mibs/hp/HP-SN-MPLS-LSR-MIB
HP-SN-MPLS-LSR-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Integer32, Counter32, Unsigned32, Counter64, Gauge32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
TruthValue, RowStatus, StorageType, RowPointer,
TimeStamp
FROM SNMPv2-TC
InterfaceIndex, InterfaceIndexOrZero
FROM IF-MIB
mplsMIB, MplsLSPID, MplsLabel, MplsBitRate, MplsBurstSize,
MplsInitialCreationSource
FROM HP-SN-MPLS-TC-MIB
AddressFamilyNumbers
FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB
InetAddressIPv4, InetAddressIPv6, InetAddressType
FROM INET-ADDRESS-MIB
snMpls
FROM HP-SN-ROOT-MIB;
mplsLsrMIB MODULE-IDENTITY
LAST-UPDATED "200201041200Z" -- 4 January 2002 12:00:00 GMT
ORGANIZATION "Multiprotocol Label Switching (MPLS) Working Group"
CONTACT-INFO
"
Cheenu Srinivasan
Postal: Parama Networks, Inc.
1030 Broad Street
Shrewsbury, NJ 07702
Tel: +1-732-544-9120 x731
Email: cheenu@paramanet.com
Arun Viswanathan
Postal: Force10 Networks, Inc.
1440 McCarthy Blvd
Milpitas, CA 95035
Tel: +1-408-571-3516
Email: arun@force10networks.com
Thomas D. Nadeau
Postal: Cisco Systems, Inc.
250 Apollo Drive
Chelmsford, MA 01824
Tel: +1-978-244-3051
Email: tnadeau@cisco.com
"
DESCRIPTION
"This MIB contains managed object definitions for the
Multiprotocol Label Switching (MPLS) Router as
defined in: Rosen, E., Viswanathan, A., and R.
Callon, Multiprotocol Label Switching Architecture,
RFC 3031, January 2001."
-- Revision history.
REVISION
"200201041200Z" -- 4 January 2002 12:00:00 GMT
DESCRIPTION
"Initial revision, published as part of RFC XXXX."
::= { mplsMIB 2 }
-- Top level components of this MIB.
-- Tables, Scalars
mplsLsrObjects OBJECT IDENTIFIER ::= { mplsLsrMIB 1 }
-- Notifications
mplsLsrNotifications OBJECT IDENTIFIER ::= { mplsLsrMIB 2 }
mplsLsrNotifyPrefix OBJECT IDENTIFIER ::= { mplsLsrNotifications 0 }
-- conformance
mplsLsrConformance OBJECT IDENTIFIER ::= { mplsLsrMIB 3 }
-- MPLS Interface Configuration Table.
mplsInterfaceConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsInterfaceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies per-interface MPLS capability
and associated information."
::= { mplsLsrObjects 1 }
mplsInterfaceConfEntry OBJECT-TYPE
SYNTAX MplsInterfaceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by an LSR for
every interface capable of supporting MPLS. Each
entry in this table will exist only if a
corresponding entry in ifTable exists. If the
associated entry in ifTable is deleted, the
corresponding entry in this table must also be
deleted shortly thereafter. The entry with index 0
represents the per-platform label space and contains
parameters that apply to all interfaces that
participate in the per-platform label space. Other
entries defined in this table represent additional
MPLS interfaces that may participate in either the
per-platform or per-interface label spaces, or both.
Additional information about label space
participation of an interface is provided in the
description clause of
mplsInterfaceLabelParticipationType."
INDEX { mplsInterfaceConfIndex }
::= { mplsInterfaceConfTable 1 }
MplsInterfaceConfEntry ::= SEQUENCE {
mplsInterfaceConfIndex InterfaceIndexOrZero,
mplsInterfaceLabelMinIn MplsLabel,
mplsInterfaceLabelMaxIn MplsLabel,
mplsInterfaceLabelMinOut MplsLabel,
mplsInterfaceLabelMaxOut MplsLabel,
mplsInterfaceTotalBandwidth MplsBitRate,
mplsInterfaceAvailableBandwidth MplsBitRate,
mplsInterfaceLabelParticipationType BITS
}
mplsInterfaceConfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This is a unique index for an entry in the
MplsInterfaceConfTable. A non-zero index for an
entry indicates the ifIndex for the corresponding
interface entry in of the MPLS-layer in the ifTable.
Note that the per-platform label space may apply to
several interfaces, and therefore the configuration
of the per-platform label space interface parameters
will apply to all of the interfaces that are
participating in the per-platform label space."
REFERENCE
"RFC 2863 - The Interfaces Group MIB, McCloghrie, K.,
and F. Kastenholtz, June 2000"
::= { mplsInterfaceConfEntry 1 }
mplsInterfaceLabelMinIn OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the minimum value of an MPLS label that this
LSR is willing to receive on this interface."
::= { mplsInterfaceConfEntry 2 }
mplsInterfaceLabelMaxIn OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the maximum value of an MPLS label that this
LSR is willing to receive on this interface."
::= { mplsInterfaceConfEntry 3 }
mplsInterfaceLabelMinOut OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the minimum value of an MPLS label that this
LSR is willing to send on this interface."
::= { mplsInterfaceConfEntry 4 }
mplsInterfaceLabelMaxOut OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the maximum value of an MPLS label that this
LSR is willing to send on this interface."
::= { mplsInterfaceConfEntry 5 }
mplsInterfaceTotalBandwidth OBJECT-TYPE
SYNTAX MplsBitRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value indicates the total amount of usable
bandwidth on this interface and is specified in
kilobits per second (Kbps). This variable is not
applicable when applied to the interface with index
0. When this value cannot be measured, this value
should contain the nominal bandwidth."
::= { mplsInterfaceConfEntry 6 }
mplsInterfaceAvailableBandwidth OBJECT-TYPE
SYNTAX MplsBitRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value indicates the total amount of available
bandwidth available on this interface and is
specified in kilobits per second (Kbps). This value
is calculated as the difference between the amount
of bandwidth currently in use and that specified in
mplsInterfaceTotalBandwidth. This variable is not
applicable when applied to the interface with index
0. When this value cannot be measured, this value
should contain the nominal bandwidth."
::= { mplsInterfaceConfEntry 7 }
mplsInterfaceLabelParticipationType OBJECT-TYPE
SYNTAX BITS {
perPlatform (0),
perInterface (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Either the perPlatform(0) or perInterface(1) bit
MUST be set. If the value of the
mplsInterfaceConfIndex for this entry is zero, then
only the perPlatform(0) bit MUST be set and the
perInterface(1) bit is meaningless. If the
perInterface(1) bit is set then the value of
mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn,
mplsInterfaceLabelMinOut, and
mplsInterfaceLabelMaxOut for this entry reflect the
label ranges for this interface. If only the
perPlatform(0) bit is set, then the value of
mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn,
mplsInterfaceLabelMinOut, and
mplsInterfaceLabelMaxOut for this entry must be
identical to the instance of these objects with
index 0."
REFERENCE
"Rosen, E., Viswanathan, A., and R. Callon,
Multiprotocol Label Switching Architecture, RFC
3031, January 2001."
::= { mplsInterfaceConfEntry 8 }
-- End of mplsInterfaceConfTable
-- MPLS Interface Performance Table.
mplsInterfacePerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsInterfacePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides MPLS performance information on
a per-interface basis."
::= { mplsLsrObjects 2 }
mplsInterfacePerfEntry OBJECT-TYPE
SYNTAX MplsInterfacePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the LSR for
every interface capable of supporting MPLS. Its is
an extension to the mplsInterfaceConfEntry table."
AUGMENTS { mplsInterfaceConfEntry }
::= { mplsInterfacePerfTable 1 }
MplsInterfacePerfEntry ::= SEQUENCE {
-- incoming direction
mplsInterfaceInLabelsUsed Gauge32,
mplsInterfaceFailedLabelLookup Counter32,
-- outgoing direction
mplsInterfaceOutLabelsUsed Gauge32,
mplsInterfaceOutFragments Counter32
}
mplsInterfaceInLabelsUsed OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of labels that are in
use at this point in time on this interface in the
incoming direction. If the interface participates in
the per-platform label space only, then this
instance of this object MUST be identical with the
instance with index 0. If the interface participates
in the per-interface label space, then this instance
of this object MUST represent the number of of per-
interface labels that are in use at this point in
time on this interface."
::= { mplsInterfacePerfEntry 1 }
mplsInterfaceFailedLabelLookup OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of labeled packets
that have been received on this interface and were
discarded because there was no matching cross-
connect entry. This object MUST count on a per-
interface basis regardless of which label space the
interface participates in."
::= { mplsInterfacePerfEntry 2 }
mplsInterfaceOutLabelsUsed OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of top-most labels in
the outgoing label stacks that are in use at this
point in time on this interface. This object MUST
count on a per-interface basis regardless of which
label space the interface participates in."
::= { mplsInterfacePerfEntry 3 }
mplsInterfaceOutFragments OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of outgoing MPLS
packets that required fragmentation before
transmission on this interface. This object MUST
count on a per-interface basis regardless of which
label space the interface participates in."
::= { mplsInterfacePerfEntry 4 }
-- In-segment table.
mplsInSegmentTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsInSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains a collection of incoming
segments to an LSR."
::= { mplsLsrObjects 3 }
mplsInSegmentEntry OBJECT-TYPE
SYNTAX MplsInSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents one incoming
segment. An entry can be created by a network
administrator or an SNMP agent, or an MPLS signaling
protocol. The creator of the entry is denoted by
mplsInSegmentOwner. An entry in this table is
indexed by the ifIndex of the incoming interface and
the (top) label. The value of mplsInSegmentRowStatus
cannot be active(1)unless the ifTable entry
corresponding to mplsInSegmentIfIndex exists."
INDEX { mplsInSegmentIfIndex, mplsInSegmentLabel }
::= { mplsInSegmentTable 1 }
MplsInSegmentEntry ::= SEQUENCE {
mplsInSegmentIfIndex InterfaceIndexOrZero,
mplsInSegmentLabel MplsLabel,
mplsInSegmentNPop Integer32,
mplsInSegmentAddrFamily AddressFamilyNumbers,
mplsInSegmentXCIndex Unsigned32,
mplsInSegmentOwner MplsInitialCreationSource ,
mplsInSegmentTrafficParamPtr RowPointer,
mplsInSegmentRowStatus RowStatus,
mplsInSegmentStorageType StorageType
}
mplsInSegmentIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This is a unique index for an entry in the
MplsInSegmentTable. This value represents the
interface index for the incoming MPLS interface. A
value of zero represents an incoming label from the
per-platform label space. In this case, the
mplsInSegmentLabel is interpreted to be an MPLS-type
label."
::= { mplsInSegmentEntry 1 }
mplsInSegmentLabel OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The incoming label for this segment."
::= { mplsInSegmentEntry 2 }
mplsInSegmentNPop OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of labels to pop from the incoming
packet. Normally only the top label is popped from
the packet and used for all switching decisions for
that packet. Note that technologies which do not
support label popping should set this value to its
default value of 1. This object cannot be modified
if mplsInSegmentRowStatus is active(1)."
DEFVAL { 1 }
::= { mplsInSegmentEntry 3 }
mplsInSegmentAddrFamily OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The IANA address family [IANAFamily] of the incoming
packet. A value of other(0) indicates that the
family type is either unknown or undefined. This
object cannot be modified if mplsInSegmentRowStatus
is active(1)."
DEFVAL { other }
::= { mplsInSegmentEntry 4 }
mplsInSegmentXCIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index into mplsXCTable which identifies which cross-
connect entry this segment is part of. A value of
zero indicates that this entry is not referred to by
any cross-connect entry. When a cross-connect entry
is created which this in-segment is a part of, this
object is automatically updated to reflect the value
of mplsXCIndex of that cross-connect entry."
DEFVAL { 0 }
::= { mplsInSegmentEntry 5 }
mplsInSegmentOwner OBJECT-TYPE
SYNTAX MplsInitialCreationSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes the entity that created and is responsible
for managing this segment. This object cannot be
modified if mplsInSegmentRowStatus is active(1)."
DEFVAL { unknown }
::= { mplsInSegmentEntry 6 }
mplsInSegmentTrafficParamPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable represents a pointer to the traffic
parameter specification for this in-segment. This
value may point at an entry in the
mplsTrafficParamTable to indicate which
mplsTrafficParamEntry is to be assigned to this
segment. This value may optionally point at an
externally defined traffic parameter specification
table. A value of zero-dot-zero indicates best-effort
treatment. By having the same value of this object,
two or more segments can indicate resource sharing.
This object cannot be modified if
mplsInSegmentRowStatus is active(1)."
::= { mplsInSegmentEntry 7 }
mplsInSegmentRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable is used to create, modify, and/or
delete a row in this table."
::= { mplsInSegmentEntry 8 }
mplsInSegmentStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object. This object cannot be modified if
mplsInSegmentRowStatus is active(1). If this
variable is set to readOnly(5), and the
corresponding TFIB entry is removed, then the agent
must remove this row shortly thereafter."
::= { mplsInSegmentEntry 9 }
-- End of mplsInSegmentTable
-- In-segment performance table.
mplsInSegmentPerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsInSegmentPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains statistical information for
incoming MPLS segments to an LSR."
::= { mplsLsrObjects 4 }
mplsInSegmentPerfEntry OBJECT-TYPE
SYNTAX MplsInSegmentPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table contains statistical
information about one incoming segment which was
configured in the mplsInSegmentTable. The counters
in this entry should behave in a manner similar to
that of the interface."
AUGMENTS { mplsInSegmentEntry }
::= { mplsInSegmentPerfTable 1 }
MplsInSegmentPerfEntry ::= SEQUENCE {
mplsInSegmentOctets Counter32,
mplsInSegmentPackets Counter32,
mplsInSegmentErrors Counter32,
mplsInSegmentDiscards Counter32,
-- high capacity counter
mplsInSegmentHCOctets Counter64,
mplsInSegmentPerfDiscontinuityTime TimeStamp
}
mplsInSegmentOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value represents the total number of octets
received by this segment."
::= { mplsInSegmentPerfEntry 1 }
mplsInSegmentPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of packets received by this segment."
::= { mplsInSegmentPerfEntry 2 }
mplsInSegmentErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of errored packets received on this
segment."
::= { mplsInSegmentPerfEntry 3 }
mplsInSegmentDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of labeled packets received on this in-
segment, which were chosen to be discarded even
though no errors had been detected to prevent their
being transmitted. One possible reason for
discarding such a labeled packet could be to free up
buffer space."
::= { mplsInSegmentPerfEntry 4 }
mplsInSegmentHCOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received. This is the 64
bit version of mplsInSegmentOctets."
::= { mplsInSegmentPerfEntry 5 }
mplsInSegmentPerfDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
at which any one or more of this segment's Counter32
or Counter64 suffered a discontinuity. If no such
discontinuities have occurred since the last re-
initialization of the local management subsystem,
then this object contains a zero value."
::= { mplsInSegmentPerfEntry 6 }
-- End of mplsInSegmentPerfTable.
-- Out-segment table.
mplsOutSegmentIndexNext OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the next appropriate value to
be used for mplsOutSegmentIndex when creating
entries in the mplsOutSegmentTable. If the number
of unassigned entries is exhausted, this object will
take on the value of 0. To obtain the
mplsOutSegmentIndex value for a new entry, the
manager must first issue a management protocol
retrieval operation to obtain the current value of
this object. The agent should modify the value to
reflect the next unassigned index after each
retrieval operation. After a manager retrieves a
value the agent will determine through its local
policy when this index value will be made available
for reuse."
::= { mplsLsrObjects 5 }
mplsOutSegmentTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsOutSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains a representation of the outgoing
segments from an LSR."
::= { mplsLsrObjects 6 }
mplsOutSegmentEntry OBJECT-TYPE
SYNTAX MplsOutSegmentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents one outgoing
segment. An entry can be created by a network
administrator or an SNMP agent, or an MPLS signaling
protocol. The object mplsOutSegmentOwner indicates
the creator of this entry. The value of
mplsOutSegmentRowStatus cannot be active(1)unless
the ifTable entry corresponding to
mplsOutSegmentIfIndex exists."
INDEX { mplsOutSegmentIndex }
::= { mplsOutSegmentTable 1 }
MplsOutSegmentEntry ::= SEQUENCE {
mplsOutSegmentIndex Unsigned32,
mplsOutSegmentIfIndex InterfaceIndexOrZero,
mplsOutSegmentPushTopLabel TruthValue,
mplsOutSegmentTopLabel MplsLabel,
mplsOutSegmentNextHopIpAddrType InetAddressType,
mplsOutSegmentNextHopIpv4Addr InetAddressIPv4,
mplsOutSegmentNextHopIpv6Addr InetAddressIPv6,
mplsOutSegmentXCIndex Unsigned32,
mplsOutSegmentOwner MplsInitialCreationSource ,
mplsOutSegmentTrafficParamPtr RowPointer,
mplsOutSegmentRowStatus RowStatus,
mplsOutSegmentStorageType StorageType
}
mplsOutSegmentIndex OBJECT-TYPE
SYNTAX Unsigned32(0..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value contains a unique index for this row.
While a value of 0 is not valid as an index for this
row it can be supplied as a valid value to index
mplsXCTable to access entries for which no out-
segment has been configured."
::= { mplsOutSegmentEntry 1 }
mplsOutSegmentIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value must contain the interface index of the
outgoing interface. This object may only take the
value of 0 during the create-and-wait row creation
operation if the management station has not yet set
the value of this object. This object cannot be
modified if mplsOutSegmentRowStatus is active(1).
The mplsOutSegmentRowStatus cannot be set to
active(1) until this object is set to a value
corresponding to a valid ifEntry."
DEFVAL { 0 }
::= { mplsOutSegmentEntry 2 }
mplsOutSegmentPushTopLabel OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value indicates whether or not a top label
should be pushed onto the outgoing packet's label
stack. The value of this variable MUST be set to
true if the outgoing interface does not support pop-
and-go (for example an ATM interface) or if it is a
tunnel origination. Note that it is considered an
error in the case that mplsOutSegmentPushTopLabel is
set to false, but the cross-connect entry which
refers to this out-segment has a non-zero
mplsLabelStackIndex. The LSR MUST ensure that this
situation does not happen. This object cannot be
modified if mplsOutSegmentRowStatus is active(1)."
::= { mplsOutSegmentEntry 3 }
mplsOutSegmentTopLabel OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If mplsOutSegmentPushTopLabel is true then this
represents the label that should be pushed onto the
top of the outgoing packet's label stack. Otherwise
this value SHOULD be set to 0 by the management
station and MUST be ignored by the agent. This
object cannot be modified if mplsOutSegmentRowStatus
is active(1)."
DEFVAL { 0 }
::= { mplsOutSegmentEntry 4 }
mplsOutSegmentNextHopIpAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the next hop address is IPv4 or
IPv6. Note that a value of unknown (0) is valid
only when the outgoing interface is of type point-to-
point. This object cannot be modified if
mplsOutSegmentRowStatus is active(1)."
DEFVAL { unknown }
::= { mplsOutSegmentEntry 5 }
mplsOutSegmentNextHopIpv4Addr OBJECT-TYPE
SYNTAX InetAddressIPv4
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"IPv4 Address of the next hop. Its value is
significant only when
mplsOutSegmentNextHopIpAddrType is ipV4 (1),
otherwise it SHOULD return a value of 0. This object
cannot be modified if mplsOutSegmentRowStatus is
active(1)."
::= { mplsOutSegmentEntry 6 }
mplsOutSegmentNextHopIpv6Addr OBJECT-TYPE
SYNTAX InetAddressIPv6
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"IPv6 address of the next hop. Its value is
significant only when
mplsOutSegmentNextHopIpAddrType is ipV6 (2),
otherwise it SHOULD return a value of 0. This object
cannot be modified if mplsOutSegmentRowStatus is
active(1)."
::= { mplsOutSegmentEntry 7 }
mplsOutSegmentXCIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index into mplsXCTable which identifies which cross-
connect entry this segment is part of. A value of
zero indicates that this entry is not referred to by
any cross-connect entry. When a cross-connect entry
is created which this out-segment is a part of, this
object is automatically updated to reflect the value
of mplsXCIndex of that cross-connect entry."
DEFVAL { 0 }
::= { mplsOutSegmentEntry 8 }
mplsOutSegmentOwner OBJECT-TYPE
SYNTAX MplsInitialCreationSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes the entity which created and is responsible
for managing this segment. This object cannot be
modified if mplsOutSegmentRowStatus is active(1)."
DEFVAL { unknown }
::= { mplsOutSegmentEntry 9 }
mplsOutSegmentTrafficParamPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable represents a pointer to the traffic
parameter specification for this out-segment. This
value may point at an entry in the
mplsTrafficParamTable to indicate which
mplsTrafficParamEntry is to be assigned to this
segment. This value may optionally point at an
externally defined traffic parameter specification
table. A value of zero-dot-zero indicates best-
effort treatment. By having the same value of this
object, two or more segments can indicate resource
sharing. This object cannot be modified if
mplsOutSegmentRowStatus is active(1)."
::= { mplsOutSegmentEntry 10 }
mplsOutSegmentRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row."
::= { mplsOutSegmentEntry 11 }
mplsOutSegmentStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
object. This object cannot be modified if
mplsOutSegmentRowStatus is active(1). If this
variable is set to readOnly(5), and the
corresponding TFIB entry is removed, then the agent
must remove this row shortly thereafter."
::= { mplsOutSegmentEntry 12 }
-- End of mplsOutSegmentTable
-- Out-segment performance table.
mplsOutSegmentPerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsOutSegmentPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains statistical information about
outgoing segments from an LSR. The counters in this
entry should behave in a manner similar to that of
the interface."
::= { mplsLsrObjects 7 }
mplsOutSegmentPerfEntry OBJECT-TYPE
SYNTAX MplsOutSegmentPerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table contains statistical
information about one outgoing segment configured in
mplsOutSegmentTable."
AUGMENTS { mplsOutSegmentEntry }
::= { mplsOutSegmentPerfTable 1 }
MplsOutSegmentPerfEntry ::= SEQUENCE {
mplsOutSegmentOctets Counter32,
mplsOutSegmentPackets Counter32,
mplsOutSegmentErrors Counter32,
mplsOutSegmentDiscards Counter32,
-- HC counter
mplsOutSegmentHCOctets Counter64,
mplsOutSegmentPerfDiscontinuityTime TimeStamp
}
mplsOutSegmentOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value contains the total number of octets sent
on this segment."
::= { mplsOutSegmentPerfEntry 1 }
mplsOutSegmentPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value contains the total number of packets sent
on this segment."
::= { mplsOutSegmentPerfEntry 2 }
mplsOutSegmentErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets that could not be sent due to
errors on this segment."
::= { mplsOutSegmentPerfEntry 3 }
mplsOutSegmentDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of labeled packets received on this out-
segment, which were chosen to be discarded even
though no errors had been detected to prevent their
being transmitted. One possible reason for
discarding such a labeled packet could be to free up
buffer space."
::= { mplsOutSegmentPerfEntry 4 }
mplsOutSegmentHCOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of octets sent. This is the 64 bit
version of mplsOutSegmentOctets."
::= { mplsOutSegmentPerfEntry 5 }
mplsOutSegmentPerfDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
at which any one or more of this segment's Counter32
or Counter64 suffered a discontinuity. If no such
discontinuities have occurred since the last re-
initialization of the local management subsystem,
then this object contains a zero value."
::= { mplsOutSegmentPerfEntry 6 }
-- End of mplsOutSegmentPerfTable.
-- Cross-connect table.
mplsXCIndexNext OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to be used
for mplsXCIndex when creating entries in the
mplsXCTable. The value 0 indicates that no
unassigned entries are available. To obtain the
value of mplsXCIndex for a new entry in the
mplsXCTable, the manager issues a management
protocol retrieval operation to obtain the current
value of mplsXCIndex. After each retrieval
operation, the agent should modify the value to
reflect the next unassigned index. After a manager
retrieves a value the agent will determine through
its local policy when this index value will be made
available for reuse."
::= { mplsLsrObjects 8 }
mplsXCTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsXCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies information for switching
between LSP segments. It supports point-to-point,
point-to-multipoint and multipoint-to-point
connections. mplsLabelStackTable specifies the
label stack information for a cross-connect LSR and
is referred to from mplsXCTable."
::= { mplsLsrObjects 9 }
mplsXCEntry OBJECT-TYPE
SYNTAX MplsXCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents one cross-connect
entry. The following objects index it:
- cross-connect index mplsXCIndex that uniquely
identifies a group of cross-connect entries
- interface index of the in-segment,
mplsInSegmentIfIndex
- incoming label(s), mplsInSegmentLabel
- out-segment index, mplsOutSegmentIndex
Originating LSPs:
These are represented by using the special
combination of values mplsInSegmentIfIndex=0 and
mplsInSegmentLabel=0 as indexes. In this case the
mplsOutSegmentIndex MUST be non-zero.
Terminating LSPs:
These are represented by using the special value
mplsOutSegmentIndex=0 as index.
Special labels:
Entries indexed by reserved MPLS label values 0
through 15 imply terminating LSPs and MUST have
mplsOutSegmentIfIndex = 0. Note that situations
where LSPs are terminated with incoming label equal
to 0, should have mplsInSegmentIfIndex = 0 as well,
but can be distinguished from originating LSPs
because the mplsOutSegmentIfIndex = 0. The
mplsOutSegmentIfIndex MUST only be set to 0 in
cases of terminating LSPs.
An entry can be created by a network administrator
or by an SNMP agent as instructed by an MPLS
signaling protocol."
INDEX {
mplsXCIndex,
mplsInSegmentIfIndex,
mplsInSegmentLabel,
mplsOutSegmentIndex
}
::= { mplsXCTable 1 }
MplsXCEntry ::= SEQUENCE {
mplsXCIndex Unsigned32,
mplsXCLspId MplsLSPID,
mplsXCLabelStackIndex Unsigned32,
mplsXCIsPersistent TruthValue,
mplsXCOwner MplsInitialCreationSource ,
mplsXCRowStatus RowStatus,
mplsXCStorageType StorageType,
mplsXCAdminStatus INTEGER,
mplsXCOperStatus INTEGER
}
mplsXCIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Primary index for the conceptual row identifying a
group of cross-connect segments."
::= { mplsXCEntry 1 }
mplsXCLspId OBJECT-TYPE
SYNTAX MplsLSPID
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value identifies the label switched path that
this cross-connect entry belongs to. This object
cannot be modified if mplsXCRowStatus is active(1)."
::= { mplsXCEntry 2 }
mplsXCLabelStackIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Primary index into mplsLabelStackTable identifying a
stack of labels to be pushed beneath the top label.
Note that the top label identified by the out-
segment ensures that all the components of a
multipoint-to-point connection have the same
outgoing label. A value of 0 indicates that no
labels are to be stacked beneath the top label. This
object cannot be modified if mplsXCRowStatus is
active(1)."
::= { mplsXCEntry 3 }
mplsXCIsPersistent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes whether or not this cross-connect entry and
associated in- and out-segments should be restored
automatically after failures. This value MUST be
set to false in cases where this cross-connect entry
was created by a signaling protocol. This object
cannot be modified if mplsXCRowStatus is active(1)."
DEFVAL { false }
::= { mplsXCEntry 4 }
mplsXCOwner OBJECT-TYPE
SYNTAX MplsInitialCreationSource
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes the entity that created and is responsible
for managing this cross-connect. This object cannot
be modified if mplsXCRowStatus is active(1)."
::= { mplsXCEntry 5 }
mplsXCRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row."
::= { mplsXCEntry 6 }
mplsXCStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the storage type for this object. This
object cannot be modified if mplsXCRowStatus is
active(1). If this variable is set to readOnly(5),
and the corresponding TFIB entry is removed, then
the agent must remove this row shortly thereafter."
::= { mplsXCEntry 7 }
mplsXCAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1), -- ready to pass packets
down(2),
testing(3) -- in some test mode
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The desired operational status of this segment."
::= { mplsXCEntry 8 }
mplsXCOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1), -- ready to pass packets
down(2),
testing(3), -- in some test mode
unknown(4), -- status cannot be determined
-- for some reason.
dormant(5),
notPresent(6), -- some component is missing
lowerLayerDown(7) -- down due to the state of
-- lower layer interfaces
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual operational status of this cross-
connect."
::= { mplsXCEntry 9 }
-- End of mplsXCTable
-- Label stack table.
mplsMaxLabelStackDepth OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum stack depth supported by this LSR."
::= { mplsLsrObjects 10 }
mplsLabelStackIndexNext OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to be used
for mplsLabelStackIndex when creating entries in the
mplsLabelStackTable. The value 0 indicates that no
unassigned entries are available. To obtain an
mplsLabelStackIndex value for a new entry, the
manager issues a management protocol retrieval
operation to obtain the current value of this
object. After each retrieval operation, the agent
should modify the value to reflect the next
unassigned index. After a manager retrieves a value
the agent will determine through its local policy
when this index value will be made available for
reuse."
::= { mplsLsrObjects 11 }
mplsLabelStackTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLabelStackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the label stack to be pushed
onto a packet, beneath the top label. Entries into
this table are referred to from mplsXCTable."
::= { mplsLsrObjects 12 }
mplsLabelStackEntry OBJECT-TYPE
SYNTAX MplsLabelStackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents one label which is
to be pushed onto an outgoing packet, beneath the
top label. An entry can be created by a network
administrator or by an SNMP agent as instructed by
an MPLS signaling protocol."
INDEX { mplsLabelStackIndex, mplsLabelStackLabelIndex }
::= { mplsLabelStackTable 1 }
MplsLabelStackEntry ::= SEQUENCE {
mplsLabelStackIndex Unsigned32,
mplsLabelStackLabelIndex Unsigned32,
mplsLabelStackLabel MplsLabel,
mplsLabelStackRowStatus RowStatus,
mplsLabelStackStorageType StorageType
}
mplsLabelStackIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Primary index for this row identifying a stack of
labels to be pushed on an outgoing packet, beneath
the top label."
::= { mplsLabelStackEntry 1 }
mplsLabelStackLabelIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Secondary index for this row identifying one label
of the stack. Note that an entry with a smaller
mplsLabelStackLabelIndex would refer to a label
higher up the label stack and would be popped at a
downstream LSR before a label represented by a
higher mplsLabelStackLabelIndex at a downstream
LSR."
::= { mplsLabelStackEntry 2 }
mplsLabelStackLabel OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The label to pushed."
::= { mplsLabelStackEntry 3 }
mplsLabelStackRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row."
::= { mplsLabelStackEntry 4 }
mplsLabelStackStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the storage type for this object. If this
variable is set to readOnly(5), and the
corresponding TFIB entry is removed, then the agent
must remove this row shortly thereafter."
::= { mplsLabelStackEntry 5 }
-- End of mplsLabelStackTable
-- Traffic Parameter table.
mplsTrafficParamIndexNext OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value which will
be used for mplsTrafficParamIndex when creating
entries in the mplsTrafficParamTable. The value 0
indicates that no unassigned entries are available.
To obtain the mplsTrafficParamIndex value for a new
entry, the manager issues a management protocol
retrieval operation to obtain the current value of
this object. After each retrieval operation, the
agent should modify the value to reflect the next
unassigned index. After a manager retrieves a value
the agent will determine through its local policy
when this index value will be made available for
reuse."
::= { mplsLsrObjects 13 }
mplsTrafficParamTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTrafficParamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the Traffic Parameter objects
for in and out-segments."
::= { mplsLsrObjects 14 }
mplsTrafficParamEntry OBJECT-TYPE
SYNTAX MplsTrafficParamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the TrafficParam
objects for one or more in or out segments. A
single entry can be pointed to by multiple segments
indicating resource sharing."
INDEX { mplsTrafficParamIndex }
::= { mplsTrafficParamTable 1 }
MplsTrafficParamEntry ::= SEQUENCE {
mplsTrafficParamIndex Unsigned32,
mplsTrafficParamMaxRate MplsBitRate,
mplsTrafficParamMeanRate MplsBitRate,
mplsTrafficParamMaxBurstSize MplsBurstSize,
mplsTrafficParamRowStatus RowStatus,
mplsTrafficParamStorageType StorageType
}
mplsTrafficParamIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies this row of the table. Note
that zero represents an invalid index."
::= { mplsTrafficParamEntry 1 }
mplsTrafficParamMaxRate OBJECT-TYPE
SYNTAX MplsBitRate
UNITS "kilobits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum rate in kilobits/second."
::= { mplsTrafficParamEntry 2 }
mplsTrafficParamMeanRate OBJECT-TYPE
SYNTAX MplsBitRate
UNITS "kilobits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Mean rate in kilobits/second."
::= { mplsTrafficParamEntry 3 }
mplsTrafficParamMaxBurstSize OBJECT-TYPE
SYNTAX MplsBurstSize
UNITS "bytes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum burst size in bytes."
::= { mplsTrafficParamEntry 4 }
mplsTrafficParamRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For creating, modifying, and deleting this row."
::= { mplsTrafficParamEntry 5 }
mplsTrafficParamStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this object. If this variable
is set to readOnly(5), and the corresponding TFIB
entry is removed, then the agent must remove this
row shortly thereafter."
::= { mplsTrafficParamEntry 6 }
-- End of mplsTrafficParamTable
-- Notification Configuration
mplsXCTrapEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to true(1), then it enables
the emission of mplsXCUp and mplsXCDown
notifications; otherwise these notifications are not
emitted."
DEFVAL { false }
::= { mplsLsrObjects 15 }
-- Cross-connect.
mplsXCUp NOTIFICATION-TYPE
OBJECTS {
mplsXCOperStatus, -- start of range
mplsXCOperStatus -- end of range
}
STATUS current
DESCRIPTION
"This notification is generated when the
mplsXCOperStatus object for one or more contiguous
entries in mplsXCTable are about to enter the up(1)
state from some other. The included values of
mplsXCOperStatus MUST both be set equal to this
other state. The two instances of mplsXCOperStatus
in this notification indicate the range of indexes
that are affected. Note that all the indexes of the
two ends of the range can be derived from the
instance identifiers of these two objects. For
cases where a contiguous range of cross-connects
have transitioned into the up(1) state at roughly
the same time, the device SHOULD issue a single
notification for each range of contiguous indexes in
an effort to minimize the emission of a large number
of notifications. If a notification has to be
issued for just a single cross-connect entry, then
the instance identifier (and values) of the two
mplsXCOperStatus objects MUST be the identical."
::= { mplsLsrNotifyPrefix 1 }
mplsXCDown NOTIFICATION-TYPE
OBJECTS {
mplsXCOperStatus, -- start of range
mplsXCOperStatus -- end of range
}
STATUS current
DESCRIPTION
" This notification is generated when the
mplsXCOperStatus object for one or more contiguous
entries in mplsXCTable are about to enter the
down(2) state from some other. The included values
of mplsXCOperStatus MUST both be set equal to this
other state. The two instances of mplsXCOperStatus
in this notification indicate the range of indexes
that are affected. Note that all the indexes of the
two ends of the range can be derived from the
instance identifiers of these two objects. For
cases where a contiguous range of cross-connects
have transitioned into the down(2) state at roughly
the same time, the device SHOULD issue a single
notification for each range of contiguous indexes in
an effort to minimize the emission of a large number
of notifications. If a notification has to be
issued for just a single cross-connect entry, then
the instance identifier (and values) of the two
mplsXCOperStatus objects MUST be the identical."
::= { mplsLsrNotifyPrefix 2 }
-- End of notifications.
-- Module compliance.
mplsLsrGroups
OBJECT IDENTIFIER ::= { mplsLsrConformance 1 }
mplsLsrCompliances
OBJECT IDENTIFIER ::= { mplsLsrConformance 2 }
mplsLsrModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that support the
MPLS LSR MIB."
MODULE -- this module
-- The mandatory groups have to be implemented
-- by all LSRs. However, they may all be supported
-- as read-only objects in the case where manual
-- configuration is unsupported.
MANDATORY-GROUPS {
mplsInSegmentGroup,
mplsOutSegmentGroup,
mplsXCGroup,
mplsInterfaceGroup,
mplsPerfGroup,
mplsSegmentDiscontinuityGroup
}
GROUP mplsHCInSegmentPerfGroup
DESCRIPTION
"This group is mandatory for those in-segment
entries for which the object
mplsInSegmentOutOctets wraps around too
quickly."
GROUP mplsHCOutSegmentPerfGroup
DESCRIPTION
"This group is mandatory for those out-segment
entries for which the object
mplsOutSegmentOctets wraps around too quickly."
GROUP mplsTrafficParamGroup
DESCRIPTION
"This group is mandatory for those LSRs that
support QoS resource reservation."
-- Depending on whether the device implements
-- persistent cross-connects or not one of the
-- following two groups is mandatory.
GROUP mplsXCIsPersistentGroup
DESCRIPTION
"This group is mandatory for devices which
support persistent cross-connects. The
following constraints apply: mplsXCIsPersistent
must at least be read-only returning true(2)."
GROUP mplsXCIsNotPersistentGroup
DESCRIPTION
"This group is mandatory for devices which
support non-persistent cross-connects. The
following constraints apply: mplsXCIsPersistent
must at least be read-only returning false(1)."
-- mplsInSegmentTable
OBJECT mplsInSegmentXCIndex
DESCRIPTION
"Write access is not required."
OBJECT mplsInSegmentNPop
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. This object
should be set to 1 if it is read-only."
OBJECT mplsInSegmentAddrFamily
DESCRIPTION
"Write access is not required. A <value of
other(0) should be supported because there may
be cases where the agent may not know about or
support any address types."
OBJECT mplsInSegmentStorageType
SYNTAX INTEGER { other(1) }
MIN-ACCESS read-only
DESCRIPTION
"Only other(1) needs to be supported."
-- mplsOutSegmentTable
OBJECT mplsOutSegmentIfIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsOutSegmentPushTopLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsOutSegmentTopLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsOutSegmentNextHopIpAddrType
MIN-ACCESS read-only
DESCRIPTION
"ipV6(3) need not be supported."
OBJECT mplsOutSegmentNextHopIpv4Addr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsOutSegmentNextHopIpv6Addr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsOutSegmentRowStatus
SYNTAX INTEGER {
active(1),
notInService(2),
createAndGo(4),
destroy(6)
}
MIN-ACCESS read-only
DESCRIPTION
"The notReady(3) and createAndWait(5) states need
not be supported."
OBJECT mplsOutSegmentStorageType
SYNTAX INTEGER { other(1) }
MIN-ACCESS read-only
DESCRIPTION
"Only other(1) needs to be supported."
-- mplsXCTable
OBJECT mplsXCLabelStackIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsXCIsPersistent
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsXCAdminStatus
SYNTAX INTEGER { up(1), down(2) }
MIN-ACCESS read-only
DESCRIPTION
"A value of testing(3) need not be supported."
OBJECT mplsXCOperStatus
SYNTAX INTEGER { up(1), down(2) }
DESCRIPTION
"Only up(1) and down(2) need to be supported."
OBJECT mplsXCRowStatus
SYNTAX INTEGER {
active(1),
notInService(2),
createAndGo(4),
destroy(6)
}
MIN-ACCESS read-only
DESCRIPTION
"The notReady(3) and createAndWait(5) states need
not be supported."
OBJECT mplsXCStorageType
SYNTAX INTEGER { other(1) }
MIN-ACCESS read-only
DESCRIPTION
"Only other(1) needs to be supported."
::= { mplsLsrCompliances 1 }
-- Units of conformance.
mplsInterfaceGroup OBJECT-GROUP
OBJECTS {
mplsInterfaceLabelMinIn,
mplsInterfaceLabelMaxIn,
mplsInterfaceLabelMinOut,
mplsInterfaceLabelMaxOut,
mplsInterfaceTotalBandwidth,
mplsInterfaceAvailableBandwidth,
mplsInterfaceLabelParticipationType
}
STATUS current
DESCRIPTION
"Collection of objects needed for MPLS interface
configuration and performance information."
::= { mplsLsrGroups 1 }
mplsInSegmentGroup OBJECT-GROUP
OBJECTS {
mplsInSegmentNPop,
mplsInSegmentAddrFamily,
mplsInSegmentXCIndex,
mplsInSegmentOctets,
mplsInSegmentDiscards,
mplsInSegmentOwner,
mplsInSegmentRowStatus,
mplsInSegmentStorageType,
mplsInSegmentTrafficParamPtr
}
STATUS current
DESCRIPTION
"Collection of objects needed to implement an in-
segment."
::= { mplsLsrGroups 2 }
mplsOutSegmentGroup OBJECT-GROUP
OBJECTS {
mplsOutSegmentIndexNext,
mplsOutSegmentIfIndex,
mplsOutSegmentPushTopLabel,
mplsOutSegmentTopLabel,
mplsOutSegmentNextHopIpAddrType,
mplsOutSegmentNextHopIpv4Addr,
mplsOutSegmentNextHopIpv6Addr,
mplsOutSegmentXCIndex,
mplsOutSegmentOwner,
mplsOutSegmentOctets,
mplsOutSegmentDiscards,
mplsOutSegmentErrors,
mplsOutSegmentRowStatus,
mplsOutSegmentStorageType,
mplsOutSegmentTrafficParamPtr
}
STATUS current
DESCRIPTION
"Collection of objects needed to implement an out-
segment."
::= { mplsLsrGroups 3 }
mplsXCGroup OBJECT-GROUP
OBJECTS {
mplsXCIndexNext,
mplsXCLabelStackIndex,
mplsXCOwner,
mplsXCAdminStatus,
mplsXCOperStatus,
mplsXCRowStatus,
mplsXCTrapEnable,
mplsXCStorageType
}
STATUS current
DESCRIPTION
"Collection of objects needed to implement a
cross-connect entry."
::= { mplsLsrGroups 4 }
mplsXCOptionalGroup OBJECT-GROUP
OBJECTS { mplsXCLspId }
STATUS current
DESCRIPTION
"Collection of optional objects for implementing
a cross-connect entry."
::= { mplsLsrGroups 5 }
mplsPerfGroup OBJECT-GROUP
OBJECTS {
mplsInSegmentOctets,
mplsInSegmentPackets,
mplsInSegmentErrors,
mplsInSegmentDiscards,
mplsOutSegmentOctets,
mplsOutSegmentPackets,
mplsOutSegmentDiscards,
mplsInterfaceInLabelsUsed,
mplsInterfaceFailedLabelLookup,
mplsInterfaceOutFragments,
mplsInterfaceOutLabelsUsed
}
STATUS current
DESCRIPTION
"Collection of objects providing performance
information
about an LSR."
::= { mplsLsrGroups 6 }
mplsHCInSegmentPerfGroup OBJECT-GROUP
OBJECTS { mplsInSegmentHCOctets }
STATUS current
DESCRIPTION
"Object(s) providing performance information
specific to out-segments for which the object
mplsInterfaceInOctets wraps around too quickly."
::= { mplsLsrGroups 7 }
mplsHCOutSegmentPerfGroup OBJECT-GROUP
OBJECTS { mplsOutSegmentHCOctets }
STATUS current
DESCRIPTION
"Object(s) providing performance information
specific to out-segments for which the object
mplsInterfaceOutOctets wraps around too
quickly."
::= { mplsLsrGroups 8 }
mplsTrafficParamGroup OBJECT-GROUP
OBJECTS {
mplsTrafficParamIndexNext,
mplsTrafficParamMaxRate,
mplsTrafficParamMeanRate,
mplsTrafficParamMaxBurstSize,
mplsTrafficParamRowStatus,
mplsTrafficParamStorageType
}
STATUS current
DESCRIPTION
"Object(s) required for supporting QoS resource
reservation."
::= { mplsLsrGroups 9 }
mplsXCIsPersistentGroup OBJECT-GROUP
OBJECTS { mplsXCIsPersistent }
STATUS current
DESCRIPTION
"Objects needed to support persistent cross-
connects."
::= { mplsLsrGroups 10 }
mplsXCIsNotPersistentGroup OBJECT-GROUP
OBJECTS { mplsXCIsPersistent }
STATUS current
DESCRIPTION
"Objects needed to support non-persistent cross-
connects."
::= { mplsLsrGroups 11 }
mplsLabelStackGroup OBJECT-GROUP
OBJECTS {
mplsLabelStackLabel,
mplsLabelStackRowStatus,
mplsLabelStackStorageType,
mplsMaxLabelStackDepth,
mplsLabelStackIndexNext
}
STATUS current
DESCRIPTION
"Objects needed to support label stacking."
::= { mplsLsrGroups 12 }
mplsSegmentDiscontinuityGroup OBJECT-GROUP
OBJECTS {
mplsInSegmentPerfDiscontinuityTime,
mplsOutSegmentPerfDiscontinuityTime
}
STATUS current
DESCRIPTION
" A collection of objects providing information
specific to segment discontinuities.."
::= { mplsLsrGroups 13 }
mplsLsrNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
mplsXCUp,
mplsXCDown
}
STATUS current
DESCRIPTION
"Set of notifications implemented in this module.
None is mandatory."
::= { mplsLsrGroups 14 }
END