or a percent limit, not both."
DEFVAL { 100 }
::= {extremeQosProfileEntry 4 }
extremeQosProfilePriority OBJECT-TYPE
SYNTAX INTEGER {
low(1),
lowHi(2),
normal(3),
normalHi(4),
medium(5),
mediumHi(6),
high(7),
highHi(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The level of priority in which this queue will be
serviced by the Switch."
::= {extremeQosProfileEntry 5 }
extremeQosProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of the extremeQosProfile entry.
This object can be set to:
active(1)
createAndGo(4)
createAndWait(5)
destroy(6)
The following values may be read:
active(1)
notInService(2)
notReady(3).
Setting this object to createAndGo(4) causes the agent
to attempt to create and commit the row based on
the contents of the objects in the row. If all necessary
information is present in the row and the values are
acceptible to the agent, the agent will change the
status to active(1). If any of the necessary objects
are not available, the agent will reject the creation
request.
Setting this object to createAndWait(5) causes a row
in this table to be created. The agent sets the
status to notInService(2) if all of the information is
present in the row and the values are acceptable to the
agent; otherwise, the agent sets the status to notReady(3).
Setting this object to active(1) is only valid when
the current status is active(1) or notInService(2).
When the state of the row transitions is set to active(1),
the agent creates the corresponding row in the ifTable..
Setting this object to destroy(6) will remove the
corresponding QoS Profile Entry.
In order for a set of this object to destroy(6) to succeed,
all dependencies on this row must have been removed. These
will include any stacking dependencies in the ifStackTable
and any protocol specific tables dependencies."
::= { extremeQosProfileEntry 6 }
--
-- VLAN-based QoS Table
--
extremeQosByVlanMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeQosByVlanMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table to associate a Vlan with the QoS profile that the
Vlan is using. Every Vlan is assigned a Qos Profile and
hence there is an entry in this table corresponding to every
entry in the extremeVlanIfTable."
::= { extremeQosCommon 7 }
extremeQosByVlanMappingEntry OBJECT-TYPE
SYNTAX ExtremeQosByVlanMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The QoS associated with a particular Vlan."
INDEX {extremeVlanIfIndex}
::= {extremeQosByVlanMappingTable 1}
ExtremeQosByVlanMappingEntry ::= SEQUENCE {
extremeQosByVlanMappingQosProfileIndex INTEGER
}
extremeQosByVlanMappingQosProfileIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Value of extremeQosProfileIndex that uniquely
identifies a QoS Profile entry in extremeQosProfileTable.
This indicates the QoS to be given to traffic for this
Vlan in the absence of any other more specific
configuration information for this traffic."
::= { extremeQosByVlanMappingEntry 1 }
--
-- Per Port QOS Table
--
extremePerPortQosTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremePerPortQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Global Qos Profiles are defined in the
extremeQosProfileTable. This table contains a list
of ports for which the definition of certain global
Qos Profiles has been overridden. The new definition
of the Qos profile parameters is in this table."
::= { extremeQosCommon 8 }
extremePerPortQosEntry OBJECT-TYPE
SYNTAX ExtremePerPortQosEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An individual overridden QoS profile Entry."
INDEX {ifIndex, extremePerPortQosIndex}
::= {extremePerPortQosTable 1}
ExtremePerPortQosEntry ::= SEQUENCE {
extremePerPortQosIndex INTEGER,
extremePerPortQosMinBw INTEGER,
extremePerPortQosMaxBw INTEGER,
extremePerPortQosPriority INTEGER,
extremePerPortQosRowStatus RowStatus
}
extremePerPortQosIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this variable is the same as the value
of extremeQosProfileIndex of the Qos Profile which
is overridden (for the port specified by ifIndex) by
the definition in this table."
::= { extremePerPortQosEntry 1}
extremePerPortQosMinBw OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minumum percentage of bandwidth that this queue on the
specified port requires. The Switch is required to provide
the minumum amount of bandwidth to the queue. The lowest
possible value is 0%."
DEFVAL { 0 }
::= {extremePerPortQosEntry 2 }
extremePerPortQosMaxBw OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum percentage of bandwidth that this queue on the
specified port is permitted to use."
DEFVAL { 100 }
::= {extremePerPortQosEntry 3 }
extremePerPortQosPriority OBJECT-TYPE
SYNTAX INTEGER {
low(1),
lowHi(2),
normal(3),
normalHi(4),
medium(5),
mediumHi(6),
high(7),
highHi(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The level of priority in which this queue will be
serviced by the Switch."
::= {extremePerPortQosEntry 4 }
extremePerPortQosRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of the extremePerPortQos entry.
This object can be set to
active(1)
createAndGo(4)
The following value may be read:
active(1)
Note that a destroy(6) is not supported. A row will only be
deleted from this table when the Qos Profile indicated
in that row is changed globally."
::= { extremePerPortQosEntry 5 }
--
-- QoS Ingress Priority
--
extremeQosIngressPriorityTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeQosIngressPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists QoS ingress priority settings."
::= { extremeQosCommon 9 }
extremeQosIngressPriorityEntry OBJECT-TYPE
SYNTAX ExtremeQosIngressPriorityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An individual QoS ingress priority Entry."
INDEX {extremeQosIngressPriorityIndex}
::= {extremeQosIngressPriorityTable 1}
ExtremeQosIngressPriorityEntry ::= SEQUENCE {
extremeQosIngressPriorityIndex INTEGER,
extremeQosIngressPriorityName DisplayString,
extremeQosIngressPriorityValue INTEGER
}
extremeQosIngressPriorityIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
qos ingress priority table."
::= { extremeQosIngressPriorityEntry 1}
extremeQosIngressPriorityName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..15))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A qos ingress priority name."
::= {extremeQosIngressPriorityEntry 2}
extremeQosIngressPriorityValue OBJECT-TYPE
SYNTAX INTEGER (0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ingress Qos priority value."
::= { extremeQosIngressPriorityEntry 3}
--
-- IQoS Profile table
--
extremeIQosProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeIQosProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists ingress QoS profiles."
::= { extremeQosCommon 10 }
extremeIQosProfileEntry OBJECT-TYPE
SYNTAX ExtremeIQosProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An individual ingress QoS profile Entry."
INDEX {ifIndex ,
extremeIQosProfileIndex}
::= {extremeIQosProfileTable 1}
ExtremeIQosProfileEntry ::= SEQUENCE {
extremeIQosProfileIndex INTEGER,
extremeIQosProfileName DisplayString,
extremeIQosProfileMinBwType INTEGER,
extremeIQosProfileMinBw INTEGER,
extremeIQosProfileMaxBwType INTEGER,
extremeIQosProfileMaxBw INTEGER,
extremeIQosProfileRED INTEGER,
extremeIQosProfileMaxBuf INTEGER
}
extremeIQosProfileIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An index that uniquely identifies an entry in the
ingress Qos table."
::= { extremeIQosProfileEntry 1}
extremeIQosProfileName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..127))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A unique ingress Qos profile name."
::= {extremeIQosProfileEntry 2}
extremeIQosProfileMinBwType OBJECT-TYPE
SYNTAX INTEGER {
percentage(1),
kbps(2),
mbps(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the current minimum bandwith setting. A value
of 1 signifies that the minimum bandwith value is a percentage
of the configurable port bandwidth. A value of 2 or 3 signifies
a guaranteed minimum available bandwidth in Kbps or Mbps
respectively."
::= {extremeIQosProfileEntry 3 }
extremeIQosProfileMinBw OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The guaranteed minimum bandwidth for this queue, expressed as either
a percentage or a specific bandwidth value, as specified by the value
of extremeIQosProfileMinBwType."
DEFVAL { 0 }
::= {extremeIQosProfileEntry 4 }
extremeIQosProfileMaxBwType OBJECT-TYPE
SYNTAX INTEGER {
percentage(1),
kbps(2),
mbps(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the current maximum bandwith setting. A value
of 1 signifies that the maximum bandwith value is a percentage
of the configurable port bandwidth. A value of 2 or 3 signifies
a maximum allowed bandwidth in Kbps or Mbps respectively."
::= {extremeIQosProfileEntry 5 }
extremeIQosProfileMaxBw OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum allowed input bandwidth for this queue, expressed as
either a percentage or a specific bandwidth value, as specified by
the value of extremeIQosProfileMaxBwType."
DEFVAL { 0 }
::= {extremeIQosProfileEntry 6 }
extremeIQosProfileRED OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Random Early Drop threshold. When the input queue fill
ratio exceeds this percentage, frames start to drop randomly
with a linear increasing drop probability as the queue fill
count approaches the max queue size. A value of 100 indicates
that this feature is currently disabled."
::= {extremeIQosProfileEntry 7 }
extremeIQosProfileMaxBuf OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The percentage of the total ingress queue size to use. Lower values
can be used to reduce the max latency through this queue, but with
potentially greater loss with bursty traffic."
::= { extremeIQosProfileEntry 8 }
--
-- VLAN-based Ingress QoS Table
--
extremeIQosByVlanMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF ExtremeIQosByVlanMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table to associate a Vlan with the ingress QoS profile
that the Vlan is using. Every Vlan is assigned a Qos Profile
and hence there is an entry in this table corresponding to
every entry in the extremeVlanIfTable."
::= { extremeQosCommon 11 }
extremeIQosByVlanMappingEntry OBJECT-TYPE
SYNTAX ExtremeIQosByVlanMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ingress QoS associated with a particular Vlan."
INDEX {extremeVlanIfIndex}
::= {extremeIQosByVlanMappingTable 1}
ExtremeIQosByVlanMappingEntry ::= SEQUENCE {
extremeIQosByVlanMappingIQosProfileIndex INTEGER
}
extremeIQosByVlanMappingIQosProfileIndex OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Value of extremeIQosProfileIndex that uniquely
identifies an ingress QoS Profile entry in extremeIQosProfileTable.
This indicates the QoS to be given to traffic for this
Vlan in the absence of any other more specific
configuration information for this traffic."
::= { extremeIQosByVlanMappingEntry 1 }
END