mibs/hp/HP-ICF-UDLD-MIB
HP-ICF-UDLD-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, Integer32,
Counter32, Unsigned32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
MacAddress, TimeInterval
FROM SNMPv2-TC
ifIndex
FROM IF-MIB
hpSwitch
FROM HP-ICF-OID;
hpicfUdldMIB MODULE-IDENTITY
LAST-UPDATED "200604100000Z" --April 10, 2006
ORGANIZATION "Hewlett-Packard Company
ProCurve Networking Business"
CONTACT-INFO "Hewlett-Packard Company
8000 Foothills Blvd.
Roseville, CA 95747"
DESCRIPTION "This MIB module describes objects to configure
the Unidirectional Link Detection (UDLD) feature."
REVISION "200604100000Z"
DESCRIPTION "Initial revision."
::= { hpSwitch 33 }
-- **********************************************************************
-- The UDLD MIB Groups
-- **********************************************************************
hpicfUdldNotifications OBJECT IDENTIFIER ::= { hpicfUdldMIB 0 }
hpicfUdldObjects OBJECT IDENTIFIER ::= { hpicfUdldMIB 1 }
hpicfUdldConformance OBJECT IDENTIFIER ::= { hpicfUdldMIB 2 }
-- **********************************************************************
-- The UDLD MIB Objects
-- **********************************************************************
hpicfUdldConfig OBJECT IDENTIFIER ::= { hpicfUdldObjects 1 }
hpicfUdldStats OBJECT IDENTIFIER ::= { hpicfUdldObjects 2 }
-- **********************************************************************
-- Start of MIB objects
-- **********************************************************************
hpicfUdldConfigTimeInterval OBJECT-TYPE
SYNTAX Unsigned32 (10..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The interval in seconds at which the UDLD enabled ports exchange
proprietary pulse packet. Here 10 is 1 sec, 11 is 1.1 sec,
and so on. The default value for hpicfUdldConfigTimeInterval
object is 5 seconds."
DEFVAL { 50 } -- five second
::= { hpicfUdldConfig 1 }
hpicfUdldConfigMaxRetries OBJECT-TYPE
SYNTAX Unsigned32 (3..10)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Maximum number of retries to wait for a response.
The default value for hpicfUdldConfigMaxRetries object is
4."
DEFVAL { 4 }
::= { hpicfUdldConfig 2 }
-- Start of hpicfUdldPortConfigTable ************************************
hpicfUdldPortConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpicfUdldPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The table that controls UDLD status on individual ports."
::= { hpicfUdldConfig 3 }
hpicfUdldPortConfigEntry OBJECT-TYPE
SYNTAX HpicfUdldPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the hpicfUdldPortConfigTable."
INDEX { ifIndex }
::= { hpicfUdldPortConfigTable 1 }
HpicfUdldPortConfigEntry ::= SEQUENCE {
hpicfUdldPortAdminStatus INTEGER,
hpicfUdldPortVlanId Integer32
}
hpicfUdldPortAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The hpicfUdldPortAdminStatus can be enabled/disabled
The value enable(1) means that UDLD is enabled.
the value disable(2) means that UDLD is disabled."
::= { hpicfUdldPortConfigEntry 1 }
hpicfUdldPortVlanId OBJECT-TYPE
SYNTAX Integer32 (0..4094)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The vlan id associated with tagged UDLD control
packets. The value of 0 indicates that UDLD control
packets are untagged."
::= { hpicfUdldPortConfigEntry 2 }
-- End of hpicfUdldPortConfigTable **************************************
--
-- ***********************************************************
--
-- UDLD S T A T S
--
-- ***********************************************************
--
hpicfUdldPortStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF HpicfUdldPortStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing UDLD statistics for
individual ports."
::= { hpicfUdldStats 1 }
hpicfUdldPortStatsEntry OBJECT-TYPE
SYNTAX HpicfUdldPortStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"UDLD statistics for a particular physical port."
INDEX { ifIndex }
::= { hpicfUdldPortStatsTable 1 }
HpicfUdldPortStatsEntry ::= SEQUENCE {
hpicfUdldStatsPortCurrentState INTEGER,
hpicfUdldStatsPortNeighborMAC MacAddress,
hpicfUdldStatsPortNeighborPort Integer32,
hpicfUdldStatsPortTotalTx Counter32,
hpicfUdldStatsPortTotalRx Counter32,
hpicfUdldStatsPortNumStateChange Counter32,
hpicfUdldStatsPortStatus Integer32
}
hpicfUdldStatsPortCurrentState OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
offline(1),
failure(2),
up(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The desired status of UDLD on a port.
If the associated hpicfUdldStatsPortCurrentState object has a
value of 'offline(1)', then the port or udld is administratively
disabled.
If the associated hpicfUdldStatsPortCurrentState object has a
value of 'failure(2)', then the port and udld are administratively
enabled, but udld packets are not being received successfully.
Link may or may not be present.
If the associated hpicfUdldStatsPortCurrentState object has a
value of 'up(3)', then udld is enabled and udld packets
are being received successfully in both directions."
::= { hpicfUdldPortStatsEntry 1 }
hpicfUdldStatsPortNeighborMAC OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The MAC address of the adjacent switch."
::= { hpicfUdldPortStatsEntry 2 }
hpicfUdldStatsPortNeighborPort OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The port number of the adjacent switch."
::= { hpicfUdldPortStatsEntry 3 }
hpicfUdldStatsPortTotalTx OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of UDLD control packets sent from this port."
::= { hpicfUdldPortStatsEntry 4 }
hpicfUdldStatsPortTotalRx OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of UDLD control packets received on this port."
::= { hpicfUdldPortStatsEntry 5 }
hpicfUdldStatsPortNumStateChange OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of state transitions."
::= { hpicfUdldPortStatsEntry 6 }
hpicfUdldStatsPortStatus OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object indicates whether the port is
blocked by UDLD or not."
::= { hpicfUdldPortStatsEntry 7 }
--
-- ***********************************************************
--
-- UDLD M I B N O T I F I C A T I O N S
--
-- ***********************************************************
--
hpicfUdldNotificationPrefix OBJECT IDENTIFIER ::= { hpicfUdldNotifications 0 }
hpicfUdldLinkfault NOTIFICATION-TYPE
OBJECTS { ifIndex }
STATUS current
DESCRIPTION "This notification is generated when the link failure
occurs."
::= { hpicfUdldNotificationPrefix 1 }
hpicfUdldLinkUp NOTIFICATION-TYPE
OBJECTS { ifIndex }
STATUS current
DESCRIPTION "This notification is generated when UDLD link goes
from down to up."
::= { hpicfUdldNotificationPrefix 2 }
--
-- ***********************************************************
--
-- UDLD M I B C O N F O R M A N C E
--
-- ***********************************************************
--
hpicfUdldCompliances OBJECT IDENTIFIER ::= { hpicfUdldConformance 1 }
hpicfUdldGroups OBJECT IDENTIFIER ::= { hpicfUdldConformance 2 }
-- compliance statements
hpicfUdldCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which implement
the UDLD MIB."
MODULE -- this module
MANDATORY-GROUPS {
hpicfUdldPortConfigGroup,
hpicfUdldPortStatsGroup,
hpicfUdldNotificationGroup
}
GROUP hpicfUdldNotificationGroup
DESCRIPTION "The notifications used for signalling link failure."
::= { hpicfUdldCompliances 1 }
-- MIB groupings
hpicfUdldPortConfigGroup OBJECT-GROUP
OBJECTS {
hpicfUdldConfigTimeInterval,
hpicfUdldConfigMaxRetries,
hpicfUdldPortAdminStatus,
hpicfUdldPortVlanId
}
STATUS current
DESCRIPTION
"The collection of objects which are used to configure the
UDLD implementation behavior.
This group is mandatory for ports which implement the UDLD."
::= { hpicfUdldGroups 1 }
hpicfUdldPortStatsGroup OBJECT-GROUP
OBJECTS {
hpicfUdldStatsPortCurrentState,
hpicfUdldStatsPortNeighborMAC,
hpicfUdldStatsPortNeighborPort,
hpicfUdldStatsPortTotalTx,
hpicfUdldStatsPortTotalRx,
hpicfUdldStatsPortNumStateChange,
hpicfUdldStatsPortStatus
}
STATUS current
DESCRIPTION
"The collection of objects which are used to represent UDLD
statistics.
This group is mandatory for ports which implement the UDLD."
::= { hpicfUdldGroups 2 }
hpicfUdldNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS { hpicfUdldLinkfault,hpicfUdldLinkUp }
STATUS current
DESCRIPTION "Notification used for signaling change in Link state."
::= { hpicfUdldGroups 3 }
END