mibs/hp/HP-ICF-RATE-LIMIT-MIB
HP-ICF-RATE-LIMIT-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Integer32
FROM SNMPv2-SMI
InterfaceIndex, ifIndex
FROM IF-MIB
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
hpicfObjectModules, hpicfRateLimitTrapsPrefix
FROM HP-ICF-OID
;
hpicfRateLimitMIB MODULE-IDENTITY
LAST-UPDATED "200708291120Z" -- August 29, 2007
ORGANIZATION "Hewlett Packard Company,
Procurve Networking Business"
CONTACT-INFO "Hewlett Packard Company
8000 Foothills Blvd.
Roseville, CA 95747"
DESCRIPTION "This MIB module describes HP rate limit information."
REVISION "200708291120Z" -- August 29, 2007
DESCRIPTION "Deprecated all bps objects for
hpEgressRateLimitPortConfigTable and
hpIngressRateLimitPortConfigTable, and updated
compliance information (including correcting ICMP
group to be hpICMPRateLimitPortConfigGroup2)."
REVISION "200707271920Z" -- July 27, 2007
DESCRIPTION "Modified enumerated type names for
hpICMPRateLimitPortControlMode object."
REVISION "200706011146Z" -- June 1, 2007
DESCRIPTION "Deprecated hpICMPRateLimitPortState in favor of new
hpICMPRateLimitPortControlMode object."
REVISION "200705301610Z" -- May 30, 2007
DESCRIPTION "Added Kbps configuration for ICMP, port-egress,
and port-ingress rate-limiting definitions."
REVISION "200607071833Z" -- July 07, 2006
DESCRIPTION "Added new egress rate limiting bps objects, and
ingress rate-limiting definitions."
REVISION "200504201130Z" -- April 20, 2005
DESCRIPTION "Added minimum bandwidth and egress rate limiting
definitions."
REVISION "200408221030Z" -- August 22, 2004
DESCRIPTION "Initial version."
::= { hpicfObjectModules 14 }
hpicfRateLimitObjects OBJECT IDENTIFIER ::= { hpicfRateLimitMIB 1 }
-- ICMP Rate Limiting Objects
hpicfICMPRateLimitObjects OBJECT IDENTIFIER ::= { hpicfRateLimitObjects 1 }
hpICMPRateLimitConfig OBJECT IDENTIFIER ::= { hpicfICMPRateLimitObjects 1 }
hpICMPRateLimitPortConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpICMPRateLimitPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table that contains configuration objects on ICMP
rate limit on a per interface basis."
::= { hpICMPRateLimitConfig 1 }
hpICMPRateLimitPortConfigEntry OBJECT-TYPE
SYNTAX HpICMPRateLimitPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Entry that contains configuration objects on ICMP
rate limit on a per interface basis"
INDEX { hpICMPRateLimitPortConfigIndex }
::= { hpICMPRateLimitPortConfigTable 1 }
HpICMPRateLimitPortConfigEntry ::=
SEQUENCE {
hpICMPRateLimitPortConfigIndex InterfaceIndex,
hpICMPRateLimitPortState INTEGER,
hpICMPRateLimitPortPrct Integer32,
hpICMPRateLimitPortAlarmFlag INTEGER,
hpICMPRateLimitPortKbps Integer32,
hpICMPRateLimitPortControlMode INTEGER
}
hpICMPRateLimitPortConfigIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The interface index associated with this entry."
::= { hpICMPRateLimitPortConfigEntry 1 }
hpICMPRateLimitPortState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION "This object indicates whether ICMP rate limiting is
enabled on the corresponding port.
Because this is a State object it cannot distinguish
between percent-based ICMP Rate-Limiting and the newer
Kbps-based ICMP Rate-Limiting. Therefore, it has been
deprecated in favor of hpICMPRateLimitPortControlMode."
DEFVAL { disabled }
::= { hpICMPRateLimitPortConfigEntry 2 }
hpICMPRateLimitPortPrct OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This indicates the percent of ICMP rate limit on
the port. The value of this object must be
interpreted under the context of
hpICMPRateLimitPortState. A value of 0 is not the
same as disabling, but rather all ICMP traffic must
be dropped."
::= { hpICMPRateLimitPortConfigEntry 3 }
hpICMPRateLimitPortAlarmFlag OBJECT-TYPE
SYNTAX INTEGER {
clear(1),
set(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This object indicates whether ICMP rate limiting
alarm has been sent. When an alarm is sent, this
object is set to set(2). Once a management station
changes this object to clear(1), an alarm can be
sent again for this port."
DEFVAL { clear }
::= { hpICMPRateLimitPortConfigEntry 4 }
hpICMPRateLimitPortKbps OBJECT-TYPE
SYNTAX Integer32 (0..10000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The maximum Kilobits-per-second of ICMP traffic that may
be received inbound on the port. The value of this
object must be interpreted under the context of
hpICMPRateLimitControlMode. A value of 0 is not the
same as disabling, but means instead that all ICMP
traffic must be dropped."
::= { hpICMPRateLimitPortConfigEntry 5 }
hpICMPRateLimitPortControlMode OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
portPrct(2),
portKbps(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The mode by which inbound ICMP traffic on this port will
Rate-Limited. If icmpRateLimitPerPortOnly is configured,
there will be a single maximum percentage-based rate for
the entire port. If icmpRateLimitPerPortOnlyKbpsMode is
configured, there will be a single maximum kilobits-per-
second rate for the entire port. When ICMP rate-limiting
is disabled, there are no maximum controls on inbound
ICMP traffic for this port."
DEFVAL { disabled }
::= { hpICMPRateLimitPortConfigEntry 6 }
hpICMPRateLimitPortNotification NOTIFICATION-TYPE
OBJECTS { hpICMPRateLimitNotifyPortIndex }
STATUS current
DESCRIPTION "This notification indicates limit has exceeded."
::= { hpicfRateLimitTrapsPrefix 1 }
hpICMPRateLimitNotifyPortIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION "The interface index associated with
hpICMPRateLimitPortNotification event."
::= { hpicfICMPRateLimitObjects 2 }
-- Egress Minimum Bandwidth Ojbects
hpicfBWMinEgressObjects OBJECT IDENTIFIER ::=
{ hpicfRateLimitObjects 2 }
hpBWMinEgressPortConfig OBJECT IDENTIFIER ::=
{ hpicfBWMinEgressObjects 1 }
hpBWMinEgressPortNumQueues OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of bandwidth minimum egress queues supported
on this system."
::= { hpBWMinEgressPortConfig 1 }
hpBWMinEgressPortPrctTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpBWMinEgressPortPrctEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table that contains information about the port's egress
Guaranteed Minimum Bandwidth percent configurations on
this switch. The number of entries in this table is
determined by hpBWMinEgressPortNumQueues. The priority of
the queues is in ascending order, starting with queue one
being the lowest and queue hpBWMinEgressPortNumQueues
being the highest."
::= { hpBWMinEgressPortConfig 2 }
hpBWMinEgressPortPrctEntry OBJECT-TYPE
SYNTAX HpBWMinEgressPortPrctEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The information associated with each port's egress
Guaranteed Minimum Bandwidth percent configuration."
INDEX { ifIndex, hpBWMinEgressPortPrctQueue }
::= { hpBWMinEgressPortPrctTable 1 }
HpBWMinEgressPortPrctEntry ::=
SEQUENCE {
hpBWMinEgressPortPrctQueue Integer32,
hpBWMinEgressPortPrct Integer32
}
hpBWMinEgressPortPrctQueue OBJECT-TYPE
SYNTAX Integer32 (1..9000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The queue associated with this entry. The priority of
the queues is in ascending order, starting with queue one
being the lowest and queue hpBWMinEgressPortNumQueues
being the highest."
::= { hpBWMinEgressPortPrctEntry 1 }
hpBWMinEgressPortPrct OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The percentage of Guaranteed Minimum bandwidth to be
assigned to this egress queue for this port. Total values
for all queues must not exceed 100 percent."
::= { hpBWMinEgressPortPrctEntry 2 }
-- Ingress Minimum Bandwidth Ojbects
hpicfBWMinIngressObjects OBJECT IDENTIFIER ::=
{ hpicfRateLimitObjects 3 }
hpBWMinIngressPortConfig OBJECT IDENTIFIER ::=
{ hpicfBWMinIngressObjects 1 }
hpBWMinIngressPortNumQueues OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of bandwidth minimum ingress queues supported
on this system."
::= { hpBWMinIngressPortConfig 1 }
hpBWMinIngressPortPrctTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpBWMinIngressPortPrctEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table that contains information about the port's
ingress Guaranteed Minimum Bandwidth percent
configurations on this switch. The number of entries in
this table is determined by hpBWMinIngressPortNumQueues.
The priority of the queues is in ascending order, starting
with queue one being the lowest and queue
hpBWMinIngressPortNumQueues being the highest."
::= { hpBWMinIngressPortConfig 2 }
hpBWMinIngressPortPrctEntry OBJECT-TYPE
SYNTAX HpBWMinIngressPortPrctEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The information associated with each port's ingress
Guaranteed Minimum Bandwidth percent configuration."
INDEX { ifIndex, hpBWMinIngressPortPrctQueue }
::= { hpBWMinIngressPortPrctTable 1 }
HpBWMinIngressPortPrctEntry ::=
SEQUENCE {
hpBWMinIngressPortPrctQueue Integer32,
hpBWMinIngressPortPrct Integer32
}
hpBWMinIngressPortPrctQueue OBJECT-TYPE
SYNTAX Integer32 (1..9000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The queue associated with this entry. The priority of
the queues is in ascending order, starting with queue one
being the lowest and queue hpBWMinIngressPortNumQueues
being the highest."
::= { hpBWMinIngressPortPrctEntry 1 }
hpBWMinIngressPortPrct OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The percentage of Guaranteed Minimum bandwidth to be
assigned to this ingress queue for this port. Total values
for all queues must not exceed 100 percent."
::= { hpBWMinIngressPortPrctEntry 2 }
-- Egress Rate Limiting Objects
hpicfRateLimitPortObjects OBJECT IDENTIFIER ::=
{ hpicfRateLimitObjects 4 }
hpRateLimitPortConfig OBJECT IDENTIFIER ::=
{ hpicfRateLimitPortObjects 1 }
hpEgressRateLimitPortNumQueues OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of egress rate-limiting queues supported on
this system."
::= { hpRateLimitPortConfig 1 }
hpEgressRateLimitPortConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpEgressRateLimitPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table that contains information about the port egress
Rate-Limiting configurations on this switch."
::= { hpRateLimitPortConfig 2 }
hpEgressRateLimitPortConfigEntry OBJECT-TYPE
SYNTAX HpEgressRateLimitPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The information associated with each port's egress
Rate-Limiting configuration."
INDEX { hpEgressRateLimitPortIndex }
::= { hpEgressRateLimitPortConfigTable 1 }
HpEgressRateLimitPortConfigEntry ::=
SEQUENCE {
hpEgressRateLimitPortIndex InterfaceIndex,
hpEgressRateLimitPortControlMode INTEGER,
hpEgressRateLimitPortSingleControlPrct Integer32,
hpEgressRateLimitPortSingleControlBps Unsigned32,
hpEgressRateLimitPortSingleControlKbps Integer32
}
hpEgressRateLimitPortIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The ifIndex value which uniquely identifies a row in the
Interfaces Table."
::= { hpEgressRateLimitPortConfigEntry 1 }
hpEgressRateLimitPortControlMode OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
egressRateLimitPerPortOnly(2),
egressRateLimitPerQueue(3),
egressRateLimitPerPortOnlyBpsMode(4),
egressRateLimitPerQueueBpsMode(5),
egressRateLimitPerPortOnlyKbpsMode(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The mode by which this port will be Rate-Limited on
egress. If egressRateLimitPerPortOnly is configured, there
will be a single maximum percentage-based rate for the
entire port. If egressRateLimitPerQueue is configured, the
values for each of the queues indicate the maximum
percentage of port traffic that may be transmitted by that
queue. If egressRateLimitPerPortOnlyBpsMode is configured,
there will be a single maximum bits-per-second rate for
the entire port. If egressRateLimitPerPortOnlyKbpsMode is
configured, there will be a single maximum
kilobits-per-second rate for the entire port. If
egressRateLimitPerQueueBpsMode is configured, the maximum
transmission-rate values for each of the queues will be
expressed in bits-per-second (again, the sum of these
values must not exceed the maximum Bytes-per-second
capability of the network link). The queues are defined
under hpEgressRateLimitPortPrctTable. When egress
rate-limiting is disabled, there are no maximum controls
on egress for this port."
DEFVAL { disabled }
::= { hpEgressRateLimitPortConfigEntry 2 }
hpEgressRateLimitPortSingleControlPrct OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "When hpEgressRateLimitPortControlMode is configured
for egressRateLimitPerPortOnly, this value is the maximum
percentage of traffic that may be transmitted by this
port on egress."
::= { hpEgressRateLimitPortConfigEntry 3 }
hpEgressRateLimitPortSingleControlBps OBJECT-TYPE
SYNTAX Unsigned32 (0..4200000000)
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION "When hpEgressRateLimitPortControlMode is configured for
egressRateLimitPerPortOnlyBpsMode, this value is the
maximum bits-per-second of traffic that may be transmitted
by this port on egress."
::= { hpEgressRateLimitPortConfigEntry 4 }
hpEgressRateLimitPortSingleControlKbps OBJECT-TYPE
SYNTAX Integer32 (0..10000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "When hpEgressRateLimitPortControlMode is configured for
egressRateLimitPerPortOnlyKbpsMode, this value is the
maximum kilobits-per-second of traffic that may be
transmitted by this port on egress."
::= { hpEgressRateLimitPortConfigEntry 5 }
hpEgressRateLimitPortPrctTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpEgressRateLimitPortPrctEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table that contains information about the port egress
Rate-Limiting percent configurations on this switch. The
number of entries in this table is determined by
hpEgressRateLimitPortNumQueues. The priority of the
queues is in ascending order, starting with queue one
being the lowest priority and queue
hpEgressRateLimitPortNumQueues being the highest
priority."
::= { hpRateLimitPortConfig 3 }
hpEgressRateLimitPortPrctEntry OBJECT-TYPE
SYNTAX HpEgressRateLimitPortPrctEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The information associated with each port's egress
Rate-Limiting percent configuration."
INDEX { hpEgressRateLimitPortIndex,
hpEgressRateLimitPortPrctQueue }
::= { hpEgressRateLimitPortPrctTable 1 }
HpEgressRateLimitPortPrctEntry ::=
SEQUENCE {
hpEgressRateLimitPortPrctQueue Integer32,
hpEgressRateLimitPortPrct Integer32
}
hpEgressRateLimitPortPrctQueue OBJECT-TYPE
SYNTAX Integer32 (1..9000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The queue associated with this entry. The priority o
of the queues is in ascending order, starting with
queue one being the lowest and queue
hpEgressRateLimitgressPortNumQueues being the highest."
::= { hpEgressRateLimitPortPrctEntry 1 }
hpEgressRateLimitPortPrct OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The maximum percentage of traffic that may be
transmitted by this port's queue on egress.
hpEgressRateLimitPortControlMode must be configured to
use egressRateLimitPerQueue for this to take effect. A
value of 0-percent for any queue means that no traffic
will ever be transmitted on this port for that egress
queue."
::= { hpEgressRateLimitPortPrctEntry 2 }
hpEgressRateLimitPortBpsTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpEgressRateLimitPortBpsEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION "A table that contains information about the port
egress Rate-Limiting bits-per-second configurations on this
switch. The number of entries in this table is determined
by hpEgressRateLimitPortNumQueues. The priority of the
queues is in ascending order, starting with queue one
being the lowest priority and queue
hpEgressRateLimitPortNumQueues being the highest
priority queue."
::= { hpRateLimitPortConfig 4 }
hpEgressRateLimitPortBpsEntry OBJECT-TYPE
SYNTAX HpEgressRateLimitPortBpsEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION "The information associated with each port's egress
Rate-Limiting bits-per-second configuration."
INDEX { hpEgressRateLimitPortIndex,
hpEgressRateLimitPortBpsQueue }
::= { hpEgressRateLimitPortBpsTable 1 }
HpEgressRateLimitPortBpsEntry ::=
SEQUENCE {
hpEgressRateLimitPortBpsQueue Integer32,
hpEgressRateLimitPortBps Unsigned32
}
hpEgressRateLimitPortBpsQueue OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION "The queue associated with this entry. The priority of
the queues is in ascending order, starting with queue one
being the lowest and queue
hpEgressRateLimitgressPortNumQueues being the highest."
::= { hpEgressRateLimitPortBpsEntry 1 }
hpEgressRateLimitPortBps OBJECT-TYPE
SYNTAX Unsigned32 (0..4200000000)
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION "The maximum bits-per-second of traffic that may be
transmitted by this port's queue on egress.
hpEgressRateLimitPortControlMode must be configured to use
egressRateLimitPerQueue for this to take effect. A value
of 0-percent for any queue means that no traffic will ever
be transmitted on this port for that egress queue. The
values for each queue must not exceed the bits-per-second
capability of the current network link speed."
::= { hpEgressRateLimitPortBpsEntry 2 }
-- Ingress Rate Limiting Objects
hpicfIngressRateLimitPortObjects OBJECT IDENTIFIER ::=
{ hpicfRateLimitObjects 5 }
hpRateLimitIngressPortConfig OBJECT IDENTIFIER ::=
{ hpicfIngressRateLimitPortObjects 1 }
hpIngressRateLimitPortNumQueues OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of ingress rate-limiting queues supported on
this system."
::= { hpRateLimitIngressPortConfig 1 }
hpIngressRateLimitPortConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpIngressRateLimitPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table that contains information about the port ingress
Rate-Limiting configurations on this switch."
::= { hpRateLimitIngressPortConfig 2 }
hpIngressRateLimitPortConfigEntry OBJECT-TYPE
SYNTAX HpIngressRateLimitPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The information associated with each port's ingress
Rate-Limiting configuration."
INDEX { hpIngressRateLimitPortIndex }
::= { hpIngressRateLimitPortConfigTable 1 }
HpIngressRateLimitPortConfigEntry ::=
SEQUENCE {
hpIngressRateLimitPortIndex InterfaceIndex,
hpIngressRateLimitPortControlMode INTEGER,
hpIngressRateLimitPortSingleControlPrct Integer32,
hpIngressRateLimitPortSingleControlBps Unsigned32,
hpIngressRateLimitPortSingleControlKbps Integer32
}
hpIngressRateLimitPortIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The ifIndex value which uniquely identifies a row in the
Interfaces Table."
::= { hpIngressRateLimitPortConfigEntry 1 }
hpIngressRateLimitPortControlMode OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
ingressRateLimitPerPortOnly(2),
ingressRateLimitPerQueue(3),
ingressRateLimitPerPortOnlyBpsMode(4),
ingressRateLimitPerQueueBpsMode(5),
ingressRateLimitPerPortOnlyKbpsMode(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The mode by which this port will be Rate-Limited on
ingress. If ingressRateLimitPerPortOnly is configured,
there will be a single maximum percentage-based rate for
the entire port. If ingressRateLimitPerQueue is
configured, the values for each of the queues indicate the
maximum percentage of port traffic that may be transmitted
by that queue. If ingressRateLimitPerPortOnlyBpsMode is
configured, there will be a single maximum bits-per-second
rate for the entire port. If
ingressRateLimitPerPortOnlyKbpsMode is configured, there
will be a single maximum kilobits-per-second rate for the
entire port. If ingressRateLimitPerQueueBpsMode is
configured, the maximum transmission-rate values for each
of the queues will be expressed in bits-per-second (again,
the sum of these values must not exceed the maximum
Bytes-per-second capability of the network link). The
queues are defined under hpIngressRateLimitPortPrctTable.
When ingress rate-limiting is disabled, there are no
maximum controls on ingress for this port."
DEFVAL { disabled }
::= { hpIngressRateLimitPortConfigEntry 2 }
hpIngressRateLimitPortSingleControlPrct OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "When hpIngressRateLimitPortControlMode is configured
for ingressRateLimitPerPortOnly, this value is the maximum
percentage of traffic that may be transmitted by this
port on egress."
::= { hpIngressRateLimitPortConfigEntry 3 }
hpIngressRateLimitPortSingleControlBps OBJECT-TYPE
SYNTAX Unsigned32 (0..4200000000)
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION "When hpIngressRateLimitPortControlMode is configured for
ingressRateLimitPerPortOnlyBpsMode, this value is the
maximum bits-per-second of traffic that may be transmitted
by this port on ingress."
::= { hpIngressRateLimitPortConfigEntry 4}
hpIngressRateLimitPortSingleControlKbps OBJECT-TYPE
SYNTAX Integer32 (0..10000000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "When hpIngressRateLimitPortControlMode is configured for
ingressRateLimitPerPortOnlyKbpsMode, this value is the
maximum kilobits-per-second of traffic that may be
transmitted by this port on ingress."
::= { hpIngressRateLimitPortConfigEntry 5}
hpIngressRateLimitPortPrctTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpIngressRateLimitPortPrctEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "A table that contains information about the port ingress
Rate-Limiting percent configurations on this switch. The
number of entries in this table is determined by
hpIngressRateLimitPortNumQueues. The priority of the
queues is in ascending order, starting with queue one
being the lowest priority and queue
hpIngressRateLimitPortNumQueues being the highest
priority."
::= { hpRateLimitIngressPortConfig 3 }
hpIngressRateLimitPortPrctEntry OBJECT-TYPE
SYNTAX HpIngressRateLimitPortPrctEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The information associated with each port's ingress
Rate-Limiting percent configuration."
INDEX { hpIngressRateLimitPortIndex,
hpIngressRateLimitPortPrctQueue }
::= { hpIngressRateLimitPortPrctTable 1 }
HpIngressRateLimitPortPrctEntry ::=
SEQUENCE {
hpIngressRateLimitPortPrctQueue Integer32,
hpIngressRateLimitPortPrct Integer32
}
hpIngressRateLimitPortPrctQueue OBJECT-TYPE
SYNTAX Integer32 (1..9000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The queue associated with this entry. The priority
of the queues is in ascending order, starting with
queue one being the lowest and queue
hpIngressRateLimitgressPortNumQueues being the highest."
::= { hpIngressRateLimitPortPrctEntry 1 }
hpIngressRateLimitPortPrct OBJECT-TYPE
SYNTAX Integer32 (0..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The maximum percentage of traffic that may be
transmitted by this port's queue on ingress.
hpIngressRateLimitPortControlMode must be configured to
use ingressRateLimitPerQueue for this to take effect. A
value of 0-percent for any queue means that no traffic
will ever be transmitted on this port for that ingress
queue. The values for each queue must not exceed 100
percent."
::= { hpIngressRateLimitPortPrctEntry 2 }
hpIngressRateLimitPortBpsTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpIngressRateLimitPortBpsEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION "A table that contains information about the port ingress
Rate-Limiting bits-per-second configurations on this
switch. The number of entries in this table is determined
by hpIngressRateLimitPortNumQueues. The priority of the
queues is in ascending order, starting with queue one
being the lowest priority and queue
hpIngressRateLimitPortNumQueues being the highest
priority queue."
::= { hpRateLimitIngressPortConfig 4 }
hpIngressRateLimitPortBpsEntry OBJECT-TYPE
SYNTAX HpIngressRateLimitPortBpsEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION "The information associated with each port's egress
Rate-Limiting bits-per-second configuration."
INDEX { hpIngressRateLimitPortIndex,
hpIngressRateLimitPortBpsQueue }
::= { hpIngressRateLimitPortBpsTable 1 }
HpIngressRateLimitPortBpsEntry ::=
SEQUENCE {
hpIngressRateLimitPortBpsQueue Integer32,
hpIngressRateLimitPortBps Unsigned32
}
hpIngressRateLimitPortBpsQueue OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION "The queue associated with this entry. The priority of
the queues is in ascending order, starting with queue one
being the lowest and queue
hpIngressRateLimitgressPortNumQueues being the highest."
::= { hpIngressRateLimitPortBpsEntry 1 }
hpIngressRateLimitPortBps OBJECT-TYPE
SYNTAX Unsigned32 (0..4200000000)
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION "The maximum bits-per-second of traffic that may be
transmitted by this port's queue on ingress.
hpIngressRateLimitPortControlMode must be configured to
use ingressRateLimitPerQueue for this to take effect. A
value of 0-percent for any queue means that no traffic
will ever be transmitted on this port for that ingress
queue. The values for each queue must not exceed the
bits-per-second capability of the current network link
speed."
::= { hpIngressRateLimitPortBpsEntry 2 }
-- Conformance Information
hpicfRateLimitConformance OBJECT IDENTIFIER ::= { hpicfRateLimitMIB 2 }
hpicfRateLimitGroups OBJECT IDENTIFIER ::= { hpicfRateLimitConformance 1 }
hpicfRateLimitCompliances OBJECT IDENTIFIER
::= { hpicfRateLimitConformance 2 }
-- units of conformance
hpICMPRateLimitPortConfigGroup OBJECT-GROUP
OBJECTS {
hpICMPRateLimitPortState,
hpICMPRateLimitPortPrct,
hpICMPRateLimitPortAlarmFlag,
hpICMPRateLimitNotifyPortIndex
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing configuration to ICMP rate
limiting on an interface."
::= { hpicfRateLimitGroups 1 }
hpICMPRateLimitPortNotifyGroup NOTIFICATION-GROUP
NOTIFICATIONS { hpICMPRateLimitPortNotification }
STATUS current
DESCRIPTION "A collection of notifications used to indicate
ICMP rate limiting on an interface events."
::= { hpicfRateLimitGroups 2 }
hpBWMinIngressPortConfigGroup OBJECT-GROUP
OBJECTS { hpBWMinIngressPortNumQueues,
hpBWMinIngressPortPrct }
STATUS current
DESCRIPTION
"A collection of objects providing configuration to Guaranteed
Minimum ingress bandwidth on an interface."
::= { hpicfRateLimitGroups 3 }
hpBWMinEgressPortConfigGroup OBJECT-GROUP
OBJECTS { hpBWMinEgressPortNumQueues,
hpBWMinEgressPortPrct }
STATUS current
DESCRIPTION
"A collection of objects providing configuration to Guaranteed
Minimum egress bandwidth on an interface."
::= { hpicfRateLimitGroups 4 }
hpEgressRateLimitPortConfigGroup OBJECT-GROUP
OBJECTS { hpEgressRateLimitPortNumQueues,
hpEgressRateLimitPortControlMode,
hpEgressRateLimitPortSingleControlPrct,
hpEgressRateLimitPortSingleControlBps,
hpEgressRateLimitPortPrct,
hpEgressRateLimitPortBps,
hpEgressRateLimitPortSingleControlKbps
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing configuration to Egress
Rate-Limiting on an interface."
::= { hpicfRateLimitGroups 5 }
hpIngressRateLimitPortConfigGroup OBJECT-GROUP
OBJECTS { hpIngressRateLimitPortNumQueues,
hpIngressRateLimitPortControlMode,
hpIngressRateLimitPortSingleControlPrct,
hpIngressRateLimitPortSingleControlBps,
hpIngressRateLimitPortPrct,
hpIngressRateLimitPortBps,
hpIngressRateLimitPortSingleControlKbps
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing configuration to Ingress
Rate-Limiting on an interface."
::= { hpicfRateLimitGroups 6 }
hpICMPRateLimitPortConfigGroup2 OBJECT-GROUP
OBJECTS {
hpICMPRateLimitPortPrct,
hpICMPRateLimitPortAlarmFlag,
hpICMPRateLimitNotifyPortIndex,
hpICMPRateLimitPortKbps,
hpICMPRateLimitPortControlMode
}
STATUS current
DESCRIPTION
"This replaces the deprecated hpICMPRateLimitPortConfigGroup.
A collection of objects providing configuration to ICMP rate
limiting on an interface."
::= { hpicfRateLimitGroups 7 }
hpEgressRateLimitPortConfigGroup2 OBJECT-GROUP
OBJECTS { hpEgressRateLimitPortNumQueues,
hpEgressRateLimitPortControlMode,
hpEgressRateLimitPortSingleControlPrct,
hpEgressRateLimitPortPrct,
hpEgressRateLimitPortSingleControlKbps
}
STATUS current
DESCRIPTION
"This replaces the deprecated hpEgressRateLimitPortConfigGroup.
A collection of objects providing configuration to Egress
Rate-Limiting on an interface."
::= { hpicfRateLimitGroups 8 }
hpIngressRateLimitPortConfigGroup2 OBJECT-GROUP
OBJECTS { hpIngressRateLimitPortNumQueues,
hpIngressRateLimitPortControlMode,
hpIngressRateLimitPortSingleControlPrct,
hpIngressRateLimitPortPrct,
hpIngressRateLimitPortSingleControlKbps
}
STATUS current
DESCRIPTION
"This replaces the deprecated hpIngressRateLimitPortConfigGroup.
A collection of objects providing configuration to Ingress
Rate-Limiting on an interface."
::= { hpicfRateLimitGroups 9 }
-- compliance statements
hpicfRateLimitCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for devices support of
HP-ICF-RATE-LIMIT MIB."
MODULE -- This Module
MANDATORY-GROUPS { hpICMPRateLimitPortConfigGroup,
hpICMPRateLimitPortNotifyGroup
}
::= { hpicfRateLimitCompliances 1 }
hpicfRateLimitCompliance1 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for devices support of
HP-ICF-RATE-LIMIT MIB."
MODULE -- This Module
MANDATORY-GROUPS { hpICMPRateLimitPortConfigGroup2,
hpICMPRateLimitPortNotifyGroup,
hpBWMinIngressPortConfigGroup,
hpEgressRateLimitPortConfigGroup2,
hpIngressRateLimitPortConfigGroup2
}
::= { hpicfRateLimitCompliances 2 }
END