mibs/fs/FS-FIBER-MIB
-- *****************************************************************
-- FS-FIBER-MIB.mib: FS FIBER MIB file
--
-- January 2012
--
-- Copyright (c) 2012 by FS.COM Inc
-- All rights reserved.
--
-- *****************************************************************
--
FS-FIBER-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Gauge32
FROM SNMPv2-SMI
TruthValue,
DisplayString
FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF
IfIndex
FROM FS-TC
fsMgmt
FROM FS-SMI
ifIndex,
ifDescr
FROM IF-MIB;
fsFiberMIB MODULE-IDENTITY
LAST-UPDATED "201111280000Z"
ORGANIZATION "FS.COM Inc"
CONTACT-INFO
"
Tel: 400-865-2852
E-mail: https://www.fs.com/live_chat_service_mail.html"
DESCRIPTION
"This module defines fs fiber module information mibs."
REVISION "201111280000Z"
DESCRIPTION
"Initial version of this MIB module."
::= { fsMgmt 105}
fsFiberMIBObjects OBJECT IDENTIFIER ::= { fsFiberMIB 1 }
-- ---------------------------------------------------------- --
-- A table for getting Fiber port information.
-- ---------------------------------------------------------- --
fsFiberTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSFiberEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table for getting Fiber Module information"
::= { fsFiberMIBObjects 1 }
fsFiberEntry OBJECT-TYPE
SYNTAX FSFiberEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of a Fiber Module information."
INDEX { fsFiberPortIndex }
::= { fsFiberTable 1 }
FSFiberEntry ::=
SEQUENCE {
fsFiberPortIndex IfIndex,
fsFiberPortDescr DisplayString,
fsFiberTransceiverType INTEGER,
fsFiberConnectorType INTEGER,
fsFiberWavelength INTEGER,
fsFiberTransferDistanceSMF INTEGER,
fsFiberTransferDistance62point5umOM1 INTEGER,
fsFiberTransferDistance62point5um INTEGER,
fsFiberTransferDistance50umOM2 INTEGER,
fsFiberTransferDistance50um INTEGER,
fsFiberTransferDistance50umOM3 INTEGER,
fsFiberTransferDistanceEBW50um INTEGER,
fsFiberTransferDistanceCopper INTEGER,
fsFiberTransferDistanceCableAssembly INTEGER,
fsFiberDDMSupportStatus TruthValue,
fsFiberSerialNumber DisplayString,
fsFiberTemp INTEGER,
fsFiberTempStatus INTEGER,
fsFiberVoltage INTEGER,
fsFiberVoltageStatus INTEGER,
fsFiberBias INTEGER,
fsFiberBiasStatus INTEGER,
fsFiberChannel1Bias INTEGER,
fsFiberChannel1BiasStatus INTEGER,
fsFiberChannel2Bias INTEGER,
fsFiberChannel2BiasStatus INTEGER,
fsFiberChannel3Bias INTEGER,
fsFiberChannel3BiasStatus INTEGER,
fsFiberChannel4Bias INTEGER,
fsFiberChannel4BiasStatus INTEGER,
fsFiberRXpowerIntegerpart INTEGER,
fsFiberRXpowerDecimalpart INTEGER,
fsFiberRXpowertype INTEGER,
fsFiberRXpowerStatus INTEGER,
fsFiberChannel1RXpowerIntegerpart INTEGER,
fsFiberChannel1RXpowerDecimalpart INTEGER,
fsFiberChannel1RXpowertype INTEGER,
fsFiberChannel1RXpowerStatus INTEGER,
fsFiberChannel2RXpowerIntegerpart INTEGER,
fsFiberChannel2RXpowerDecimalpart INTEGER,
fsFiberChannel2RXpowertype INTEGER,
fsFiberChannel2RXpowerStatus INTEGER,
fsFiberChannel3RXpowerIntegerpart INTEGER,
fsFiberChannel3RXpowerDecimalpart INTEGER,
fsFiberChannel3RXpowertype INTEGER,
fsFiberChannel3RXpowerStatus INTEGER,
fsFiberChannel4RXpowerIntegerpart INTEGER,
fsFiberChannel4RXpowerDecimalpart INTEGER,
fsFiberChannel4RXpowertype INTEGER,
fsFiberChannel4RXpowerStatus INTEGER,
fsFiberTXpowerIntegerpart INTEGER,
fsFiberTXpowerDecimalpart INTEGER,
fsFiberTXpowerStatus INTEGER,
fsFiberChannel1TXpowerIntegerpart INTEGER,
fsFiberChannel1TXpowerDecimalpart INTEGER,
fsFiberChannel1TXpowerStatus INTEGER,
fsFiberChannel2TXpowerIntegerpart INTEGER,
fsFiberChannel2TXpowerDecimalpart INTEGER,
fsFiberChannel2TXpowerStatus INTEGER,
fsFiberChannel3TXpowerIntegerpart INTEGER,
fsFiberChannel3TXpowerDecimalpart INTEGER,
fsFiberChannel3TXpowerStatus INTEGER,
fsFiberChannel4TXpowerIntegerpart INTEGER,
fsFiberChannel4TXpowerDecimalpart INTEGER,
fsFiberChannel4TXpowerStatus INTEGER,
fsFiberRXpowerSign INTEGER,
fsFiberChannel1RXpowerSign INTEGER,
fsFiberChannel2RXpowerSign INTEGER,
fsFiberChannel3RXpowerSign INTEGER,
fsFiberChannel4RXpowerSign INTEGER,
fsFiberTXpowerSign INTEGER,
fsFiberChannel1TXpowerSign INTEGER,
fsFiberChannel2TXpowerSign INTEGER,
fsFiberChannel3TXpowerSign INTEGER,
fsFiberChannel4TXpowerSign INTEGER,
fsFiberRXpower INTEGER,
fsFiberChannel1RXpower INTEGER,
fsFiberChannel2RXpower INTEGER,
fsFiberChannel3RXpower INTEGER,
fsFiberChannel4RXpower INTEGER,
fsFiberTXpower INTEGER,
fsFiberChannel1TXpower INTEGER,
fsFiberChannel2TXpower INTEGER,
fsFiberChannel3TXpower INTEGER,
fsFiberChannel4TXpower INTEGER,
fsFiberWavelengthExact DisplayString,
fsFiberTransferDistance50umOM4 INTEGER,
fsFiberTransferDistanceSMFExt INTEGER,
fsFiberBandWidth INTEGER,
fsFiberFormFactor INTEGER,
fsFiberRXpowerLowWarnThreshold INTEGER,
fsFiberRXpowerHighWarnThreshold INTEGER,
fsFiberRXpowerLowAlarmThreshold INTEGER,
fsFiberRXpowerHighAlarmThreshold INTEGER,
fsFiberTXpowerLowWarnThreshold INTEGER,
fsFiberTXpowerHighWarnThreshold INTEGER,
fsFiberTXpowerLowAlarmThreshold INTEGER,
fsFiberTXpowerHighAlarmThreshold INTEGER,
fsFiberChannel5Bias INTEGER,
fsFiberChannel5BiasStatus INTEGER,
fsFiberChannel6Bias INTEGER,
fsFiberChannel6BiasStatus INTEGER,
fsFiberChannel7Bias INTEGER,
fsFiberChannel7BiasStatus INTEGER,
fsFiberChannel8Bias INTEGER,
fsFiberChannel8BiasStatus INTEGER,
fsFiberChannel5RXpowerIntegerpart INTEGER,
fsFiberChannel5RXpowerDecimalpart INTEGER,
fsFiberChannel5RXpowertype INTEGER,
fsFiberChannel5RXpowerStatus INTEGER,
fsFiberChannel6RXpowerIntegerpart INTEGER,
fsFiberChannel6RXpowerDecimalpart INTEGER,
fsFiberChannel6RXpowertype INTEGER,
fsFiberChannel6RXpowerStatus INTEGER,
fsFiberChannel7RXpowerIntegerpart INTEGER,
fsFiberChannel7RXpowerDecimalpart INTEGER,
fsFiberChannel7RXpowertype INTEGER,
fsFiberChannel7RXpowerStatus INTEGER,
fsFiberChannel8RXpowerIntegerpart INTEGER,
fsFiberChannel8RXpowerDecimalpart INTEGER,
fsFiberChannel8RXpowertype INTEGER,
fsFiberChannel8RXpowerStatus INTEGER,
fsFiberChannel5TXpowerIntegerpart INTEGER,
fsFiberChannel5TXpowerDecimalpart INTEGER,
fsFiberChannel5TXpowerStatus INTEGER,
fsFiberChannel6TXpowerIntegerpart INTEGER,
fsFiberChannel6TXpowerDecimalpart INTEGER,
fsFiberChannel6TXpowerStatus INTEGER,
fsFiberChannel7TXpowerIntegerpart INTEGER,
fsFiberChannel7TXpowerDecimalpart INTEGER,
fsFiberChannel7TXpowerStatus INTEGER,
fsFiberChannel8TXpowerIntegerpart INTEGER,
fsFiberChannel8TXpowerDecimalpart INTEGER,
fsFiberChannel8TXpowerStatus INTEGER,
fsFiberChannel5RXpowerSign INTEGER,
fsFiberChannel6RXpowerSign INTEGER,
fsFiberChannel7RXpowerSign INTEGER,
fsFiberChannel8RXpowerSign INTEGER,
fsFiberChannel5TXpowerSign INTEGER,
fsFiberChannel6TXpowerSign INTEGER,
fsFiberChannel7TXpowerSign INTEGER,
fsFiberChannel8TXpowerSign INTEGER,
fsFiberChannel5RXpower INTEGER,
fsFiberChannel6RXpower INTEGER,
fsFiberChannel7RXpower INTEGER,
fsFiberChannel8RXpower INTEGER,
fsFiberChannel5TXpower INTEGER,
fsFiberChannel6TXpower INTEGER,
fsFiberChannel7TXpower INTEGER,
fsFiberChannel8TXpower INTEGER,
fsFiberTransferDistance50umOM5 INTEGER,
fsFiberMode INTEGER,
fsFiberTempLowWarnThreshold INTEGER,
fsFiberTempHighWarnThreshold INTEGER,
fsFiberTempLowAlarmThreshold INTEGER,
fsFiberTempHighAlarmThreshold INTEGER,
fsFiberVoltageLowWarnThreshold INTEGER,
fsFiberVoltageHighWarnThreshold INTEGER,
fsFiberVoltageLowAlarmThreshold INTEGER,
fsFiberVoltageHighAlarmThreshold INTEGER,
fsFiberBiasLowWarnThreshold INTEGER,
fsFiberBiasHighWarnThreshold INTEGER,
fsFiberBiasLowAlarmThreshold INTEGER,
fsFiberBiasHighAlarmThreshold INTEGER
}
fsFiberPortIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Port index of the port."
::= { fsFiberEntry 1 }
fsFiberPortDescr OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Discription of the port."
::= { fsFiberEntry 2 }
fsFiberTransceiverType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
fiber100BASEGTSFP(2),
fiber100BASESXSFP(3),
fiber100BASELXSFP(4),
fiber100BASELHSFP(5),
fiber100BASEZXSFP(6),
fiber100CopperSFP(7),
fiber1000BASEGTSFP(8),
fiber1000BASESXSFP(9),
fiber1000BASELXSFP(10),
fiber1000BASELHSFP(11),
fiber1000BASEZXSFP(12),
fiber1000CopperSFP(13),
fiber10GCopperSFPPlus(14),
fiber10GBASESRSFPPlus(15),
fiber10GBASELRSFPPlus(16),
fiber10GBASEERSFPPlus(17),
fiber10GBASEZRSFPPlus(18),
fiber10GCopperXFP(19),
fiber10GBASESRXFP(20),
fiber10GBASELRXFP(21),
fiber10GBASEERXFP(22),
fiber10GBASEZRXFP(23),
fiber40GActiveCableQSFPPlus(24),
fiber40GLR4QSFPPlus(25),
fiber40GCopperQSFPPlus(26),
fiber40GSR4QSFPPlus(27),
fiber2500CopperSFP(28),
fiberFC16G(29),
fiberFC8G(30),
fiberFC4G(31),
fiberFC2G(32),
fiber10GActiveCableSFPPlus(33),
fiber40GER4QSFPPlus(34),
fiber40GZR4QSFPPlus(35),
fiber100GCABLEQSFP28(36),
fiber100GLR4QSFP28(37),
fiber100GSR4QSFP28(38),
fiber100GER4QSFP28(39),
fiber100GZR4QSFP28(40),
fiber100GCR4QSFP28(41),
fiber100GPSM4QSFP28(42),
fiber25GSRSFP28 (43),
fiber25GLRSFP28 (44),
fiber25GERSFP28 (45),
fiber25GZRSFP28 (46),
fiber25GCOPPERSFP28 (47),
fiber25GACTIVECABLESFP28 (48),
fiber100GiLR4QSFP28(49),
fiber10GBASELRMSFPPlus(50),
fiber40GLSR4QSFPPlus(51),
fiber40GSWDM4QSFPPlus(52),
fiber40GiLR4QSFPPlus(53),
fiber40GPSM4QSFPPlus(54),
fiber40GSR4BiDiQSFPPlus(55),
fiber100GSWDM4QSFP28(56),
fiber100GPAM4BiDiQSFP28(57),
fiber100GER4LiteQSFP28(58),
fiber100G4WDM40QSFP28(59),
fiber100GDWDM2QSFP28(60),
fiber40GZRQSFPPlus(61),
fiber100GZRQSFP28(62),
fiber100GCWDM4QSFP28(63),
fiber10GPASSIVECOPPERSFPPlus(64),
fiber10GACTIVECOPPERSFPPlus(65),
fiber10GLOOPBACKSFPPlus(66),
fiber40GPASSIVECOPPERQSFPPlus(67),
fiber40GACTIVECOPPERQSFPPlus(68),
fiber40GLOOPBACKQSFPPlus(69),
fiber100GPASSIVECOPPERQSFP28(70),
fiber100GACTIVECOPPERQSFP28(71),
fiber100GLOOPBACKQSFP28(72),
fiber25GPASSIVECOPPERSFP28(73),
fiber25GACTIVECOPPERSFP28(74),
fiber25GLOOPBACKSFP28(75),
fiber200GSR4QSFP56(76),
fiber200GFR4QSFP56(77),
fiber200GPASSIVECOPPERQSFP56(78),
fiber200GACTIVECOPPERQSFP56(79),
fiber400GSR8QSFPDD(80),
fiber400GDR4QSFPDD(81),
fiber400GFR4QSFPDD(82),
fiber400GPASSIVECOPPERQSFPDD(83),
fiber400GACTIVECABLEQSFPDD(84),
fiber400GLR8QSFPDD(85),
fiber200GLOOPBACKQSFP56(86),
fiber400GACTIVECOPPERQSFPDD(87),
fiber400GLOOPBACKQSFPDD(88),
fiber100GPASSIVECOPPERDSFP(89),
fiber100GACTIVECOPPERDSFP(90),
fiber100GACTIVECABLEDSFP(91),
fiber100GLOOPBACKDSFP(92),
fiber100GDR1QSFP28(93),
fiber100GFR1QSFP28(94),
fiber400GZRQSFPDD(95),
fiber2500BASESXSFP(96),
fiber2500BASELXSFP(97),
fiber200GACTIVECABLEQSFP56(98),
fiber40GLX4QSFPPlus(99),
fiber10GBASELR8SFX(100),
fiber1000BASELX8SFG(101),
fiber10GCOPPER8SFX(102),
fiber10GBASETXFP(103),
fiber400GZRPlusQSFPDD(104),
fiber400GLR4QSFPDD(105)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Transceiver type of the Fiber module insered into the port."
::= { fsFiberEntry 3 }
fsFiberConnectorType OBJECT-TYPE
SYNTAX INTEGER {
meaningless(0),
unknownorunspecified(1),
vendorspecific(2),
sc(3),
fiberChannelStyle1CopperConnector(4),
fiberChannelStyle2CopperConnector(5),
bncortnc(6),
fiberChannelCoaxialHeaders(7),
fiberJack(8),
lc(9),
mtrj(10),
mu(11),
sg(12),
opticalPigtail(13),
hssdcII(14),
copperPigtail(15),
mpo(16),
rj45(17),
noSeparableConnector(18),
mxc(19)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Connector type of the Fiber module insered into the port.
If the transceiver type of Fiber module is unknown(1), then this
object contains a zero value."
::= { fsFiberEntry 4 }
fsFiberWavelength OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of wavelength of the Fiber module insered into the port.
If the transceiver type of Fiber module is either fiber100CopperSFP(7)
or fiber1000CopperSFP(13) (or fiber10GCopperSFPPlus(14),
or fiber10GCopperXFP(19), or fiber40GCopperQSFPPlus(26), or fiber2500CopperSFP(28), or unknown(1)), then this
object contains a zero value."
::= { fsFiberEntry 5 }
fsFiberTransferDistanceSMF OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using single mode fiber for. The value is in units of kilometers.
A value of zero means that the transceiver does not support single mode fiber."
::= { fsFiberEntry 6 }
fsFiberTransferDistance62point5umOM1 OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using 62.5 micron multimode (200 MHz*Km at 850 nm, 500 MHz*Km
at 1310 nm) fiber. The value is in units of meters.
A value of zero means that the transceiver does not
support 62.5 micron multimode fiber or the Fiber module type
is neither SFP/SFP+ nor QSFP+."
::= { fsFiberEntry 7 }
fsFiberTransferDistance62point5um OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using 62.5 micron core multimode (200 MHz*Km at 850 nm, 500 MHz*Km
at 1310 nm) fiber. The value is in units of meters.
A value of zero means that the transceiver does not
support 62.5 micron multimode fiber or the Fiber module type is not XFP."
::= { fsFiberEntry 8 }
fsFiberTransferDistance50umOM2 OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using 50 micron multimode (500 MHz*Km at 850 nm for SFP module
or at 850 nm and 1310 nm for QSFP+ module) fiber. The value is in units of meters.
A value of zero means that the transceiver does not
support 50 micron multimode fiber or the Fiber module type
is neither SFP/SFP+ nor QSFP+."
::= { fsFiberEntry 9 }
fsFiberTransferDistance50um OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using 50 micron core multimode (500 MHz*Km at 850 nm and 1310 nm) fiber.
The value is in units of meters.
A value of zero means that the transceiver does not
support 50 micron core multimode fiber or the Fiber module type
is not XFP."
::= { fsFiberEntry 10 }
fsFiberTransferDistance50umOM3 OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using 50 micron multimode OM3(2000 MHz*Km) fiber.
The value is in units of meters.
A value of zero means that the transceiver does not
support 50 micron multimode fiber or the Fiber module type
is neither SFP/SFP+ nor QSFP+."
::= { fsFiberEntry 11 }
fsFiberTransferDistanceEBW50um OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using 2000 MHz*Km (850nm) extended bandwidth 50
micron core multimode fiber. The value is in units of meters.
A value of zero means that the transceiver does not support
extended bandwidth 50 micron multimode fiber or the Fiber module type is not XFP."
::= { fsFiberEntry 12 }
fsFiberTransferDistanceCopper OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using copper cables. The value is in units of meters.
A value of zero means that the transceiver does not support copper cables
or the Fiber module type is neither SFP/SFP+ nor XFP."
::= { fsFiberEntry 13 }
fsFiberTransferDistanceCableAssembly OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length of the Cable assembly passive.
The value is in units of meters.
A value of zero means that the transceiver is not a cable assemblyor
or the Fiber module type is not QSFP+."
::= { fsFiberEntry 14 }
fsFiberDDMSupportStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates that whether the Digital Diagnostic Monitors is implemeted."
::= { fsFiberEntry 15 }
fsFiberSerialNumber OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The serial number of the Fiber module insered into the port."
::= { fsFiberEntry 16 }
fsFiberTemp OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The temperature of the Fiber module insered into the port.
The value is in units of degrees Celsius.
If the fsFiberDDMSupportStatus is false, the temperature value is 0."
::= { fsFiberEntry 17 }
fsFiberTempStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the temperature of the Fiber module is in
the normal level. The status warning(3) indicates that the temperature of
the Fiber module exceeds high warning level or is below low warning level.
The status alarm(4) indicates that the temperature of
the Fiber module exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP(or not QSFP+), the status is unknown(1)."
::= { fsFiberEntry 18 }
fsFiberVoltage OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The voltage of the Fiber module insered into the port.
The value is in units of mVolts.
If the fsFiberDDMSupportStatus is false, the voltage value is 0."
::= { fsFiberEntry 19 }
fsFiberVoltageStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the voltage of the Fiber module is in
the normal level. The status warning(3) indicates that the voltage of
the Fiber module exceeds high warning level or is below low warning level.
The status alarm(4) indicates that the voltage of
the Fiber module exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP(or not QSFP+), the status is unknown(1)."
::= { fsFiberEntry 20 }
fsFiberBias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias of the Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP, the bias value is 0."
::= { fsFiberEntry 21 }
fsFiberBiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias of the Fiber module is in
the normal level. The status warning(3) indicates that the bias of
the Fiber module exceeds high warning level or is below low warning level.
The status alarm(4) indicates that the bias of
the Fiber module exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP, the status is unknown(1)."
::= { fsFiberEntry 22 }
fsFiberChannel1Bias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias in Channel 1 of the QSFP+ Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the bias value in Channel 1 is 0."
::= { fsFiberEntry 23 }
fsFiberChannel1BiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias in the Channel 1 of QSFP+ is in
the normal level. The status warning(3) indicates
that the bias in the Channel 1 exceeds high warning level or is
below low warning level. The status alarm(4) indicates that the bias in
the Channel 1 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 24 }
fsFiberChannel2Bias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias in Channel 2 of the QSFP+ Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the bias value in Channel 2 is 0."
::= { fsFiberEntry 25 }
fsFiberChannel2BiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias in the Channel 2 of QSFP+ is in
the normal level. The status warning(3) indicates
that the bias in the Channel 2 exceeds high warning level or is
below low warning level. The status alarm(4) indicates that the bias in
the Channel 2 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 26 }
fsFiberChannel3Bias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias in Channel 3 of the QSFP+ Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the bias value in Channel 3 is 0."
::= { fsFiberEntry 27 }
fsFiberChannel3BiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias in the Channel 3 of QSFP+ is in
the normal level. The status warning(3) indicates
that the bias in the Channel 3 exceeds high warning level or is
below low warning level. The status alarm(4) indicates that the bias in
the Channel 3 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 28 }
fsFiberChannel4Bias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias in Channel 4 of the QSFP+ Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the bias value in Channel 4 is 0."
::= { fsFiberEntry 29 }
fsFiberChannel4BiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias in the Channel 4 of QSFP+ is in
the normal level. The status warning(3) indicates
that the bias in the Channel 4 exceeds high warning level or is
below low warning level. The status alarm(4) indicates that the bias in
the Channel 4 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 30 }
fsFiberRXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power of the Fiber module insered into the port.
The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP, the integer part of Rx power value
is -100(means that the value is invalid)."
::= { fsFiberEntry 31 }
fsFiberRXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power of the Fiber module insered into the port.
The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP, the decimal part of Rx power value
is -100(means that the value is invalid)."
::= { fsFiberEntry 32 }
fsFiberRXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3).
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP (or not QSFP+), the value is unknown(1)."
::= { fsFiberEntry 33 }
fsFiberRXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power of the Fiber module is in
the normal level. The status warning(3) indicates that the Rx power of
the Fiber module exceeds high warning level or is below low warning level.
The status alarm(4) indicates that the Rx power of
the Fiber module exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP, the status is unknown(1)."
::= { fsFiberEntry 34 }
fsFiberChannel1RXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power in Channel 1 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the integer part of Rx power value in Channel 1
is -100(means the value is invalid)."
::= { fsFiberEntry 35 }
fsFiberChannel1RXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power in Channel 1 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the decimal part of Rx power value in Channel 1
is -100(means the value is invalid)."
::= { fsFiberEntry 36 }
fsFiberChannel1RXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3) in Channel 1 of QSFP+.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the value is unknown(1)."
::= { fsFiberEntry 37 }
fsFiberChannel1RXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power in the Channel 1 of QSFP+ is in
the normal level. The status warning(3) indicates that
the Rx power in the Channel 1 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Rx power in the
Channel 1 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 38 }
fsFiberChannel2RXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power in Channel 1 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the integer part of Rx power value in Channel 1
is -100(means the value is invalid)."
::= { fsFiberEntry 39 }
fsFiberChannel2RXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power in Channel 1 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the decimal part of Rx power value in Channel 2
is -100(means the value is invalid)."
::= { fsFiberEntry 40 }
fsFiberChannel2RXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3) in Channel 2 of QSFP+.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the value is unknown(1)."
::= { fsFiberEntry 41 }
fsFiberChannel2RXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power in the Channel 2 of QSFP+ is in
the normal level. The status warning(3) indicates that
the Rx power in the Channel 2 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Rx power in the
Channel 2 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 42 }
fsFiberChannel3RXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power in Channel 3 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the integer part of Rx power value in Channel 3
is -100(means the value is invalid)."
::= { fsFiberEntry 43 }
fsFiberChannel3RXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power in Channel 3 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the decimal part of Rx power value in Channel 3
is -100(means the value is invalid)."
::= { fsFiberEntry 44 }
fsFiberChannel3RXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3) in Channel 3 of QSFP+.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the value is unknown(1)."
::= { fsFiberEntry 45 }
fsFiberChannel3RXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power in the Channel 3 of QSFP+ is in
the normal level. The status warning(3) indicates that
the Rx power in the Channel 3 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Rx power in the
Channel 3 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 46 }
fsFiberChannel4RXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power in Channel 4 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the integer part of Rx power value in Channel 4
is -100(means the value is invalid)."
::= { fsFiberEntry 47 }
fsFiberChannel4RXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power in Channel 4 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the decimal part of Rx power value in Channel 4
is -100(means the value is invalid)."
::= { fsFiberEntry 48 }
fsFiberChannel4RXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3) in Channel 4 of QSFP+.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the value is unknown(1)."
::= { fsFiberEntry 49 }
fsFiberChannel4RXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power in the Channel 4 of QSFP+ is in
the normal level. The status warning(3) indicates that
the Rx power in the Channel 4 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Rx power in the
Channel 4 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 50 }
fsFiberTXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power of the Fiber module insered into the port.
The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP, the integer part of Tx power value
is -100(means that the value is invalid)."
::= { fsFiberEntry 51 }
fsFiberTXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power of the Fiber module insered into the port.
The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP, the decimal part of Tx power value
is -100(means that the value is invalid)."
::= { fsFiberEntry 52 }
fsFiberTXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power of the Fiber module is in
the normal level. The status warning(3) indicates that the Tx power of
the Fiber module exceeds high warning level or is below low warning level.
The status alarm(4) indicates that the Tx power of
the Fiber module exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
neither SFP/SFP+ nor XFP, the status is unknown(1)."
::= { fsFiberEntry 53 }
fsFiberChannel1TXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power in Channel 1 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the integer part of Tx power value in Channel 1
is -100(means the value is invalid)."
::= { fsFiberEntry 54 }
fsFiberChannel1TXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power in Channel 1 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the decimal part of Tx power value in Channel 1
is -100(means the value is invalid)."
::= { fsFiberEntry 55 }
fsFiberChannel1TXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power in the Channel 1 of QSFP+ is in
the normal level. The status warning(3) indicates that
the Tx power in the Channel 1 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Tx power in the
Channel 1 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 56 }
fsFiberChannel2TXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power in Channel 1 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the integer part of Tx power value in Channel 1
is -100(means the value is invalid)."
::= { fsFiberEntry 57 }
fsFiberChannel2TXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power in Channel 1 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the decimal part of Tx power value in Channel 2
is -100(means the value is invalid)."
::= { fsFiberEntry 58 }
fsFiberChannel2TXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power in the Channel 2 of QSFP+ is in
the normal level. The status warning(3) indicates that
the Tx power in the Channel 2 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Tx power in the
Channel 2 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 59 }
fsFiberChannel3TXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power in Channel 3 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the integer part of Tx power value in Channel 3
is -100(means the value is invalid)."
::= { fsFiberEntry 60 }
fsFiberChannel3TXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power in Channel 3 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the decimal part of Tx power value in Channel 3
is -100(means the value is invalid)."
::= { fsFiberEntry 61 }
fsFiberChannel3TXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power in the Channel 3 of QSFP+ is in
the normal level. The status warning(3) indicates that
the Tx power in the Channel 3 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Tx power in the
Channel 3 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 62 }
fsFiberChannel4TXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power in Channel 4 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the integer part of Tx power value in Channel 4
is -100(means the value is invalid)."
::= { fsFiberEntry 63 }
fsFiberChannel4TXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power in Channel 4 of the QSFP+
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the decimal part of Tx power value in Channel 4
is -100(means the value is invalid)."
::= { fsFiberEntry 64 }
fsFiberChannel4TXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power in the Channel 4 of QSFP+ is in
the normal level. The status warning(3) indicates that
the Tx power in the Channel 4 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Tx power in the
Channel 4 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP+, the status is unknown(1)."
::= { fsFiberEntry 65 }
fsFiberRXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 66 }
fsFiberChannel1RXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 67 }
fsFiberChannel2RXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 68 }
fsFiberChannel3RXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 69 }
fsFiberChannel4RXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 70 }
fsFiberTXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 71 }
fsFiberChannel1TXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 72 }
fsFiberChannel2TXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 73 }
fsFiberChannel3TXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 74 }
fsFiberChannel4TXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 75 }
fsFiberRXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 76 }
fsFiberChannel1RXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power in Channel 1 of the QSFP+ Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 77 }
fsFiberChannel2RXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power in Channel 2 of the QSFP+ Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 78 }
fsFiberChannel3RXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power in Channel 3 of the QSFP+ Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 79 }
fsFiberChannel4RXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power in Channel 4 of the QSFP+ Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 80 }
fsFiberTXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 81 }
fsFiberChannel1TXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power in Channel 1 of the QSFP+ Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 82 }
fsFiberChannel2TXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power in Channel 2 of the QSFP+ Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 83 }
fsFiberChannel3TXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power in Channel 3 of the QSFP+ Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 84 }
fsFiberChannel4TXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power in Channel 4 of the QSFP+ Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 85 }
fsFiberWavelengthExact OBJECT-TYPE
SYNTAX DisplayString (SIZE(1..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of wavelength of the Fiber module insered into the port.
If the transceiver type of Fiber module is either fiber100CopperSFP(7)
or fiber1000CopperSFP(13) (or fiber10GCopperSFPPlus(14),
or fiber10GCopperXFP(19), or fiber40GCopperQSFPPlus(26), or fiber2500CopperSFP(28), or unknown(1)), then this
object contains a NA value."
::= { fsFiberEntry 86 }
fsFiberTransferDistance50umOM4 OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using 50 micron multimode OM4(4700 MHz*Km) fiber.
The value is in units of meters.
A value of zero means that the transceiver does not
support 50 micron multimode fiber or the Fiber module type
is neither SFP/SFP+ nor QSFP+."
::= { fsFiberEntry 87 }
fsFiberTransferDistanceSMFExt OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using single mode fiber for. The value is in units of meters.
A value of zero means that the transceiver does not support single mode fiber."
::= { fsFiberEntry 88 }
fsFiberBandWidth OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer maximum available bandwidth of the Fiber module insered into the port.
The value is in units of Mbit/s.
A value of zero means that the transceiver does not insert or unknown type."
::= { fsFiberEntry 89 }
fsFiberFormFactor OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
xfp(1),
sfp(2),
sfpPlus(3),
sfp28(4),
qsfpPlus(5),
qsfp28(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the form factor of the Fiber module insered into the port."
::= { fsFiberEntry 90 }
fsFiberRXpowerLowWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power low warning threshold of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 91 }
fsFiberRXpowerHighWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power high warning threshold of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 92 }
fsFiberRXpowerLowAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power low alarm threshold of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 93 }
fsFiberRXpowerHighAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power high alarm threshold of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 94 }
fsFiberTXpowerLowWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power low warning threshold of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 95 }
fsFiberTXpowerHighWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power high warning threshold of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 96 }
fsFiberTXpowerLowAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power low alarm threshold of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 97 }
fsFiberTXpowerHighAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power high alarm threshold of the Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 98 }
fsFiberChannel5Bias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias in Channel 5 of the QSFP CMIS Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the bias value in Channel 5 is 0."
::= { fsFiberEntry 99 }
fsFiberChannel5BiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias in the Channel 5 of QSFP CMIS is in
the normal level. The status warning(3) indicates
that the bias in the Channel 5 exceeds high warning level or is
below low warning level. The status alarm(4) indicates that the bias in
the Channel 5 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 100 }
fsFiberChannel6Bias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias in Channel 6 of the QSFP CMIS Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the bias value in Channel 6 is 0."
::= { fsFiberEntry 101 }
fsFiberChannel6BiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias in the Channel 6 of QSFP CMIS is in
the normal level. The status warning(3) indicates
that the bias in the Channel 6 exceeds high warning level or is
below low warning level. The status alarm(4) indicates that the bias in
the Channel 6 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 102 }
fsFiberChannel7Bias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias in Channel 7 of the QSFP CMIS Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the bias value in Channel 7 is 0."
::= { fsFiberEntry 103 }
fsFiberChannel7BiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias in the Channel 7 of QSFP CMIS is in
the normal level. The status warning(3) indicates
that the bias in the Channel 7 exceeds high warning level or is
below low warning level. The status alarm(4) indicates that the bias in
the Channel 7 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 104 }
fsFiberChannel8Bias OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias in Channel 8 of the QSFP CMIS Fiber module insered into the port.
The value is in units of uA.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the bias value in Channel 8 is 0."
::= { fsFiberEntry 105 }
fsFiberChannel8BiasStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the bias in the Channel 8 of QSFP CMIS is in
the normal level. The status warning(3) indicates
that the bias in the Channel 8 exceeds high warning level or is
below low warning level. The status alarm(4) indicates that the bias in
the Channel 8 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 106 }
fsFiberChannel5RXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power in Channel 5 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the integer part of Rx power value in Channel 5
is -100(means the value is invalid)."
::= { fsFiberEntry 107 }
fsFiberChannel5RXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power in Channel 5 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the decimal part of Rx power value in Channel 5
is -100(means the value is invalid)."
::= { fsFiberEntry 108 }
fsFiberChannel5RXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3) in Channel 5 of QSFP CMIS.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the value is unknown(1)."
::= { fsFiberEntry 109 }
fsFiberChannel5RXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power in the Channel 5 of QSFP CMIS is in
the normal level. The status warning(3) indicates that
the Rx power in the Channel 5 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Rx power in the
Channel 5 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 110 }
fsFiberChannel6RXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power in Channel 6 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the integer part of Rx power value in Channel 6
is -100(means the value is invalid)."
::= { fsFiberEntry 111 }
fsFiberChannel6RXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power in Channel 6 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the decimal part of Rx power value in Channel 6
is -100(means the value is invalid)."
::= { fsFiberEntry 112 }
fsFiberChannel6RXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3) in Channel 6 of QSFP CMIS.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the value is unknown(1)."
::= { fsFiberEntry 113 }
fsFiberChannel6RXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power in the Channel 6 of QSFP CMIS is in
the normal level. The status warning(3) indicates that
the Rx power in the Channel 6 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Rx power in the
Channel 6 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 114 }
fsFiberChannel7RXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power in Channel 7 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the integer part of Rx power value in Channel 7
is -100(means the value is invalid)."
::= { fsFiberEntry 115 }
fsFiberChannel7RXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power in Channel 7 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the decimal part of Rx power value in Channel 7
is -100(means the value is invalid)."
::= { fsFiberEntry 116 }
fsFiberChannel7RXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3) in Channel 7 of QSFP CMIS.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the value is unknown(1)."
::= { fsFiberEntry 117 }
fsFiberChannel7RXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power in the Channel 7 of QSFP CMIS is in
the normal level. The status warning(3) indicates that
the Rx power in the Channel 7 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Rx power in the
Channel 7 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 118 }
fsFiberChannel8RXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Rx power in Channel 8 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the integer part of Rx power value in Channel 8
is -100(means the value is invalid)."
::= { fsFiberEntry 119 }
fsFiberChannel8RXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Rx power in Channel 8 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the decimal part of Rx power value in Channel 8
is -100(means the value is invalid)."
::= { fsFiberEntry 120 }
fsFiberChannel8RXpowertype OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
average(2),
oma(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value indicates whether the received power measurement
represents average input optical power(2) or oma(3) in Channel 8 of QSFP CMIS.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the value is unknown(1)."
::= { fsFiberEntry 121 }
fsFiberChannel8RXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Rx power in the Channel 8 of QSFP CMIS is in
the normal level. The status warning(3) indicates that
the Rx power in the Channel 8 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Rx power in the
Channel 8 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 122 }
fsFiberChannel5TXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power in Channel 5 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the integer part of Tx power value in Channel 5
is -100(means the value is invalid)."
::= { fsFiberEntry 123 }
fsFiberChannel5TXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power in Channel 5 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the decimal part of Tx power value in Channel 5
is -100(means the value is invalid)."
::= { fsFiberEntry 124 }
fsFiberChannel5TXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power in the Channel 5 of QSFP CMIS is in
the normal level. The status warning(3) indicates that
the Tx power in the Channel 5 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Tx power in the
Channel 5 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 125 }
fsFiberChannel6TXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power in Channel 6 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the integer part of Tx power value in Channel 6
is -100(means the value is invalid)."
::= { fsFiberEntry 126 }
fsFiberChannel6TXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power in Channel 6 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the decimal part of Tx power value in Channel 6
is -100(means the value is invalid)."
::= { fsFiberEntry 127 }
fsFiberChannel6TXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power in the Channel 6 of QSFP CMIS is in
the normal level. The status warning(3) indicates that
the Tx power in the Channel 6 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Tx power in the
Channel 6 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 128 }
fsFiberChannel7TXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power in Channel 7 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the integer part of Tx power value in Channel 7
is -100(means the value is invalid)."
::= { fsFiberEntry 129 }
fsFiberChannel7TXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power in Channel 7 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the decimal part of Tx power value in Channel 7
is -100(means the value is invalid)."
::= { fsFiberEntry 130 }
fsFiberChannel7TXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power in the Channel 7 of QSFP CMIS is in
the normal level. The status warning(3) indicates that
the Tx power in the Channel 7 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Tx power in the
Channel 7 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 131 }
fsFiberChannel8TXpowerIntegerpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer part of Tx power in Channel 8 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the integer part of Tx power value in Channel 8
is -100(means the value is invalid)."
::= { fsFiberEntry 132 }
fsFiberChannel8TXpowerDecimalpart OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The decimal part of Tx power in Channel 8 of the QSFP CMIS
Fiber module insered into the port. The value is in units of dbm.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the decimal part of Tx power value in Channel 8
is -100(means the value is invalid)."
::= { fsFiberEntry 133 }
fsFiberChannel8TXpowerStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
ok(2),
warning(3),
alarm(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status ok(2) indicates that the Tx power in the Channel 8 of QSFP CMIS is in
the normal level. The status warning(3) indicates that
the Tx power in the Channel 8 exceeds high warning level or is below
low warning level. The status alarm(4) indicates that the Tx power in the
Channel 8 exceeds high alarm level or is below low alarm level.
If the fsFiberDDMSupportStatus is false or the Fiber module type is
not QSFP CMIS, the status is unknown(1)."
::= { fsFiberEntry 134 }
fsFiberChannel5RXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 135 }
fsFiberChannel6RXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 136 }
fsFiberChannel7RXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 137 }
fsFiberChannel8RXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 138 }
fsFiberChannel5TXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 139 }
fsFiberChannel6TXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 140 }
fsFiberChannel7TXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 141 }
fsFiberChannel8TXpowerSign OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0."
::= { fsFiberEntry 142 }
fsFiberChannel5RXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power in Channel 5 of the QSFP CMIS Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 143 }
fsFiberChannel6RXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power in Channel 6 of the QSFP CMIS Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 144 }
fsFiberChannel7RXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power in Channel 7 of the QSFP CMIS Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 145 }
fsFiberChannel8RXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power in Channel 8 of the QSFP CMIS Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 146 }
fsFiberChannel5TXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power in Channel 5 of the QSFP CMIS Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 147 }
fsFiberChannel6TXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power in Channel 6 of the QSFP CMIS Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 148 }
fsFiberChannel7TXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power in Channel 7 of the QSFP CMIS Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 149 }
fsFiberChannel8TXpower OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power in Channel 8 of the QSFP CMIS Fiber module insered into the port.
The value is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 150 }
fsFiberTransferDistance50umOM5 OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using 50 micron multimode OM5(4700 MHz*Km at 850nm, 2470 MHz*km at 953nm) fiber.
The value is in units of meters.
A value of zero means that the transceiver does not
support 50 micron multimode fiber or the Fiber module type
is neither SFP/SFP+ nor QSFP+."
::= { fsFiberEntry 151 }
fsFiberMode OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
copper(1),
singleMode(2),
multiMode(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the fiber type."
::= { fsFiberEntry 152 }
fsFiberTempLowWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The temperature low warning threshold of the Fiber module insered into the port.
The value is in units of degrees Celsius.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 153 }
fsFiberTempHighWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The temperature high warning threshold of the Fiber module insered into the port.
The value is in units of degrees Celsius.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 154 }
fsFiberTempLowAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The temperature low alarm threshold of the Fiber module insered into the port.
The value is in units of degrees Celsius.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 155 }
fsFiberTempHighAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The temperature high alarm threshold of the Fiber module insered into the port.
The value is in units of degrees Celsius.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 156 }
fsFiberVoltageLowWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The voltage low warning threshold of the Fiber module insered into the port.
The value is in units of mVolts.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 157 }
fsFiberVoltageHighWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The voltage high warning threshold of the Fiber module insered into the port.
The value is in units of mVolts.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 158 }
fsFiberVoltageLowAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The voltage low alarm threshold of the Fiber module insered into the port.
The value is in units of mVolts.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 159 }
fsFiberVoltageHighAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The voltage high alarm threshold of the Fiber module insered into the port.
The value is in units of mVolts.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 160 }
fsFiberBiasLowWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias low warning threshold of the Fiber module insered into the port.
The value is in units of uA.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 161 }
fsFiberBiasHighWarnThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias high warning threshold of the Fiber module insered into the port.
The value is in units of uA.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 162 }
fsFiberBiasLowAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias low alarm threshold of the Fiber module insered into the port.
The value is in units of uA.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 163 }
fsFiberBiasHighAlarmThreshold OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bias high alarm threshold of the Fiber module insered into the port.
The value is in units of uA.
The value of -10000 means the value is invalid."
::= { fsFiberEntry 164 }
fsFiberVendorTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSFiberVendorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Vendor info entries."
::= { fsFiberMIBObjects 2 }
fsFiberVendorEntry OBJECT-TYPE
SYNTAX FSFiberVendorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry contains Vendor info."
INDEX { fsFiberVendorPortIndex }
::= { fsFiberVendorTable 1 }
FSFiberVendorEntry ::=
SEQUENCE {
fsFiberVendorPortIndex IfIndex,
fsFiberVendorName DisplayString,
fsFiberVendorOUI DisplayString,
fsFiberVendorPartNumber DisplayString,
fsFiberVendorRev DisplayString,
fsFiberManufacturingDate DisplayString,
fsFiberEncoding DisplayString
}
fsFiberVendorPortIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The port index of Vendor info ."
::= { fsFiberVendorEntry 1 }
fsFiberVendorName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The description of vendor name."
::= { fsFiberVendorEntry 2 }
fsFiberVendorOUI OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The description of vendor oui."
::= { fsFiberVendorEntry 3 }
fsFiberVendorPartNumber OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The description of vendor part number."
::= { fsFiberVendorEntry 4 }
fsFiberVendorRev OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The description of vendor revision."
::= { fsFiberVendorEntry 5 }
fsFiberManufacturingDate OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The description of vendor's manufacturing date."
::= { fsFiberVendorEntry 6 }
fsFiberEncoding OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The description of vendor's encoding type."
::= { fsFiberVendorEntry 7 }
fsFiberOMCTable OBJECT-TYPE
SYNTAX SEQUENCE OF FSFiberOMCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OMC fiber info entries."
::= { fsFiberMIBObjects 3 }
fsFiberOMCEntry OBJECT-TYPE
SYNTAX FSFiberOMCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry contains OMC fiber info."
INDEX { fsFiberOMCPortIndex }
::= { fsFiberOMCTable 1 }
FSFiberOMCEntry ::=
SEQUENCE {
fsFiberOMCPortIndex IfIndex,
fsFiberOMCRxpower DisplayString,
fsFiberOMCTxpower DisplayString,
fsFiberOMCWavelength DisplayString,
fsFiberOMCTranslength DisplayString,
fsFiberOMCPortType DisplayString
}
fsFiberOMCPortIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Port index of the port."
::= { fsFiberOMCEntry 1 }
fsFiberOMCRxpower OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Rx power of the Fiber module insered into the port.
Use a comma to separate multiple optical power values for multiple channels,
fill in key-value pairs, connect the key and value with an equal sign,
the key is the channel name, and the value is the optical power.
The unit of the optical power value is dbw."
::= { fsFiberOMCEntry 2 }
fsFiberOMCTxpower OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Tx power of the Fiber module insered into the port.
Use a comma to separate multiple optical power values for multiple channels,
fill in key-value pairs, connect the key and value with an equal sign,
the key is the channel name, and the value is the optical power.
The unit of the optical power value is dbw."
::= { fsFiberOMCEntry 3 }
fsFiberOMCWavelength OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of wavelength of the Fiber module insered into the port.
The unit is nm.
If it is a single wavelength, report a single value, for example: 1310.
If it is a wavelength range, report the wavelength range, for example: 1310-1312.
The reported string does not include the unit."
::= { fsFiberOMCEntry 4 }
fsFiberOMCTranslength OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of transfer distance of the Fiber module insered into the port.
The unit is km.
If it is a single distance, report a single value, for example: 20
If there are multiple distances in fiber mode, report multiple sets of data separated by commas.
The format of each group of data is a key-value pair, the key and value are connected with =,
the key is the fiber grade, and the value is the corresponding distance, such as 'OM1=20, OM2=30'"
::= { fsFiberOMCEntry 5 }
fsFiberOMCPortType OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Port type of the Fiber module insered into the port."
::= { fsFiberOMCEntry 6 }
fsFiberAntifakeMIBTraps OBJECT IDENTIFIER ::= { fsFiberMIB 2 }
fsFiberAntifakeIntfNameDesc OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..255))
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The description of the interface."
::= { fsFiberAntifakeMIBTraps 1 }
fsFiberAntifakeSerialNumberDesc OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..255))
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The description of the serial number of the fiber module."
::= { fsFiberAntifakeMIBTraps 2 }
fsFiberAntifakeTrap NOTIFICATION-TYPE
OBJECTS {fsFiberAntifakeIntfNameDesc, fsFiberAntifakeSerialNumberDesc}
STATUS current
DESCRIPTION
"When detect the fiber module is not original fs fiber module, then this trap will be sent."
::= { fsFiberAntifakeMIBTraps 3 }
fsFiberMIBConformance OBJECT IDENTIFIER ::= { fsFiberMIB 3 }
fsFiberMIBCompliances OBJECT IDENTIFIER ::= { fsFiberMIBConformance 1 }
fsFiberMIBGroups OBJECT IDENTIFIER ::= { fsFiberMIBConformance 2 }
fsFiberEventMIBTraps OBJECT IDENTIFIER ::= { fsFiberMIB 4 }
fsFiberEventReason OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
fiberInvalidTxHigh(2),
fiberInvalidTxLow(3),
fiberInvalidRxHigh(4),
fiberInvalidRxLow(5),
fiberInvalidI2CFail(6),
fiberInvalidNotSupp(7),
fiberInvalidTemperatureLow(8),
fiberInvalidTemperatureHigh(9),
fiberInvalidVoltageLow(10),
fiberInvalidVoltageHigh(11),
fiberInvalidTXBiasLow(12),
fiberInvalidTXBiasHigh(13),
fiberInvalidRXLossSignal(14),
fiberInvalidRXCDRLossLock(15),
fiberInvalidTXLossSignal(16),
fiberInvalidTXCDRLossLock(17),
fiberInvalidTXFault(18),
fiberInvalidCheckSumError(19),
fiberInvalidModuleNotReady(20),
fiberInvalidRXNotReady(21),
fiberInvalidTxHighWarn(22),
fiberInvalidTxLowWarn(23),
fiberInvalidRxHighWarn(24),
fiberInvalidRxLowWarn(25),
fiberInvalidTemperatureLowWarn(26),
fiberInvalidTemperatureHighWarn(27),
fiberInvalidVoltageLowWarn(28),
fiberInvalidVoltageHighWarn(29),
fiberInvalidTXBiasLowWarn(30),
fiberInvalidTXBiasHighWarn(31),
fiberInvalidRXTotalPowerLowAlarm(32),
fiberInvalidRXMediaPreFECBERHighAlarm(33),
fiberInvalidColorGrayFiberAlarm(34),
fiberInvalidRXTotalPowerLowWarn(35),
fiberInvalidRXMediaPreFECBERHighWarn(36)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The reason of the fiber invalid event."
::= { fsFiberEventMIBTraps 1 }
fsFiberEventDesc OBJECT-TYPE
SYNTAX DisplayString (SIZE(0..255))
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The description of the fiber invalid event."
::= { fsFiberEventMIBTraps 2 }
fsFiberRemoveEventTrap NOTIFICATION-TYPE
OBJECTS {ifIndex, ifDescr}
STATUS current
DESCRIPTION
"When detect the fiber has been removed, then this trap will be sent."
::= { fsFiberEventMIBTraps 3 }
fsFiberInsertEventTrap NOTIFICATION-TYPE
OBJECTS {ifIndex, ifDescr}
STATUS current
DESCRIPTION
"When detect the fiber has been inserted, then this trap will be sent."
::= { fsFiberEventMIBTraps 4 }
fsFiberInvalidTrap NOTIFICATION-TYPE
OBJECTS {ifIndex, ifDescr, fsFiberEventReason, fsFiberEventDesc, fsFiberAlarmValue, fsFiberAlarmThresholdValue}
STATUS current
DESCRIPTION
"Detect the fiber invalid event."
::= { fsFiberEventMIBTraps 5 }
fsFiberInvalidResumeTrap NOTIFICATION-TYPE
OBJECTS {ifIndex, ifDescr, fsFiberEventReason, fsFiberEventDesc, fsFiberAlarmValue, fsFiberAlarmThresholdValue}
STATUS current
DESCRIPTION
"The fiber resume from invalid event."
::= { fsFiberEventMIBTraps 6 }
fsFiberAlarmValue OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The realtime value of the fiber invalid event. The value of power is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEventMIBTraps 7 }
fsFiberAlarmThresholdValue OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The threshold value of the fiber invalid event. The value of power is in units of dbm, which needs to be divided by 100.
The value of -10000 means the value is invalid."
::= { fsFiberEventMIBTraps 8 }
fsFiberSpeedMismatch NOTIFICATION-TYPE
OBJECTS { ifIndex, ifDescr }
STATUS current
DESCRIPTION
"When detect the fiber has been inserted and the speed of the optical module does not match
the speed supported by the interface, then this trap will be sent."
::= { fsFiberEventMIBTraps 9 }
-- ---------------------------------------------------------- --
-- compliance statements
-- ---------------------------------------------------------- --
fsFiberMIBConpliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for entities which implement
the FS Fiber MIB"
MODULE -- this module
MANDATORY-GROUPS {
fsFiberMIBGroup
}
GROUP fsFiberAntifakeIntfNameDescGroup
DESCRIPTION
"This group is mandatory only for those system which support fiber antifake notification."
GROUP fsFiberAntifakeSerialNumberDescGroup
DESCRIPTION
"This group is mandatory only for those system which support fiber antifake notification."
::= { fsFiberMIBCompliances 1 }
fsFiberMIBGroup OBJECT-GROUP
OBJECTS {
fsFiberPortDescr,
fsFiberTransceiverType,
fsFiberConnectorType,
fsFiberWavelength,
fsFiberTransferDistanceSMF,
fsFiberTransferDistance62point5umOM1,
fsFiberTransferDistance62point5um,
fsFiberTransferDistance50umOM2,
fsFiberTransferDistance50um,
fsFiberTransferDistance50umOM3,
fsFiberTransferDistanceEBW50um,
fsFiberTransferDistanceCopper,
fsFiberTransferDistanceCableAssembly,
fsFiberDDMSupportStatus,
fsFiberSerialNumber,
fsFiberTemp,
fsFiberTempStatus,
fsFiberVoltage,
fsFiberVoltageStatus,
fsFiberBias,
fsFiberBiasStatus,
fsFiberChannel1Bias,
fsFiberChannel1BiasStatus,
fsFiberChannel2Bias,
fsFiberChannel2BiasStatus,
fsFiberChannel3Bias,
fsFiberChannel3BiasStatus,
fsFiberChannel4Bias,
fsFiberChannel4BiasStatus,
fsFiberRXpowerIntegerpart,
fsFiberRXpowerDecimalpart,
fsFiberRXpowertype,
fsFiberRXpowerStatus,
fsFiberChannel1RXpowerIntegerpart,
fsFiberChannel1RXpowerDecimalpart,
fsFiberChannel1RXpowertype,
fsFiberChannel1RXpowerStatus,
fsFiberChannel2RXpowerIntegerpart,
fsFiberChannel2RXpowerDecimalpart,
fsFiberChannel2RXpowertype,
fsFiberChannel2RXpowerStatus,
fsFiberChannel3RXpowerIntegerpart,
fsFiberChannel3RXpowerDecimalpart,
fsFiberChannel3RXpowertype,
fsFiberChannel3RXpowerStatus,
fsFiberChannel4RXpowerIntegerpart,
fsFiberChannel4RXpowerDecimalpart,
fsFiberChannel4RXpowertype,
fsFiberChannel4RXpowerStatus,
fsFiberTXpowerIntegerpart,
fsFiberTXpowerDecimalpart,
fsFiberTXpowerStatus,
fsFiberChannel1TXpowerIntegerpart,
fsFiberChannel1TXpowerDecimalpart,
fsFiberChannel1TXpowerStatus,
fsFiberChannel2TXpowerIntegerpart,
fsFiberChannel2TXpowerDecimalpart,
fsFiberChannel2TXpowerStatus,
fsFiberChannel3TXpowerIntegerpart,
fsFiberChannel3TXpowerDecimalpart,
fsFiberChannel3TXpowerStatus,
fsFiberChannel4TXpowerIntegerpart,
fsFiberChannel4TXpowerDecimalpart,
fsFiberChannel4TXpowerStatus,
fsFiberRXpowerSign,
fsFiberChannel1RXpowerSign,
fsFiberChannel2RXpowerSign,
fsFiberChannel3RXpowerSign,
fsFiberChannel4RXpowerSign,
fsFiberTXpowerSign,
fsFiberChannel1TXpowerSign,
fsFiberChannel2TXpowerSign,
fsFiberChannel3TXpowerSign,
fsFiberChannel4TXpowerSign,
fsFiberRXpower,
fsFiberChannel1RXpower,
fsFiberChannel2RXpower,
fsFiberChannel3RXpower,
fsFiberChannel4RXpower,
fsFiberTXpower,
fsFiberChannel1TXpower,
fsFiberChannel2TXpower,
fsFiberChannel3TXpower,
fsFiberChannel4TXpower,
fsFiberWavelengthExact,
fsFiberTransferDistance50umOM4,
fsFiberTransferDistanceSMFExt,
fsFiberBandWidth,
fsFiberFormFactor,
fsFiberRXpowerLowWarnThreshold,
fsFiberRXpowerHighWarnThreshold,
fsFiberRXpowerLowAlarmThreshold,
fsFiberRXpowerHighAlarmThreshold,
fsFiberTXpowerLowWarnThreshold,
fsFiberTXpowerHighWarnThreshold,
fsFiberTXpowerLowAlarmThreshold,
fsFiberTXpowerHighAlarmThreshold,
fsFiberChannel5Bias,
fsFiberChannel5BiasStatus,
fsFiberChannel6Bias,
fsFiberChannel6BiasStatus,
fsFiberChannel7Bias,
fsFiberChannel7BiasStatus,
fsFiberChannel8Bias,
fsFiberChannel8BiasStatus,
fsFiberChannel5RXpowerIntegerpart,
fsFiberChannel5RXpowerDecimalpart,
fsFiberChannel5RXpowertype,
fsFiberChannel5RXpowerStatus,
fsFiberChannel6RXpowerIntegerpart,
fsFiberChannel6RXpowerDecimalpart,
fsFiberChannel6RXpowertype,
fsFiberChannel6RXpowerStatus,
fsFiberChannel7RXpowerIntegerpart,
fsFiberChannel7RXpowerDecimalpart,
fsFiberChannel7RXpowertype,
fsFiberChannel7RXpowerStatus,
fsFiberChannel8RXpowerIntegerpart,
fsFiberChannel8RXpowerDecimalpart,
fsFiberChannel8RXpowertype,
fsFiberChannel8RXpowerStatus,
fsFiberChannel5TXpowerIntegerpart,
fsFiberChannel5TXpowerDecimalpart,
fsFiberChannel5TXpowerStatus,
fsFiberChannel6TXpowerIntegerpart,
fsFiberChannel6TXpowerDecimalpart,
fsFiberChannel6TXpowerStatus,
fsFiberChannel7TXpowerIntegerpart,
fsFiberChannel7TXpowerDecimalpart,
fsFiberChannel7TXpowerStatus,
fsFiberChannel8TXpowerIntegerpart,
fsFiberChannel8TXpowerDecimalpart,
fsFiberChannel8TXpowerStatus,
fsFiberChannel5RXpowerSign,
fsFiberChannel6RXpowerSign,
fsFiberChannel7RXpowerSign,
fsFiberChannel8RXpowerSign,
fsFiberChannel5TXpowerSign,
fsFiberChannel6TXpowerSign,
fsFiberChannel7TXpowerSign,
fsFiberChannel8TXpowerSign,
fsFiberChannel5RXpower,
fsFiberChannel6RXpower,
fsFiberChannel7RXpower,
fsFiberChannel8RXpower,
fsFiberChannel5TXpower,
fsFiberChannel6TXpower,
fsFiberChannel7TXpower,
fsFiberChannel8TXpower,
fsFiberTransferDistance50umOM5,
fsFiberMode,
fsFiberTempLowWarnThreshold,
fsFiberTempHighWarnThreshold,
fsFiberTempLowAlarmThreshold,
fsFiberTempHighAlarmThreshold,
fsFiberVoltageLowWarnThreshold,
fsFiberVoltageHighWarnThreshold,
fsFiberVoltageLowAlarmThreshold,
fsFiberVoltageHighAlarmThreshold,
fsFiberBiasLowWarnThreshold,
fsFiberBiasHighWarnThreshold,
fsFiberBiasLowAlarmThreshold,
fsFiberBiasHighAlarmThreshold
}
STATUS current
DESCRIPTION
"A collection of objects providing Fiber managment."
::= { fsFiberMIBGroups 1 }
fsFiberAntifakeIntfNameDescGroup OBJECT-GROUP
OBJECTS {fsFiberAntifakeIntfNameDesc}
STATUS current
DESCRIPTION
"Objects that providing a literal description of the interface."
::= { fsFiberMIBGroups 2 }
fsFiberAntifakeSerialNumberDescGroup OBJECT-GROUP
OBJECTS {fsFiberAntifakeSerialNumberDesc}
STATUS current
DESCRIPTION
"Objects that providing a literal description of the fiber module serial number."
::= { fsFiberMIBGroups 3 }
END