mibs/junos/JNX-OPT-IF-MIB
JNX-OPT-IF-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Gauge32, Integer32,
Unsigned32, transmission
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, RowPointer, RowStatus, TruthValue
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
jnxoptIfMibRoot
FROM JUNIPER-SMI
ifIndex
FROM IF-MIB;
--This is the MIB module for the OTN Interface objects.
jnxoptIfMibModule MODULE-IDENTITY
LAST-UPDATED "200308130000Z"
ORGANIZATION "IETF AToM MIB Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/atommib-charter.html
Mailing Lists:
General Discussion: atommib@research.telcordia.com
To Subscribe: atommib-request@research.telcordia.com
RFC 3591 Optical Interface Type MIB September 2003
Editor: Hing-Kam Lam
Postal: Lucent Technologies, Room 4C-616
101 Crawfords Corner Road
Holmdel, NJ 07733
Tel: +1 732 949 8338
Email: hklam@lucent.com"
DESCRIPTION
"The MIB module to describe pre-OTN and OTN interfaces.
Copyright (C) The Internet Society (2003). This version
of this MIB module is part of RFC 3591; see the RFC
itself for full legal notices."
REVISION "200308130000Z"
DESCRIPTION
"Initial version, published as RFC 3591."
::={ jnxoptIfMibRoot 1 }
-- textual conventions
JnxoptIfAcTI ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The trace identifier (TI) accepted at the receiver."
SYNTAX OCTET STRING (SIZE(64))
JnxoptIfBitRateK ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Indicates the index that is used to
represent a supported bit rate and the different
versions of OPUk, ODUk and OTUk.
Allowed values of k are defined in ITU-T G.709.
Currently allowed values in G.709 are:
k=1 represents an approximate bit rate of 2.5 Gbit/s,
k=2 represents an approximate bit rate of 10 Gbit/s,
k=3 represents an approximate bit rate of 40 Gbit/s."
SYNTAX Integer32
JnxoptIfDEGM ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if JnxoptIfDEGM
consecutive bad PM Seconds are detected."
SYNTAX Unsigned32 (2..10)
JnxoptIfDEGThr ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to JnxoptIfDEGThr."
SYNTAX Unsigned32 (1..100)
JnxoptIfDirectionality ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Indicates the directionality of an entity."
SYNTAX INTEGER {
sink(1),
source(2),
bidirectional(3)
}
JnxoptIfSinkOrSource ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Indicates the directionality of an entity
that is allowed only to be a source or sink."
SYNTAX INTEGER {
sink(1),
source(2)
}
JnxoptIfExDAPI ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The Destination Access Point Identifier (DAPI)
expected by the receiver."
SYNTAX OCTET STRING (SIZE(16))
JnxoptIfExSAPI ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The Source Access Point Identifier (SAPI)
expected by the receiver."
SYNTAX OCTET STRING (SIZE(16))
JnxoptIfIntervalNumber ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Uniquely identifies a 15-minute interval. The interval
identified by 1 is the most recently completed interval, and
the interval identified by n is the interval immediately
preceding the one identified by n-1."
SYNTAX Unsigned32 (1..96)
JnxoptIfTIMDetMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function."
SYNTAX INTEGER {
off(1),
dapi(2),
sapi(3),
both(4)
}
JnxoptIfTxTI ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The trace identifier (TI) transmitted."
SYNTAX OCTET STRING (SIZE(64))
-- object groups
jnxoptIfObjects OBJECT IDENTIFIER ::= { jnxoptIfMibModule 1 }
jnxoptIfConfs OBJECT IDENTIFIER ::= { jnxoptIfMibModule 2 }
jnxoptIfOTMn OBJECT IDENTIFIER ::= { jnxoptIfObjects 1 }
jnxoptIfPerfMon OBJECT IDENTIFIER ::= { jnxoptIfObjects 2 }
jnxoptIfOTSn OBJECT IDENTIFIER ::= { jnxoptIfObjects 3 }
jnxoptIfOMSn OBJECT IDENTIFIER ::= { jnxoptIfObjects 4 }
jnxoptIfOChGroup OBJECT IDENTIFIER ::= { jnxoptIfObjects 5 }
jnxoptIfOCh OBJECT IDENTIFIER ::= { jnxoptIfObjects 6 }
jnxoptIfOTUk OBJECT IDENTIFIER ::= { jnxoptIfObjects 7 }
jnxoptIfODUk OBJECT IDENTIFIER ::= { jnxoptIfObjects 8 }
jnxoptIfODUkT OBJECT IDENTIFIER ::= { jnxoptIfObjects 9 }
jnxoptIfGroups OBJECT IDENTIFIER ::= { jnxoptIfConfs 1 }
jnxoptIfCompl OBJECT IDENTIFIER ::= { jnxoptIfConfs 2 }
-- the jnxoptIfOTMn group
-- This group defines the OTM structure information of an
-- optical interface.
-- OTMn Table
jnxoptIfOTMnTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTMnEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTMn structure information."
::= { jnxoptIfOTMn 1 }
jnxoptIfOTMnEntry OBJECT-TYPE
SYNTAX JnxoptIfOTMnEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains the OTMn structure
information of an optical interface."
INDEX { ifIndex }
::= { jnxoptIfOTMnTable 1 }
JnxoptIfOTMnEntry ::=
SEQUENCE {
jnxoptIfOTMnOrder Unsigned32,
jnxoptIfOTMnReduced TruthValue,
jnxoptIfOTMnBitRates BITS,
jnxoptIfOTMnInterfaceType SnmpAdminString,
jnxoptIfOTMnTcmMax Unsigned32,
jnxoptIfOTMnOpticalReach INTEGER
}
jnxoptIfOTMnOrder OBJECT-TYPE
SYNTAX Unsigned32 (1..900)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the order of the OTM, which
represents the maximum number of wavelengths that can be
supported at the bit rate(s) supported on the interface."
::= { jnxoptIfOTMnEntry 1 }
jnxoptIfOTMnReduced OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether a reduced or full
functionality is supported at the interface. A value of
true means reduced. A value of false means full."
::= { jnxoptIfOTMnEntry 2 }
jnxoptIfOTMnBitRates OBJECT-TYPE
SYNTAX BITS { bitRateK1(0), bitRateK2(1), bitRateK3(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute is a bit map representing the bit
rate or set of bit rates supported on the interface.
The meaning of each bit position is as follows:
bitRateK1(0) is set if the 2.5 Gbit/s rate is supported
bitRateK2(1) is set if the 10 Gbit/s rate is supported
bitRateK3(2) is set if the 40 Gbit/s rate is supported
Note that each bit position corresponds to one possible
value of the type JnxoptIfBitRateK.
The default value of this attribute is system specific."
::= { jnxoptIfOTMnEntry 3 }
jnxoptIfOTMnInterfaceType OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the type of interface. The value of
this attribute will affect the behavior of the OTM with
respect to presence/absence of OTM Overhead Signal (OOS)
processing and TCM activation. For an IrDI interface,
there is no OOS processing and TCM activation is limited
to n levels as specified by a TCM level threshold.
This object contains two fields that are separated by
whitespace. The possible values are:
field 1: one of the 4-character ASCII strings
'IrDI' or 'IaDI'
field 2: free-form text consisting of printable
UTF-8 encoded characters
Note that field 2 is optional. If it is not present then there
is no requirement for trailing whitespace after field 1.
The default values are as follows:
field 1: 'IaDI' field 2: an empty string."
::= { jnxoptIfOTMnEntry 4 }
jnxoptIfOTMnTcmMax OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object identifies the maximum number of TCM
levels allowed for any Optical Channel contained
in this OTM. A new TCM activation will be rejected
if the requested level is greater than the threshold.
If InterfaceType object specifies a type of 'IaDI'
for this OTM, then this attribute is irrelevant.
Possible values: unsigned integers in the range
from 0 to 6 inclusive.
Default value: 3."
::= { jnxoptIfOTMnEntry 5 }
jnxoptIfOTMnOpticalReach OBJECT-TYPE
SYNTAX INTEGER { intraOffice(1), shortHaul(2), longHaul(3),
veryLongHaul(4), ultraLongHaul(5) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the length the optical signal
may travel before requiring termination or regeneration.
The meaning of the enumeration are:
intraOffice(1) - intra-office (as defined in ITU-T G.957)
shortHaul(2) - short haul (as defined in ITU-T G.957)
longHaul(3) - long haul (as defined in ITU-T G.957)
veryLongHaul(4) - very long haul (as defined in ITU-T G.691)
ultraLongHaul(5)- ultra long haul (as defined in ITU-T G.691)"
::= { jnxoptIfOTMnEntry 6 }
-- the jnxoptIfPerfMon group
-- This group defines performance monitoring objects for all
-- layers.
-- PM interval table
jnxoptIfPerfMonIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfPerfMonIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of 15-minute performance monitoring interval
information."
::= { jnxoptIfPerfMon 1 }
jnxoptIfPerfMonIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfPerfMonIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains 15-minute performance
monitoring interval information of an interface."
INDEX { ifIndex }
::= { jnxoptIfPerfMonIntervalTable 1 }
JnxoptIfPerfMonIntervalEntry ::=
SEQUENCE {
jnxoptIfPerfMonCurrentTimeElapsed Gauge32,
jnxoptIfPerfMonCurDayTimeElapsed Gauge32,
jnxoptIfPerfMonIntervalNumIntervals Unsigned32,
jnxoptIfPerfMonIntervalNumInvalidIntervals Unsigned32
}
jnxoptIfPerfMonCurrentTimeElapsed OBJECT-TYPE
SYNTAX Gauge32 (0..900)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds elapsed in the current 15-minute
performance monitoring interval.
If, for some reason, such as an adjustment in the NE's
time-of-day clock, the number of seconds elapsed exceeds
the maximum value, then the maximum value will be returned."
::= { jnxoptIfPerfMonIntervalEntry 1 }
jnxoptIfPerfMonCurDayTimeElapsed OBJECT-TYPE
SYNTAX Gauge32 (0..86400)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds elapsed in the current 24-hour interval
performance monitoring period.
If, for some reason, such as an adjustment in the NE
time-of-day clock, the number of seconds elapsed exceeds
the maximum value, then the maximum value will be returned."
::= { jnxoptIfPerfMonIntervalEntry 2 }
jnxoptIfPerfMonIntervalNumIntervals OBJECT-TYPE
SYNTAX Unsigned32 (0..96)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of 15-minute intervals for which performance
monitoring data is available. The number is the same for all
the associated sub layers of the interface.
An optical interface must be capable of supporting at least
n intervals, where n is defined as follows:
The minimum value of n is 4.
The default of n is 32.
The maximum value of n is 96.
The value of this object will be n unless performance
monitoring was (re-)started for the interface within the last
(n*15) minutes, in which case the value will be the number of
complete 15-minute intervals since measurement was
(re-)started."
::= { jnxoptIfPerfMonIntervalEntry 3 }
jnxoptIfPerfMonIntervalNumInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32 (0..96)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of intervals in the range from 0 to
jnxoptIfPerfMonIntervalNumIntervals for which no performance
monitoring data is available and/or the data is invalid."
::= { jnxoptIfPerfMonIntervalEntry 4 }
-- the jnxoptIfOTSn group
-- This group handles the configuration and performance
-- monitoring objects for OTS layers.
-- OTSn config table
jnxoptIfOTSnConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTSn configuration information."
::= { jnxoptIfOTSn 1 }
jnxoptIfOTSnConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn configuration
information of an interface."
INDEX { ifIndex }
::= { jnxoptIfOTSnConfigTable 1 }
JnxoptIfOTSnConfigEntry ::=
SEQUENCE {
jnxoptIfOTSnDirectionality JnxoptIfDirectionality,
jnxoptIfOTSnAprStatus SnmpAdminString,
jnxoptIfOTSnAprControl SnmpAdminString,
jnxoptIfOTSnTraceIdentifierTransmitted JnxoptIfTxTI,
jnxoptIfOTSnDAPIExpected JnxoptIfExDAPI,
jnxoptIfOTSnSAPIExpected JnxoptIfExSAPI,
jnxoptIfOTSnTraceIdentifierAccepted JnxoptIfAcTI,
jnxoptIfOTSnTIMDetMode JnxoptIfTIMDetMode,
jnxoptIfOTSnTIMActEnabled TruthValue,
jnxoptIfOTSnCurrentStatus BITS
}
jnxoptIfOTSnDirectionality OBJECT-TYPE
SYNTAX JnxoptIfDirectionality
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the directionality of the entity."
::= { jnxoptIfOTSnConfigEntry 1 }
jnxoptIfOTSnAprStatus OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute indicates the status of the Automatic
Power Reduction (APR) function of the entity. Valid
values are 'on' and 'off'."
::= { jnxoptIfOTSnConfigEntry 2 }
jnxoptIfOTSnAprControl OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is a UTF-8 encoded string that specifies Automatic
Power Reduction (APR) control actions requested of this entity
(when written) and that returns the current APR control state
of this entity (when read). The values are implementation-defined.
Any implementation that instantiates this object must document the
set of values that it allows to be written, the set of values
that it will return, and what each of those values means."
::= { jnxoptIfOTSnConfigEntry 3 }
jnxoptIfOTSnTraceIdentifierTransmitted OBJECT-TYPE
SYNTAX JnxoptIfTxTI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The trace identifier transmitted.
This object is applicable when jnxoptIfOTSnDirectionality has the
value source(2) or bidirectional(3).
This object does not apply to reduced-capability systems (i.e.,
those for which jnxoptIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1
has the value 'IrDI').
If no value is ever set by a management entity for the object
jnxoptIfOTSnTraceIdentifierTransmitted, system-specific default
value will be used. Any implementation that instantiates this
object must document the system-specific default value or how it
is derived."
::= { jnxoptIfOTSnConfigEntry 4 }
jnxoptIfOTSnDAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExDAPI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DAPI expected by the receiver.
This object is applicable when jnxoptIfOTSnDirectionality has the
value sink(1) or bidirectional(3). It has no effect if
jnxoptIfOTSnTIMDetMode has the value off(1) or sapi(3).
This object does not apply to reduced-capability systems (i.e.,
those for which jnxoptIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1
has the value 'IrDI')."
::= { jnxoptIfOTSnConfigEntry 5 }
jnxoptIfOTSnSAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExSAPI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The SAPI expected by the receiver.
This object is applicable when jnxoptIfOTSnDirectionality has the
value sink(1) or bidirectional(3). It has no effect if
jnxoptIfOTSnTIMDetMode has the value off(1) or dapi(2).
This object does not apply to reduced-capability systems (i.e.,
those for which jnxoptIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1
has the value 'IrDI')."
::= { jnxoptIfOTSnConfigEntry 6 }
jnxoptIfOTSnTraceIdentifierAccepted OBJECT-TYPE
SYNTAX JnxoptIfAcTI
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual trace identifier received.
This object is applicable when jnxoptIfOTSnDirectionality has the
value sink(1) or bidirectional(3). Its value is unspecified
if jnxoptIfOTSnCurrentStatus has either or both of the
losO(5) and los(6) bits set.
This object does not apply to reduced-capability systems (i.e.,
those for which jnxoptIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1
has the value 'IrDI')."
::= { jnxoptIfOTSnConfigEntry 7 }
jnxoptIfOTSnTIMDetMode OBJECT-TYPE
SYNTAX JnxoptIfTIMDetMode
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function. This object is applicable
when jnxoptIfOTSnDirectionality has the value sink(1)
or bidirectional(3). The default value is off(1).
This object does not apply to reduced-capability systems (i.e.,
those for which jnxoptIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1
has the value 'IrDI').
The default value of this object is off(1)."
::= { jnxoptIfOTSnConfigEntry 8 }
jnxoptIfOTSnTIMActEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled. This object
is applicable when jnxoptIfOTSnDirectionality has the
value sink(1) or bidirectional(3). It has no effect
when the value of jnxoptIfOTSnTIMDetMode is off(1).
This object does not apply to reduced-capability systems (i.e.,
those for which jnxoptIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1
has the value 'IrDI').
The default value of this object is false(2)."
::= { jnxoptIfOTSnConfigEntry 9 }
jnxoptIfOTSnCurrentStatus OBJECT-TYPE
SYNTAX BITS {
bdiP(0),
bdiO(1),
bdi(2),
tim(3),
losP(4),
losO(5),
los(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the defect condition of the entity, if any.
This object is applicable when jnxoptIfOTSnDirectionality
has the value sink(1) or bidirectional(3). In
reduced-capability systems or at IrDI interfaces
the only bit position that may be set is los(6)."
::= { jnxoptIfOTSnConfigEntry 10 }
-- OTSn sink current table
-- Contains data for the current 15-minute performance monitoring
-- interval.
jnxoptIfOTSnSinkCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnSinkCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTSn sink performance monitoring information for
the current 15-minute interval."
::= { jnxoptIfOTSn 2 }
jnxoptIfOTSnSinkCurrentEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnSinkCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn sink performance
monitoring information of an interface for the current
15-minute interval."
INDEX { ifIndex }
::= { jnxoptIfOTSnSinkCurrentTable 1 }
JnxoptIfOTSnSinkCurrentEntry ::=
SEQUENCE {
jnxoptIfOTSnSinkCurrentSuspectedFlag TruthValue,
jnxoptIfOTSnSinkCurrentInputPower Integer32,
jnxoptIfOTSnSinkCurrentLowInputPower Integer32,
jnxoptIfOTSnSinkCurrentHighInputPower Integer32,
jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold Integer32,
jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold Integer32,
jnxoptIfOTSnSinkCurrentOutputPower Integer32,
jnxoptIfOTSnSinkCurrentLowOutputPower Integer32,
jnxoptIfOTSnSinkCurrentHighOutputPower Integer32,
jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold Integer32,
jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold Integer32
}
jnxoptIfOTSnSinkCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOTSnSinkCurrentEntry 1 }
jnxoptIfOTSnSinkCurrentInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the input."
::= { jnxoptIfOTSnSinkCurrentEntry 2 }
jnxoptIfOTSnSinkCurrentLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
current 15-minute interval."
::= { jnxoptIfOTSnSinkCurrentEntry 3 }
jnxoptIfOTSnSinkCurrentHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
current 15-minute interval."
::= { jnxoptIfOTSnSinkCurrentEntry 4 }
jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on input power. If
jnxoptIfOTSnSinkCurrentInputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOTSnSinkCurrentEntry 5 }
jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on input power. If
jnxoptIfOTSnSinkCurrentInputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOTSnSinkCurrentEntry 6 }
jnxoptIfOTSnSinkCurrentOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the output."
::= { jnxoptIfOTSnSinkCurrentEntry 7 }
jnxoptIfOTSnSinkCurrentLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOTSnSinkCurrentEntry 8 }
jnxoptIfOTSnSinkCurrentHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOTSnSinkCurrentEntry 9 }
jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on output power. If
jnxoptIfOTSnSinkCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOTSnSinkCurrentEntry 10 }
jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on output power. If
jnxoptIfOTSnSinkCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOTSnSinkCurrentEntry 11 }
-- OTSn sink interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.
jnxoptIfOTSnSinkIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnSinkIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of historical OTSn sink performance monitoring
information."
::= { jnxoptIfOTSn 3 }
jnxoptIfOTSnSinkIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnSinkIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn sink performance
monitoring information of an interface during a particular
historical interval."
INDEX { ifIndex, jnxoptIfOTSnSinkIntervalNumber }
::= { jnxoptIfOTSnSinkIntervalTable 1 }
JnxoptIfOTSnSinkIntervalEntry ::=
SEQUENCE {
jnxoptIfOTSnSinkIntervalNumber JnxoptIfIntervalNumber,
jnxoptIfOTSnSinkIntervalSuspectedFlag TruthValue,
jnxoptIfOTSnSinkIntervalLastInputPower Integer32,
jnxoptIfOTSnSinkIntervalLowInputPower Integer32,
jnxoptIfOTSnSinkIntervalHighInputPower Integer32,
jnxoptIfOTSnSinkIntervalLastOutputPower Integer32,
jnxoptIfOTSnSinkIntervalLowOutputPower Integer32,
jnxoptIfOTSnSinkIntervalHighOutputPower Integer32
}
jnxoptIfOTSnSinkIntervalNumber OBJECT-TYPE
SYNTAX JnxoptIfIntervalNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies the interval."
::= { jnxoptIfOTSnSinkIntervalEntry 1 }
jnxoptIfOTSnSinkIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOTSnSinkIntervalEntry 2 }
jnxoptIfOTSnSinkIntervalLastInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the input during the
interval."
::= { jnxoptIfOTSnSinkIntervalEntry 3 }
jnxoptIfOTSnSinkIntervalLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
interval."
::= { jnxoptIfOTSnSinkIntervalEntry 4 }
jnxoptIfOTSnSinkIntervalHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
interval."
::= { jnxoptIfOTSnSinkIntervalEntry 5 }
jnxoptIfOTSnSinkIntervalLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
interval."
::= { jnxoptIfOTSnSinkIntervalEntry 6 }
jnxoptIfOTSnSinkIntervalLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
interval."
::= { jnxoptIfOTSnSinkIntervalEntry 7 }
jnxoptIfOTSnSinkIntervalHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
interval."
::= { jnxoptIfOTSnSinkIntervalEntry 8 }
-- OTSn sink current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.
jnxoptIfOTSnSinkCurDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnSinkCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTSn sink performance monitoring information for
the current 24-hour interval."
::= { jnxoptIfOTSn 4 }
jnxoptIfOTSnSinkCurDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnSinkCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn sink performance
monitoring information of an interface for the current
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOTSnSinkCurDayTable 1 }
JnxoptIfOTSnSinkCurDayEntry ::=
SEQUENCE {
jnxoptIfOTSnSinkCurDaySuspectedFlag TruthValue,
jnxoptIfOTSnSinkCurDayLowInputPower Integer32,
jnxoptIfOTSnSinkCurDayHighInputPower Integer32,
jnxoptIfOTSnSinkCurDayLowOutputPower Integer32,
jnxoptIfOTSnSinkCurDayHighOutputPower Integer32
}
jnxoptIfOTSnSinkCurDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOTSnSinkCurDayEntry 1 }
jnxoptIfOTSnSinkCurDayLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
current 24-hour interval."
::= { jnxoptIfOTSnSinkCurDayEntry 2 }
jnxoptIfOTSnSinkCurDayHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
current 24-hour interval."
::= { jnxoptIfOTSnSinkCurDayEntry 3 }
jnxoptIfOTSnSinkCurDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOTSnSinkCurDayEntry 4 }
jnxoptIfOTSnSinkCurDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOTSnSinkCurDayEntry 5 }
-- OTSn sink previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.
jnxoptIfOTSnSinkPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnSinkPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTSn sink performance monitoring information for
the previous 24-hour interval."
::= { jnxoptIfOTSn 5 }
jnxoptIfOTSnSinkPrevDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnSinkPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn sink performance
monitoring information of an interface for the previous
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOTSnSinkPrevDayTable 1 }
JnxoptIfOTSnSinkPrevDayEntry ::=
SEQUENCE {
jnxoptIfOTSnSinkPrevDaySuspectedFlag TruthValue,
jnxoptIfOTSnSinkPrevDayLastInputPower Integer32,
jnxoptIfOTSnSinkPrevDayLowInputPower Integer32,
jnxoptIfOTSnSinkPrevDayHighInputPower Integer32,
jnxoptIfOTSnSinkPrevDayLastOutputPower Integer32,
jnxoptIfOTSnSinkPrevDayLowOutputPower Integer32,
jnxoptIfOTSnSinkPrevDayHighOutputPower Integer32
}
jnxoptIfOTSnSinkPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOTSnSinkPrevDayEntry 1 }
jnxoptIfOTSnSinkPrevDayLastInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOTSnSinkPrevDayEntry 2 }
jnxoptIfOTSnSinkPrevDayLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOTSnSinkPrevDayEntry 3 }
jnxoptIfOTSnSinkPrevDayHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOTSnSinkPrevDayEntry 4 }
jnxoptIfOTSnSinkPrevDayLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOTSnSinkPrevDayEntry 5 }
jnxoptIfOTSnSinkPrevDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOTSnSinkPrevDayEntry 6 }
jnxoptIfOTSnSinkPrevDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOTSnSinkPrevDayEntry 7 }
-- OTSn source current table
-- Contains data for the current 15-minute performance monitoring
-- interval.
jnxoptIfOTSnSrcCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnSrcCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTSn source performance monitoring information for
the current 15-minute interval."
::= { jnxoptIfOTSn 6 }
jnxoptIfOTSnSrcCurrentEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnSrcCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn source performance
monitoring information of an interface for the current
15-minute interval."
INDEX { ifIndex }
::= { jnxoptIfOTSnSrcCurrentTable 1 }
JnxoptIfOTSnSrcCurrentEntry ::=
SEQUENCE {
jnxoptIfOTSnSrcCurrentSuspectedFlag TruthValue,
jnxoptIfOTSnSrcCurrentOutputPower Integer32,
jnxoptIfOTSnSrcCurrentLowOutputPower Integer32,
jnxoptIfOTSnSrcCurrentHighOutputPower Integer32,
jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold Integer32,
jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold Integer32,
jnxoptIfOTSnSrcCurrentInputPower Integer32,
jnxoptIfOTSnSrcCurrentLowInputPower Integer32,
jnxoptIfOTSnSrcCurrentHighInputPower Integer32,
jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold Integer32,
jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold Integer32
}
jnxoptIfOTSnSrcCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOTSnSrcCurrentEntry 1 }
jnxoptIfOTSnSrcCurrentOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the output."
::= { jnxoptIfOTSnSrcCurrentEntry 2 }
jnxoptIfOTSnSrcCurrentLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOTSnSrcCurrentEntry 3 }
jnxoptIfOTSnSrcCurrentHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOTSnSrcCurrentEntry 4 }
jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on output power. If
jnxoptIfOTSnSrcCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOTSnSrcCurrentEntry 5 }
jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on output power. If
jnxoptIfOTSnSrcCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOTSnSrcCurrentEntry 6 }
jnxoptIfOTSnSrcCurrentInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the input."
::= { jnxoptIfOTSnSrcCurrentEntry 7 }
jnxoptIfOTSnSrcCurrentLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
current 15-minute interval."
::= { jnxoptIfOTSnSrcCurrentEntry 8 }
jnxoptIfOTSnSrcCurrentHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
current 15-minute interval."
::= { jnxoptIfOTSnSrcCurrentEntry 9 }
jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on input power. If
jnxoptIfOTSnSrcCurrentInputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOTSnSrcCurrentEntry 10 }
jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on input power. If
jnxoptIfOTSnSrcCurrentInputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOTSnSrcCurrentEntry 11 }
-- OTSn source interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.
jnxoptIfOTSnSrcIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnSrcIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of historical OTSn source performance monitoring
information."
::= { jnxoptIfOTSn 7 }
jnxoptIfOTSnSrcIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnSrcIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn source performance
monitoring information of an interface during a particular
historical interval."
INDEX { ifIndex, jnxoptIfOTSnSrcIntervalNumber }
::= { jnxoptIfOTSnSrcIntervalTable 1 }
JnxoptIfOTSnSrcIntervalEntry ::=
SEQUENCE {
jnxoptIfOTSnSrcIntervalNumber JnxoptIfIntervalNumber,
jnxoptIfOTSnSrcIntervalSuspectedFlag TruthValue,
jnxoptIfOTSnSrcIntervalLastOutputPower Integer32,
jnxoptIfOTSnSrcIntervalLowOutputPower Integer32,
jnxoptIfOTSnSrcIntervalHighOutputPower Integer32,
jnxoptIfOTSnSrcIntervalLastInputPower Integer32,
jnxoptIfOTSnSrcIntervalLowInputPower Integer32,
jnxoptIfOTSnSrcIntervalHighInputPower Integer32
}
jnxoptIfOTSnSrcIntervalNumber OBJECT-TYPE
SYNTAX JnxoptIfIntervalNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies the interval."
::= { jnxoptIfOTSnSrcIntervalEntry 1 }
jnxoptIfOTSnSrcIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOTSnSrcIntervalEntry 2 }
jnxoptIfOTSnSrcIntervalLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
interval."
::= { jnxoptIfOTSnSrcIntervalEntry 3 }
jnxoptIfOTSnSrcIntervalLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
interval."
::= { jnxoptIfOTSnSrcIntervalEntry 4 }
jnxoptIfOTSnSrcIntervalHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
interval."
::= { jnxoptIfOTSnSrcIntervalEntry 5 }
jnxoptIfOTSnSrcIntervalLastInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the input during the
interval."
::= { jnxoptIfOTSnSrcIntervalEntry 6 }
jnxoptIfOTSnSrcIntervalLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
interval."
::= { jnxoptIfOTSnSrcIntervalEntry 7 }
jnxoptIfOTSnSrcIntervalHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
interval."
::= { jnxoptIfOTSnSrcIntervalEntry 8 }
-- OTSn source current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.
jnxoptIfOTSnSrcCurDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnSrcCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTSn source performance monitoring information for
the current 24-hour interval."
::= { jnxoptIfOTSn 8 }
jnxoptIfOTSnSrcCurDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnSrcCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn source performance
monitoring information of an interface for the current
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOTSnSrcCurDayTable 1 }
JnxoptIfOTSnSrcCurDayEntry ::=
SEQUENCE {
jnxoptIfOTSnSrcCurDaySuspectedFlag TruthValue,
jnxoptIfOTSnSrcCurDayLowOutputPower Integer32,
jnxoptIfOTSnSrcCurDayHighOutputPower Integer32,
jnxoptIfOTSnSrcCurDayLowInputPower Integer32,
jnxoptIfOTSnSrcCurDayHighInputPower Integer32
}
jnxoptIfOTSnSrcCurDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOTSnSrcCurDayEntry 1 }
jnxoptIfOTSnSrcCurDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOTSnSrcCurDayEntry 2 }
jnxoptIfOTSnSrcCurDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOTSnSrcCurDayEntry 3 }
jnxoptIfOTSnSrcCurDayLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
current 24-hour interval."
::= { jnxoptIfOTSnSrcCurDayEntry 4 }
jnxoptIfOTSnSrcCurDayHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
current 24-hour interval."
::= { jnxoptIfOTSnSrcCurDayEntry 5 }
-- OTSn source previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.
jnxoptIfOTSnSrcPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTSnSrcPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTSn source performance monitoring information for
the previous 24-hour interval."
::= { jnxoptIfOTSn 9 }
jnxoptIfOTSnSrcPrevDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOTSnSrcPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTSn source performance
monitoring information of an interface for the previous
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOTSnSrcPrevDayTable 1 }
JnxoptIfOTSnSrcPrevDayEntry ::=
SEQUENCE {
jnxoptIfOTSnSrcPrevDaySuspectedFlag TruthValue,
jnxoptIfOTSnSrcPrevDayLastOutputPower Integer32,
jnxoptIfOTSnSrcPrevDayLowOutputPower Integer32,
jnxoptIfOTSnSrcPrevDayHighOutputPower Integer32,
jnxoptIfOTSnSrcPrevDayLastInputPower Integer32,
jnxoptIfOTSnSrcPrevDayLowInputPower Integer32,
jnxoptIfOTSnSrcPrevDayHighInputPower Integer32
}
jnxoptIfOTSnSrcPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOTSnSrcPrevDayEntry 1 }
jnxoptIfOTSnSrcPrevDayLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOTSnSrcPrevDayEntry 2 }
jnxoptIfOTSnSrcPrevDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOTSnSrcPrevDayEntry 3 }
jnxoptIfOTSnSrcPrevDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOTSnSrcPrevDayEntry 4 }
jnxoptIfOTSnSrcPrevDayLastInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOTSnSrcPrevDayEntry 5 }
jnxoptIfOTSnSrcPrevDayLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOTSnSrcPrevDayEntry 6 }
jnxoptIfOTSnSrcPrevDayHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOTSnSrcPrevDayEntry 7 }
-- the jnxoptIfOMSn group
-- This group handles the configuration and performance monitoring
-- information for OMS layers.
-- OMSn config table
jnxoptIfOMSnConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OMSn configuration information."
::= { jnxoptIfOMSn 1 }
jnxoptIfOMSnConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn configuration
information of an interface."
INDEX { ifIndex }
::= { jnxoptIfOMSnConfigTable 1 }
JnxoptIfOMSnConfigEntry ::=
SEQUENCE {
jnxoptIfOMSnDirectionality JnxoptIfDirectionality,
jnxoptIfOMSnCurrentStatus BITS
}
jnxoptIfOMSnDirectionality OBJECT-TYPE
SYNTAX JnxoptIfDirectionality
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the directionality of the entity."
::= { jnxoptIfOMSnConfigEntry 1 }
jnxoptIfOMSnCurrentStatus OBJECT-TYPE
SYNTAX BITS {
ssfP(0),
ssfO(1),
ssf(2),
bdiP(3),
bdiO(4),
bdi(5),
losP(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the defect condition of the entity, if any.
This object is applicable only to full capability
systems whose interface type is IaDI and for which
jnxoptIfOMSnDirectionality has the value sink(1) or
bidirectional(3)."
::= { jnxoptIfOMSnConfigEntry 2 }
-- OMSn sink current table
-- Contains data for the current 15-minute performance monitoring
-- interval.
jnxoptIfOMSnSinkCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnSinkCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OMSn sink performance monitoring information for
the current 15-minute interval."
::= { jnxoptIfOMSn 2 }
jnxoptIfOMSnSinkCurrentEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnSinkCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn sink performance
monitoring information of an interface for the current
15-minute interval."
INDEX { ifIndex }
::= { jnxoptIfOMSnSinkCurrentTable 1 }
JnxoptIfOMSnSinkCurrentEntry ::=
SEQUENCE {
jnxoptIfOMSnSinkCurrentSuspectedFlag TruthValue,
jnxoptIfOMSnSinkCurrentAggregatedInputPower Integer32,
jnxoptIfOMSnSinkCurrentLowAggregatedInputPower Integer32,
jnxoptIfOMSnSinkCurrentHighAggregatedInputPower Integer32,
jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold Integer32,
jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold Integer32,
jnxoptIfOMSnSinkCurrentOutputPower Integer32,
jnxoptIfOMSnSinkCurrentLowOutputPower Integer32,
jnxoptIfOMSnSinkCurrentHighOutputPower Integer32,
jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold Integer32,
jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold Integer32
}
jnxoptIfOMSnSinkCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOMSnSinkCurrentEntry 1 }
jnxoptIfOMSnSinkCurrentAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The aggregated optical power of all the DWDM input
channels."
::= { jnxoptIfOMSnSinkCurrentEntry 2 }
jnxoptIfOMSnSinkCurrentLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power of all the DWDM input
channels during the current 15-minute interval."
::= { jnxoptIfOMSnSinkCurrentEntry 3 }
jnxoptIfOMSnSinkCurrentHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power of all the DWDM input
channels during the current 15-minute interval."
::= { jnxoptIfOMSnSinkCurrentEntry 4 }
jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on aggregated input power. If
jnxoptIfOMSnSinkCurrentAggregatedInputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOMSnSinkCurrentEntry 5 }
jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on aggregated input power. If
jnxoptIfOMSnSinkCurrentAggregatedInputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOMSnSinkCurrentEntry 6 }
jnxoptIfOMSnSinkCurrentOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the output."
::= { jnxoptIfOMSnSinkCurrentEntry 7 }
jnxoptIfOMSnSinkCurrentLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output
during the current 15-minute interval."
::= { jnxoptIfOMSnSinkCurrentEntry 8 }
jnxoptIfOMSnSinkCurrentHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output
during the current 15-minute interval."
::= { jnxoptIfOMSnSinkCurrentEntry 9 }
jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on output power. If
jnxoptIfOMSnSinkCurrentOutputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOMSnSinkCurrentEntry 10 }
jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on output power. If
jnxoptIfOMSnSinkCurrentOutputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOMSnSinkCurrentEntry 11 }
-- OMSn sink interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.
jnxoptIfOMSnSinkIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnSinkIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of historical OMSn sink performance monitoring
information."
::= { jnxoptIfOMSn 3 }
jnxoptIfOMSnSinkIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnSinkIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn sink performance
monitoring information of an interface during a particular
historical interval."
INDEX { ifIndex, jnxoptIfOMSnSinkIntervalNumber }
::= { jnxoptIfOMSnSinkIntervalTable 1 }
JnxoptIfOMSnSinkIntervalEntry ::=
SEQUENCE {
jnxoptIfOMSnSinkIntervalNumber JnxoptIfIntervalNumber,
jnxoptIfOMSnSinkIntervalSuspectedFlag TruthValue,
jnxoptIfOMSnSinkIntervalLastAggregatedInputPower Integer32,
jnxoptIfOMSnSinkIntervalLowAggregatedInputPower Integer32,
jnxoptIfOMSnSinkIntervalHighAggregatedInputPower Integer32,
jnxoptIfOMSnSinkIntervalLastOutputPower Integer32,
jnxoptIfOMSnSinkIntervalLowOutputPower Integer32,
jnxoptIfOMSnSinkIntervalHighOutputPower Integer32
}
jnxoptIfOMSnSinkIntervalNumber OBJECT-TYPE
SYNTAX JnxoptIfIntervalNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies the interval."
::= { jnxoptIfOMSnSinkIntervalEntry 1 }
jnxoptIfOMSnSinkIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOMSnSinkIntervalEntry 2 }
jnxoptIfOMSnSinkIntervalLastAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last aggregated optical power of all the DWDM input
channels during the interval."
::= { jnxoptIfOMSnSinkIntervalEntry 3 }
jnxoptIfOMSnSinkIntervalLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power of all the DWDM input
channels during the interval."
::= { jnxoptIfOMSnSinkIntervalEntry 4 }
jnxoptIfOMSnSinkIntervalHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power of all the DWDM input
channels during the interval."
::= { jnxoptIfOMSnSinkIntervalEntry 5 }
jnxoptIfOMSnSinkIntervalLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power at the output
during the interval."
::= { jnxoptIfOMSnSinkIntervalEntry 6 }
jnxoptIfOMSnSinkIntervalLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power at the output
during the interval."
::= { jnxoptIfOMSnSinkIntervalEntry 7 }
jnxoptIfOMSnSinkIntervalHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power at the output
during the interval."
::= { jnxoptIfOMSnSinkIntervalEntry 8 }
-- OMSn sink current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.
jnxoptIfOMSnSinkCurDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnSinkCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OMSn sink performance monitoring information for
the current 24-hour interval."
::= { jnxoptIfOMSn 4 }
jnxoptIfOMSnSinkCurDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnSinkCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn sink performance
monitoring information of an interface for the current
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOMSnSinkCurDayTable 1 }
JnxoptIfOMSnSinkCurDayEntry ::=
SEQUENCE {
jnxoptIfOMSnSinkCurDaySuspectedFlag TruthValue,
jnxoptIfOMSnSinkCurDayLowAggregatedInputPower Integer32,
jnxoptIfOMSnSinkCurDayHighAggregatedInputPower Integer32,
jnxoptIfOMSnSinkCurDayLowOutputPower Integer32,
jnxoptIfOMSnSinkCurDayHighOutputPower Integer32
}
jnxoptIfOMSnSinkCurDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOMSnSinkCurDayEntry 1 }
jnxoptIfOMSnSinkCurDayLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power of all the DWDM input
channels during the current 24-hour interval."
::= { jnxoptIfOMSnSinkCurDayEntry 2 }
jnxoptIfOMSnSinkCurDayHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power of all the DWDM input
channels during the current 24-hour interval."
::= { jnxoptIfOMSnSinkCurDayEntry 3 }
jnxoptIfOMSnSinkCurDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power at the output
during the current 24-hour interval."
::= { jnxoptIfOMSnSinkCurDayEntry 4 }
jnxoptIfOMSnSinkCurDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power at the output
during the current 24-hour interval."
::= { jnxoptIfOMSnSinkCurDayEntry 5 }
-- OMSn sink previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.
jnxoptIfOMSnSinkPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnSinkPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OMSn sink performance monitoring information for
the previous 24-hour interval."
::= { jnxoptIfOMSn 5 }
jnxoptIfOMSnSinkPrevDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnSinkPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn sink performance
monitoring information of an interface for the previous
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOMSnSinkPrevDayTable 1 }
JnxoptIfOMSnSinkPrevDayEntry ::=
SEQUENCE {
jnxoptIfOMSnSinkPrevDaySuspectedFlag TruthValue,
jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower Integer32,
jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower Integer32,
jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower Integer32,
jnxoptIfOMSnSinkPrevDayLastOutputPower Integer32,
jnxoptIfOMSnSinkPrevDayLowOutputPower Integer32,
jnxoptIfOMSnSinkPrevDayHighOutputPower Integer32
}
jnxoptIfOMSnSinkPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOMSnSinkPrevDayEntry 1 }
jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last aggregated optical power of all the DWDM input
channels during the previous 24-hour interval."
::= { jnxoptIfOMSnSinkPrevDayEntry 2 }
jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power of all the DWDM input
channels during the previous 24-hour interval."
::= { jnxoptIfOMSnSinkPrevDayEntry 3 }
jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power of all the DWDM input
channels during the previous 24-hour interval."
::= { jnxoptIfOMSnSinkPrevDayEntry 4 }
jnxoptIfOMSnSinkPrevDayLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power at the output
during the previous 24-hour interval."
::= { jnxoptIfOMSnSinkPrevDayEntry 5 }
jnxoptIfOMSnSinkPrevDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power at the output
during the previous 24-hour interval."
::= { jnxoptIfOMSnSinkPrevDayEntry 6 }
jnxoptIfOMSnSinkPrevDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power at the output
during the previous 24-hour interval."
::= { jnxoptIfOMSnSinkPrevDayEntry 7 }
-- OMSn source current table
-- Contains data for the current 15-minute performance monitoring
-- interval.
jnxoptIfOMSnSrcCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnSrcCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OMSn source performance monitoring information for
the current 15-minute interval."
::= { jnxoptIfOMSn 6 }
jnxoptIfOMSnSrcCurrentEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnSrcCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn source performance
monitoring information of an interface for the current
15-minute interval."
INDEX { ifIndex }
::= { jnxoptIfOMSnSrcCurrentTable 1 }
JnxoptIfOMSnSrcCurrentEntry ::=
SEQUENCE {
jnxoptIfOMSnSrcCurrentSuspectedFlag TruthValue,
jnxoptIfOMSnSrcCurrentOutputPower Integer32,
jnxoptIfOMSnSrcCurrentLowOutputPower Integer32,
jnxoptIfOMSnSrcCurrentHighOutputPower Integer32,
jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold Integer32,
jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold Integer32,
jnxoptIfOMSnSrcCurrentAggregatedInputPower Integer32,
jnxoptIfOMSnSrcCurrentLowAggregatedInputPower Integer32,
jnxoptIfOMSnSrcCurrentHighAggregatedInputPower Integer32,
jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold Integer32,
jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold Integer32
}
jnxoptIfOMSnSrcCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOMSnSrcCurrentEntry 1 }
jnxoptIfOMSnSrcCurrentOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the output."
::= { jnxoptIfOMSnSrcCurrentEntry 2 }
jnxoptIfOMSnSrcCurrentLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOMSnSrcCurrentEntry 3 }
jnxoptIfOMSnSrcCurrentHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOMSnSrcCurrentEntry 4 }
jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on output power. If
jnxoptIfOMSnSrcCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOMSnSrcCurrentEntry 5 }
jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on output power. If
jnxoptIfOMSnSrcCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOMSnSrcCurrentEntry 6 }
jnxoptIfOMSnSrcCurrentAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The aggregated optical power at the input."
::= { jnxoptIfOMSnSrcCurrentEntry 7 }
jnxoptIfOMSnSrcCurrentLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power at the input
during the current 15-minute interval."
::= { jnxoptIfOMSnSrcCurrentEntry 8 }
jnxoptIfOMSnSrcCurrentHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power at the input
during the current 15-minute interval."
::= { jnxoptIfOMSnSrcCurrentEntry 9 }
jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on aggregated input power. If
jnxoptIfOMSnSrcCurrentAggregatedInputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOMSnSrcCurrentEntry 10 }
jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on aggregated input power. If
jnxoptIfOMSnSrcCurrentAggregatedInputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOMSnSrcCurrentEntry 11 }
-- OMSn source interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.
jnxoptIfOMSnSrcIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnSrcIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of historical OMSn source performance monitoring
information."
::= { jnxoptIfOMSn 7 }
jnxoptIfOMSnSrcIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnSrcIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn source performance
monitoring information of an interface during a particular
historical interval."
INDEX { ifIndex, jnxoptIfOMSnSrcIntervalNumber }
::= { jnxoptIfOMSnSrcIntervalTable 1 }
JnxoptIfOMSnSrcIntervalEntry ::=
SEQUENCE {
jnxoptIfOMSnSrcIntervalNumber JnxoptIfIntervalNumber,
jnxoptIfOMSnSrcIntervalSuspectedFlag TruthValue,
jnxoptIfOMSnSrcIntervalLastOutputPower Integer32,
jnxoptIfOMSnSrcIntervalLowOutputPower Integer32,
jnxoptIfOMSnSrcIntervalHighOutputPower Integer32,
jnxoptIfOMSnSrcIntervalLastAggregatedInputPower Integer32,
jnxoptIfOMSnSrcIntervalLowAggregatedInputPower Integer32,
jnxoptIfOMSnSrcIntervalHighAggregatedInputPower Integer32
}
jnxoptIfOMSnSrcIntervalNumber OBJECT-TYPE
SYNTAX JnxoptIfIntervalNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies the interval."
::= { jnxoptIfOMSnSrcIntervalEntry 1 }
jnxoptIfOMSnSrcIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOMSnSrcIntervalEntry 2 }
jnxoptIfOMSnSrcIntervalLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
interval."
::= { jnxoptIfOMSnSrcIntervalEntry 3 }
jnxoptIfOMSnSrcIntervalLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
interval."
::= { jnxoptIfOMSnSrcIntervalEntry 4 }
jnxoptIfOMSnSrcIntervalHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
interval."
::= { jnxoptIfOMSnSrcIntervalEntry 5 }
jnxoptIfOMSnSrcIntervalLastAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last aggregated optical power at the input
during the interval."
::= { jnxoptIfOMSnSrcIntervalEntry 6 }
jnxoptIfOMSnSrcIntervalLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power at the input
during the interval."
::= { jnxoptIfOMSnSrcIntervalEntry 7 }
jnxoptIfOMSnSrcIntervalHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power at the input
during the interval."
::= { jnxoptIfOMSnSrcIntervalEntry 8 }
-- OMSn source current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.
jnxoptIfOMSnSrcCurDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnSrcCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OMSn source performance monitoring information for
the current 24-hour interval."
::= { jnxoptIfOMSn 8 }
jnxoptIfOMSnSrcCurDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnSrcCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn source performance
monitoring information of an interface for the current
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOMSnSrcCurDayTable 1 }
JnxoptIfOMSnSrcCurDayEntry ::=
SEQUENCE {
jnxoptIfOMSnSrcCurDaySuspectedFlag TruthValue,
jnxoptIfOMSnSrcCurDayLowOutputPower Integer32,
jnxoptIfOMSnSrcCurDayHighOutputPower Integer32,
jnxoptIfOMSnSrcCurDayLowAggregatedInputPower Integer32,
jnxoptIfOMSnSrcCurDayHighAggregatedInputPower Integer32
}
jnxoptIfOMSnSrcCurDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOMSnSrcCurDayEntry 1 }
jnxoptIfOMSnSrcCurDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOMSnSrcCurDayEntry 2 }
jnxoptIfOMSnSrcCurDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOMSnSrcCurDayEntry 3 }
jnxoptIfOMSnSrcCurDayLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power at the input
during the current 24-hour interval."
::= { jnxoptIfOMSnSrcCurDayEntry 4 }
jnxoptIfOMSnSrcCurDayHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power at the input
during the current 24-hour interval."
::= { jnxoptIfOMSnSrcCurDayEntry 5 }
-- OMSn source previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.
jnxoptIfOMSnSrcPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOMSnSrcPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OMSn source performance monitoring information for
the previous 24-hour interval."
::= { jnxoptIfOMSn 9 }
jnxoptIfOMSnSrcPrevDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOMSnSrcPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OMSn source performance
monitoring information of an interface for the previous
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOMSnSrcPrevDayTable 1 }
JnxoptIfOMSnSrcPrevDayEntry ::=
SEQUENCE {
jnxoptIfOMSnSrcPrevDaySuspectedFlag TruthValue,
jnxoptIfOMSnSrcPrevDayLastOutputPower Integer32,
jnxoptIfOMSnSrcPrevDayLowOutputPower Integer32,
jnxoptIfOMSnSrcPrevDayHighOutputPower Integer32,
jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower Integer32,
jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower Integer32,
jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower Integer32
}
jnxoptIfOMSnSrcPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOMSnSrcPrevDayEntry 1 }
jnxoptIfOMSnSrcPrevDayLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOMSnSrcPrevDayEntry 2 }
jnxoptIfOMSnSrcPrevDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOMSnSrcPrevDayEntry 3 }
jnxoptIfOMSnSrcPrevDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOMSnSrcPrevDayEntry 4 }
jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last aggregated optical power at the input during the
previous 24-hour interval."
::= { jnxoptIfOMSnSrcPrevDayEntry 5 }
jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power at the input during the
previous 24-hour interval."
::= { jnxoptIfOMSnSrcPrevDayEntry 6 }
jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power at the input during the
previous 24-hour interval."
::= { jnxoptIfOMSnSrcPrevDayEntry 7 }
-- the jnxoptIfOChGroup group
-- This group handles the configuration and performance monitoring
-- information for OChGroup layers.
-- OChGroup config table
jnxoptIfOChGroupConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OChGroup configuration information."
::= { jnxoptIfOChGroup 1 }
jnxoptIfOChGroupConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup configuration
information of an interface."
INDEX { ifIndex }
::= { jnxoptIfOChGroupConfigTable 1 }
JnxoptIfOChGroupConfigEntry ::=
SEQUENCE {
jnxoptIfOChGroupDirectionality JnxoptIfDirectionality
}
jnxoptIfOChGroupDirectionality OBJECT-TYPE
SYNTAX JnxoptIfDirectionality
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the directionality of the entity."
::= { jnxoptIfOChGroupConfigEntry 1 }
-- OChGroup sink current table
-- Contains data for the current 15-minute performance monitoring
-- interval.
jnxoptIfOChGroupSinkCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupSinkCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OChGroup sink performance monitoring information for
the current 15-minute interval."
::= { jnxoptIfOChGroup 2 }
jnxoptIfOChGroupSinkCurrentEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupSinkCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup sink performance
monitoring information of an interface for the current
15-minute interval."
INDEX { ifIndex }
::= { jnxoptIfOChGroupSinkCurrentTable 1 }
JnxoptIfOChGroupSinkCurrentEntry ::=
SEQUENCE {
jnxoptIfOChGroupSinkCurrentSuspectedFlag TruthValue,
jnxoptIfOChGroupSinkCurrentAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold Integer32,
jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold Integer32,
jnxoptIfOChGroupSinkCurrentOutputPower Integer32,
jnxoptIfOChGroupSinkCurrentLowOutputPower Integer32,
jnxoptIfOChGroupSinkCurrentHighOutputPower Integer32,
jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold Integer32,
jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold Integer32
}
jnxoptIfOChGroupSinkCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChGroupSinkCurrentEntry 1 }
jnxoptIfOChGroupSinkCurrentAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The aggregated optical power of all the DWDM input
channels in the OChGroup."
::= { jnxoptIfOChGroupSinkCurrentEntry 2 }
jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power of all the DWDM input
channels in the OChGroup during the current 15-minute interval."
::= { jnxoptIfOChGroupSinkCurrentEntry 3 }
jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power of all the DWDM input
channels in the OChGroup during the current 15-minute interval."
::= { jnxoptIfOChGroupSinkCurrentEntry 4 }
jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on aggregated input power. If
jnxoptIfOChGroupSinkCurrentAggregatedInputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChGroupSinkCurrentEntry 5 }
jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on aggregated input power. If
jnxoptIfOChGroupSinkCurrentAggregatedInputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChGroupSinkCurrentEntry 6 }
jnxoptIfOChGroupSinkCurrentOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the output
in the OChGroup."
::= { jnxoptIfOChGroupSinkCurrentEntry 7 }
jnxoptIfOChGroupSinkCurrentLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output
in the OChGroup during the current 15-minute interval."
::= { jnxoptIfOChGroupSinkCurrentEntry 8 }
jnxoptIfOChGroupSinkCurrentHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output
in the OChGroup during the current 15-minute interval."
::= { jnxoptIfOChGroupSinkCurrentEntry 9 }
jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on the output power. If
jnxoptIfOChGroupSinkCurrentOutputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChGroupSinkCurrentEntry 10 }
jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on the output power. If
jnxoptIfOChGroupSinkCurrentOutputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChGroupSinkCurrentEntry 11 }
-- OChGroup sink interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.
jnxoptIfOChGroupSinkIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupSinkIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of historical OChGroup sink performance monitoring
information."
::= { jnxoptIfOChGroup 3 }
jnxoptIfOChGroupSinkIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupSinkIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup sink performance
monitoring information of an interface during a particular
historical interval."
INDEX { ifIndex, jnxoptIfOChGroupSinkIntervalNumber }
::= { jnxoptIfOChGroupSinkIntervalTable 1 }
JnxoptIfOChGroupSinkIntervalEntry ::=
SEQUENCE {
jnxoptIfOChGroupSinkIntervalNumber JnxoptIfIntervalNumber,
jnxoptIfOChGroupSinkIntervalSuspectedFlag TruthValue,
jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkIntervalLastOutputPower Integer32,
jnxoptIfOChGroupSinkIntervalLowOutputPower Integer32,
jnxoptIfOChGroupSinkIntervalHighOutputPower Integer32
}
jnxoptIfOChGroupSinkIntervalNumber OBJECT-TYPE
SYNTAX JnxoptIfIntervalNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies the interval."
::= { jnxoptIfOChGroupSinkIntervalEntry 1 }
jnxoptIfOChGroupSinkIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChGroupSinkIntervalEntry 2 }
jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last aggregated optical power of all the DWDM input
channels in the OChGroup during the interval."
::= { jnxoptIfOChGroupSinkIntervalEntry 3 }
jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power of all the DWDM input
channels in the OChGroup during the interval."
::= { jnxoptIfOChGroupSinkIntervalEntry 4 }
jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power of all the DWDM input
channels in the OChGroup during the interval."
::= { jnxoptIfOChGroupSinkIntervalEntry 5 }
jnxoptIfOChGroupSinkIntervalLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output
in the OChGroup during the interval."
::= { jnxoptIfOChGroupSinkIntervalEntry 6 }
jnxoptIfOChGroupSinkIntervalLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output
in the OChGroup during the interval."
::= { jnxoptIfOChGroupSinkIntervalEntry 7 }
jnxoptIfOChGroupSinkIntervalHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output
in the OChGroup during the interval."
::= { jnxoptIfOChGroupSinkIntervalEntry 8 }
-- OChGroup sink current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.
jnxoptIfOChGroupSinkCurDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupSinkCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OChGroup sink performance monitoring information for
the current 24-hour interval."
::= { jnxoptIfOChGroup 4 }
jnxoptIfOChGroupSinkCurDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupSinkCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup sink performance
monitoring information of an interface for the current
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOChGroupSinkCurDayTable 1 }
JnxoptIfOChGroupSinkCurDayEntry ::=
SEQUENCE {
jnxoptIfOChGroupSinkCurDaySuspectedFlag TruthValue,
jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkCurDayLowOutputPower Integer32,
jnxoptIfOChGroupSinkCurDayHighOutputPower Integer32
}
jnxoptIfOChGroupSinkCurDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChGroupSinkCurDayEntry 1 }
jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power of all the DWDM input
channels in the OChGroup during the current 24-hour interval."
::= { jnxoptIfOChGroupSinkCurDayEntry 2 }
jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power of all the DWDM input
channels in the OChGroup during the current 24-hour interval."
::= { jnxoptIfOChGroupSinkCurDayEntry 3 }
jnxoptIfOChGroupSinkCurDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output
in the OChGroup during the current 24-hour interval."
::= { jnxoptIfOChGroupSinkCurDayEntry 4 }
jnxoptIfOChGroupSinkCurDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output
in the OChGroup during the current 24-hour interval."
::= { jnxoptIfOChGroupSinkCurDayEntry 5 }
-- OChGroup sink previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.
jnxoptIfOChGroupSinkPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupSinkPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OChGroup sink performance monitoring information for
the previous 24-hour interval."
::= { jnxoptIfOChGroup 5 }
jnxoptIfOChGroupSinkPrevDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupSinkPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup sink performance
monitoring information of an interface for the previous
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOChGroupSinkPrevDayTable 1 }
JnxoptIfOChGroupSinkPrevDayEntry ::=
SEQUENCE {
jnxoptIfOChGroupSinkPrevDaySuspectedFlag TruthValue,
jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower Integer32,
jnxoptIfOChGroupSinkPrevDayLastOutputPower Integer32,
jnxoptIfOChGroupSinkPrevDayLowOutputPower Integer32,
jnxoptIfOChGroupSinkPrevDayHighOutputPower Integer32
}
jnxoptIfOChGroupSinkPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChGroupSinkPrevDayEntry 1 }
jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last aggregated optical power of all the DWDM input
channels in the OChGroup during the previous 24-hour interval."
::= { jnxoptIfOChGroupSinkPrevDayEntry 2 }
jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power of all the DWDM input
channels in the OChGroup during the previous 24-hour interval."
::= { jnxoptIfOChGroupSinkPrevDayEntry 3 }
jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power of all the DWDM input
channels in the OChGroup during the previous 24-hour interval."
::= { jnxoptIfOChGroupSinkPrevDayEntry 4 }
jnxoptIfOChGroupSinkPrevDayLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output
in the OChGroup during the previous 24-hour interval."
::= { jnxoptIfOChGroupSinkPrevDayEntry 5 }
jnxoptIfOChGroupSinkPrevDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output
in the OChGroup during the previous 24-hour interval."
::= { jnxoptIfOChGroupSinkPrevDayEntry 6 }
jnxoptIfOChGroupSinkPrevDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output
in the OChGroup during the previous 24-hour interval."
::= { jnxoptIfOChGroupSinkPrevDayEntry 7 }
-- OChGroup source current table
-- Contains data for the current 15-minute performance monitoring
-- interval.
jnxoptIfOChGroupSrcCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupSrcCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OChGroup source performance monitoring information for
the current 15-minute interval."
::= { jnxoptIfOChGroup 6 }
jnxoptIfOChGroupSrcCurrentEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupSrcCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup source performance
monitoring information of an interface for the current
15-minute interval."
INDEX { ifIndex }
::= { jnxoptIfOChGroupSrcCurrentTable 1 }
JnxoptIfOChGroupSrcCurrentEntry ::=
SEQUENCE {
jnxoptIfOChGroupSrcCurrentSuspectedFlag TruthValue,
jnxoptIfOChGroupSrcCurrentOutputPower Integer32,
jnxoptIfOChGroupSrcCurrentLowOutputPower Integer32,
jnxoptIfOChGroupSrcCurrentHighOutputPower Integer32,
jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold Integer32,
jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold Integer32,
jnxoptIfOChGroupSrcCurrentAggregatedInputPower Integer32,
jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower Integer32,
jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower Integer32,
jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold Integer32,
jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold Integer32
}
jnxoptIfOChGroupSrcCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChGroupSrcCurrentEntry 1 }
jnxoptIfOChGroupSrcCurrentOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the output."
::= { jnxoptIfOChGroupSrcCurrentEntry 2 }
jnxoptIfOChGroupSrcCurrentLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOChGroupSrcCurrentEntry 3 }
jnxoptIfOChGroupSrcCurrentHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOChGroupSrcCurrentEntry 4 }
jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on output power. If
jnxoptIfOChGroupSrcCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChGroupSrcCurrentEntry 5 }
jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on output power. If
jnxoptIfOChGroupSrcCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChGroupSrcCurrentEntry 6 }
jnxoptIfOChGroupSrcCurrentAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The aggregated optical power monitored at the input."
::= { jnxoptIfOChGroupSrcCurrentEntry 7 }
jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power monitored at the input
during the current 15-minute interval."
::= { jnxoptIfOChGroupSrcCurrentEntry 8 }
jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power monitored at the input
during the current 15-minute interval."
::= { jnxoptIfOChGroupSrcCurrentEntry 9 }
jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on input power. If
jnxoptIfOChGroupSrcCurrentAggregatedInputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChGroupSrcCurrentEntry 10 }
jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on input power. If
jnxoptIfOChGroupSrcCurrentAggregatedInputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChGroupSrcCurrentEntry 11 }
-- OChGroup source interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.
jnxoptIfOChGroupSrcIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupSrcIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of historical OChGroup source performance monitoring
information."
::= { jnxoptIfOChGroup 7 }
jnxoptIfOChGroupSrcIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupSrcIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup source performance
monitoring information of an interface during a particular
historical interval."
INDEX { ifIndex, jnxoptIfOChGroupSrcIntervalNumber }
::= { jnxoptIfOChGroupSrcIntervalTable 1 }
JnxoptIfOChGroupSrcIntervalEntry ::=
SEQUENCE {
jnxoptIfOChGroupSrcIntervalNumber JnxoptIfIntervalNumber,
jnxoptIfOChGroupSrcIntervalSuspectedFlag TruthValue,
jnxoptIfOChGroupSrcIntervalLastOutputPower Integer32,
jnxoptIfOChGroupSrcIntervalLowOutputPower Integer32,
jnxoptIfOChGroupSrcIntervalHighOutputPower Integer32,
jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower Integer32,
jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower Integer32,
jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower Integer32
}
jnxoptIfOChGroupSrcIntervalNumber OBJECT-TYPE
SYNTAX JnxoptIfIntervalNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies the interval."
::= { jnxoptIfOChGroupSrcIntervalEntry 1 }
jnxoptIfOChGroupSrcIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChGroupSrcIntervalEntry 2 }
jnxoptIfOChGroupSrcIntervalLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
interval."
::= { jnxoptIfOChGroupSrcIntervalEntry 3 }
jnxoptIfOChGroupSrcIntervalLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
interval."
::= { jnxoptIfOChGroupSrcIntervalEntry 4 }
jnxoptIfOChGroupSrcIntervalHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
interval."
::= { jnxoptIfOChGroupSrcIntervalEntry 5 }
jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last aggregated optical power monitored at the input
during the interval."
::= { jnxoptIfOChGroupSrcIntervalEntry 6 }
jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power monitored at the input
during the interval."
::= { jnxoptIfOChGroupSrcIntervalEntry 7 }
jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power monitored at the input
during the interval."
::= { jnxoptIfOChGroupSrcIntervalEntry 8 }
-- OChGroup source current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.
jnxoptIfOChGroupSrcCurDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupSrcCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OChGroup source performance monitoring information for
the current 24-hour interval."
::= { jnxoptIfOChGroup 8 }
jnxoptIfOChGroupSrcCurDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupSrcCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup source performance
monitoring information of an interface for the current
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOChGroupSrcCurDayTable 1 }
JnxoptIfOChGroupSrcCurDayEntry ::=
SEQUENCE {
jnxoptIfOChGroupSrcCurDaySuspectedFlag TruthValue,
jnxoptIfOChGroupSrcCurDayLowOutputPower Integer32,
jnxoptIfOChGroupSrcCurDayHighOutputPower Integer32,
jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower Integer32,
jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower Integer32
}
jnxoptIfOChGroupSrcCurDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChGroupSrcCurDayEntry 1 }
jnxoptIfOChGroupSrcCurDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOChGroupSrcCurDayEntry 2 }
jnxoptIfOChGroupSrcCurDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOChGroupSrcCurDayEntry 3 }
jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power monitored at the input
during the current 24-hour interval."
::= { jnxoptIfOChGroupSrcCurDayEntry 4 }
jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power monitored at the input
during the current 24-hour interval."
::= { jnxoptIfOChGroupSrcCurDayEntry 5 }
-- OChGroup source previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.
jnxoptIfOChGroupSrcPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChGroupSrcPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OChGroup source performance monitoring information for
the previous 24-hour interval."
::= { jnxoptIfOChGroup 9 }
jnxoptIfOChGroupSrcPrevDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOChGroupSrcPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OChGroup source performance
monitoring information of an interface for the previous
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOChGroupSrcPrevDayTable 1 }
JnxoptIfOChGroupSrcPrevDayEntry ::=
SEQUENCE {
jnxoptIfOChGroupSrcPrevDaySuspectedFlag TruthValue,
jnxoptIfOChGroupSrcPrevDayLastOutputPower Integer32,
jnxoptIfOChGroupSrcPrevDayLowOutputPower Integer32,
jnxoptIfOChGroupSrcPrevDayHighOutputPower Integer32,
jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower Integer32,
jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower Integer32,
jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower Integer32
}
jnxoptIfOChGroupSrcPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChGroupSrcPrevDayEntry 1 }
jnxoptIfOChGroupSrcPrevDayLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOChGroupSrcPrevDayEntry 2 }
jnxoptIfOChGroupSrcPrevDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOChGroupSrcPrevDayEntry 3 }
jnxoptIfOChGroupSrcPrevDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOChGroupSrcPrevDayEntry 4 }
jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last aggregated optical power monitored at the input
during the previous 24-hour interval."
::= { jnxoptIfOChGroupSrcPrevDayEntry 5 }
jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest aggregated optical power monitored at the input
during the previous 24-hour interval."
::= { jnxoptIfOChGroupSrcPrevDayEntry 6 }
jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest aggregated optical power monitored at the input
during the previous 24-hour interval."
::= { jnxoptIfOChGroupSrcPrevDayEntry 7 }
-- the jnxoptIfOCh group
-- This group handles the configuration and
-- performance monitoring information for OCh layers.
-- OCh config table
jnxoptIfOChConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh configuration information."
::= { jnxoptIfOCh 1 }
jnxoptIfOChConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfOChConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh configuration
information of an interface."
INDEX { ifIndex }
::= { jnxoptIfOChConfigTable 1 }
JnxoptIfOChConfigEntry ::=
SEQUENCE {
jnxoptIfOChDirectionality JnxoptIfDirectionality,
jnxoptIfOChCurrentStatus BITS
}
jnxoptIfOChDirectionality OBJECT-TYPE
SYNTAX JnxoptIfDirectionality
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the directionality of the entity."
::= { jnxoptIfOChConfigEntry 1 }
jnxoptIfOChCurrentStatus OBJECT-TYPE
SYNTAX BITS {
losP(0),
los(1),
oci(2),
ssfP(3),
ssfO(4),
ssf(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the defect condition of the entity, if any.
This object is applicable when jnxoptIfOChDirectionality
has the value sink(1) or bidirectional(3).
In full-capability systems the bit position los(1) is not used.
In reduced-capability systems or at IrDI interfaces only
the bit positions los(1) and ssfP(3) are used."
::= { jnxoptIfOChConfigEntry 2 }
-- OCh sink current table
-- Contains data for the current 15-minute performance monitoring
-- interval.
jnxoptIfOChSinkCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChSinkCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh sink performance monitoring information for
the current 15-minute interval."
::= { jnxoptIfOCh 2 }
jnxoptIfOChSinkCurrentEntry OBJECT-TYPE
SYNTAX JnxoptIfOChSinkCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh sink performance
monitoring information for an interface for the current
15-minute interval."
INDEX { ifIndex }
::= { jnxoptIfOChSinkCurrentTable 1 }
JnxoptIfOChSinkCurrentEntry ::=
SEQUENCE {
jnxoptIfOChSinkCurrentSuspectedFlag TruthValue,
jnxoptIfOChSinkCurrentInputPower Integer32,
jnxoptIfOChSinkCurrentLowInputPower Integer32,
jnxoptIfOChSinkCurrentHighInputPower Integer32,
jnxoptIfOChSinkCurrentLowerInputPowerThreshold Integer32,
jnxoptIfOChSinkCurrentUpperInputPowerThreshold Integer32
}
jnxoptIfOChSinkCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChSinkCurrentEntry 1 }
jnxoptIfOChSinkCurrentInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the input."
::= { jnxoptIfOChSinkCurrentEntry 2 }
jnxoptIfOChSinkCurrentLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
current 15-minute interval."
::= { jnxoptIfOChSinkCurrentEntry 3 }
jnxoptIfOChSinkCurrentHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
current 15-minute interval."
::= { jnxoptIfOChSinkCurrentEntry 4 }
jnxoptIfOChSinkCurrentLowerInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on input power. If
jnxoptIfOChSinkCurrentInputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChSinkCurrentEntry 5 }
jnxoptIfOChSinkCurrentUpperInputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on input power. If
jnxoptIfOChSinkCurrentInputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChSinkCurrentEntry 6 }
-- OCh sink interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.
jnxoptIfOChSinkIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChSinkIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of historical OCh sink performance monitoring
information."
::= { jnxoptIfOCh 3 }
jnxoptIfOChSinkIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfOChSinkIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh sink performance
monitoring information of an interface during a particular
historical interval."
INDEX { ifIndex, jnxoptIfOChSinkIntervalNumber }
::= { jnxoptIfOChSinkIntervalTable 1 }
JnxoptIfOChSinkIntervalEntry ::=
SEQUENCE {
jnxoptIfOChSinkIntervalNumber JnxoptIfIntervalNumber,
jnxoptIfOChSinkIntervalSuspectedFlag TruthValue,
jnxoptIfOChSinkIntervalLastInputPower Integer32,
jnxoptIfOChSinkIntervalLowInputPower Integer32,
jnxoptIfOChSinkIntervalHighInputPower Integer32
}
jnxoptIfOChSinkIntervalNumber OBJECT-TYPE
SYNTAX JnxoptIfIntervalNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies the interval."
::= { jnxoptIfOChSinkIntervalEntry 1 }
jnxoptIfOChSinkIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChSinkIntervalEntry 2 }
jnxoptIfOChSinkIntervalLastInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the input during the
interval."
::= { jnxoptIfOChSinkIntervalEntry 3 }
jnxoptIfOChSinkIntervalLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
interval."
::= { jnxoptIfOChSinkIntervalEntry 4 }
jnxoptIfOChSinkIntervalHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
interval."
::= { jnxoptIfOChSinkIntervalEntry 5 }
-- OCh sink current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.
jnxoptIfOChSinkCurDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChSinkCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh sink performance monitoring information for
the current 24-hour interval."
::= { jnxoptIfOCh 4 }
jnxoptIfOChSinkCurDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOChSinkCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh sink performance
monitoring information of an interface for the current
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOChSinkCurDayTable 1 }
JnxoptIfOChSinkCurDayEntry ::=
SEQUENCE {
jnxoptIfOChSinkCurDaySuspectedFlag TruthValue,
jnxoptIfOChSinkCurDayLowInputPower Integer32,
jnxoptIfOChSinkCurDayHighInputPower Integer32
}
jnxoptIfOChSinkCurDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChSinkCurDayEntry 1 }
jnxoptIfOChSinkCurDayLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
current 24-hour interval."
::= { jnxoptIfOChSinkCurDayEntry 2 }
jnxoptIfOChSinkCurDayHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
current 24-hour interval."
::= { jnxoptIfOChSinkCurDayEntry 3 }
-- OCh sink previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.
jnxoptIfOChSinkPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChSinkPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh sink performance monitoring information for
the previous 24-hour interval."
::= { jnxoptIfOCh 5 }
jnxoptIfOChSinkPrevDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOChSinkPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh sink performance
monitoring information of an interface for the previous
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOChSinkPrevDayTable 1 }
JnxoptIfOChSinkPrevDayEntry ::=
SEQUENCE {
jnxoptIfOChSinkPrevDaySuspectedFlag TruthValue,
jnxoptIfOChSinkPrevDayLastInputPower Integer32,
jnxoptIfOChSinkPrevDayLowInputPower Integer32,
jnxoptIfOChSinkPrevDayHighInputPower Integer32
}
jnxoptIfOChSinkPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChSinkPrevDayEntry 1 }
jnxoptIfOChSinkPrevDayLastInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOChSinkPrevDayEntry 2 }
jnxoptIfOChSinkPrevDayLowInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOChSinkPrevDayEntry 3 }
jnxoptIfOChSinkPrevDayHighInputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the input during the
previous 24-hour interval."
::= { jnxoptIfOChSinkPrevDayEntry 4 }
-- OCh source current table
-- Contains data for the current 15-minute performance monitoring
-- interval.
jnxoptIfOChSrcCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChSrcCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh source performance monitoring information for
the current 15-minute interval."
::= { jnxoptIfOCh 6 }
jnxoptIfOChSrcCurrentEntry OBJECT-TYPE
SYNTAX JnxoptIfOChSrcCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh source performance
monitoring information of an interface for the current
15-minute interval."
INDEX { ifIndex }
::= { jnxoptIfOChSrcCurrentTable 1 }
JnxoptIfOChSrcCurrentEntry ::=
SEQUENCE {
jnxoptIfOChSrcCurrentSuspectedFlag TruthValue,
jnxoptIfOChSrcCurrentOutputPower Integer32,
jnxoptIfOChSrcCurrentLowOutputPower Integer32,
jnxoptIfOChSrcCurrentHighOutputPower Integer32,
jnxoptIfOChSrcCurrentLowerOutputPowerThreshold Integer32,
jnxoptIfOChSrcCurrentUpperOutputPowerThreshold Integer32
}
jnxoptIfOChSrcCurrentSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChSrcCurrentEntry 1 }
jnxoptIfOChSrcCurrentOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The optical power monitored at the output."
::= { jnxoptIfOChSrcCurrentEntry 2 }
jnxoptIfOChSrcCurrentLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOChSrcCurrentEntry 3 }
jnxoptIfOChSrcCurrentHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 15-minute interval."
::= { jnxoptIfOChSrcCurrentEntry 4 }
jnxoptIfOChSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The lower limit threshold on output power. If
jnxoptIfOChSrcCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChSrcCurrentEntry 5 }
jnxoptIfOChSrcCurrentUpperOutputPowerThreshold OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper limit threshold on output power. If
jnxoptIfOChSrcCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."
::= { jnxoptIfOChSrcCurrentEntry 6 }
-- OCh source interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.
jnxoptIfOChSrcIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChSrcIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of historical OCh source performance monitoring
information."
::= { jnxoptIfOCh 7 }
jnxoptIfOChSrcIntervalEntry OBJECT-TYPE
SYNTAX JnxoptIfOChSrcIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh source performance
monitoring information of an interface during a particular
historical interval."
INDEX { ifIndex, jnxoptIfOChSrcIntervalNumber }
::= { jnxoptIfOChSrcIntervalTable 1 }
JnxoptIfOChSrcIntervalEntry ::=
SEQUENCE {
jnxoptIfOChSrcIntervalNumber JnxoptIfIntervalNumber,
jnxoptIfOChSrcIntervalSuspectedFlag TruthValue,
jnxoptIfOChSrcIntervalLastOutputPower Integer32,
jnxoptIfOChSrcIntervalLowOutputPower Integer32,
jnxoptIfOChSrcIntervalHighOutputPower Integer32
}
jnxoptIfOChSrcIntervalNumber OBJECT-TYPE
SYNTAX JnxoptIfIntervalNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Uniquely identifies the interval."
::= { jnxoptIfOChSrcIntervalEntry 1 }
jnxoptIfOChSrcIntervalSuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChSrcIntervalEntry 2 }
jnxoptIfOChSrcIntervalLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
interval."
::= { jnxoptIfOChSrcIntervalEntry 3 }
jnxoptIfOChSrcIntervalLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
interval."
::= { jnxoptIfOChSrcIntervalEntry 4 }
jnxoptIfOChSrcIntervalHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
interval."
::= { jnxoptIfOChSrcIntervalEntry 5 }
-- OCh source current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.
jnxoptIfOChSrcCurDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChSrcCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh source performance monitoring information for
the current 24-hour interval."
::= { jnxoptIfOCh 8 }
jnxoptIfOChSrcCurDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOChSrcCurDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh source performance
monitoring information of an interface for the current
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOChSrcCurDayTable 1 }
JnxoptIfOChSrcCurDayEntry ::=
SEQUENCE {
jnxoptIfOChSrcCurDaySuspectedFlag TruthValue,
jnxoptIfOChSrcCurDayLowOutputPower Integer32,
jnxoptIfOChSrcCurDayHighOutputPower Integer32
}
jnxoptIfOChSrcCurDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChSrcCurDayEntry 1 }
jnxoptIfOChSrcCurDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOChSrcCurDayEntry 2 }
jnxoptIfOChSrcCurDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
current 24-hour interval."
::= { jnxoptIfOChSrcCurDayEntry 3 }
-- OCh source previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.
jnxoptIfOChSrcPrevDayTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOChSrcPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OCh source performance monitoring information for
the previous 24-hour interval."
::= { jnxoptIfOCh 9 }
jnxoptIfOChSrcPrevDayEntry OBJECT-TYPE
SYNTAX JnxoptIfOChSrcPrevDayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OCh source performance
monitoring information of an interface for the previous
24-hour interval."
INDEX { ifIndex }
::= { jnxoptIfOChSrcPrevDayTable 1 }
JnxoptIfOChSrcPrevDayEntry ::=
SEQUENCE {
jnxoptIfOChSrcPrevDaySuspectedFlag TruthValue,
jnxoptIfOChSrcPrevDayLastOutputPower Integer32,
jnxoptIfOChSrcPrevDayLowOutputPower Integer32,
jnxoptIfOChSrcPrevDayHighOutputPower Integer32
}
jnxoptIfOChSrcPrevDaySuspectedFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true, the data in this entry may be unreliable."
::= { jnxoptIfOChSrcPrevDayEntry 1 }
jnxoptIfOChSrcPrevDayLastOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOChSrcPrevDayEntry 2 }
jnxoptIfOChSrcPrevDayLowOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lowest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOChSrcPrevDayEntry 3 }
jnxoptIfOChSrcPrevDayHighOutputPower OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dbm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest optical power monitored at the output during the
previous 24-hour interval."
::= { jnxoptIfOChSrcPrevDayEntry 4 }
-- the jnxoptIfOTUk group
-- This group handles the configuration
-- information for OTUk layers.
-- OTUk config table
jnxoptIfOTUkConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfOTUkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of OTUk configuration information."
::= { jnxoptIfOTUk 1 }
jnxoptIfOTUkConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfOTUkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains OTUk configuration
information of an interface."
INDEX { ifIndex }
::= { jnxoptIfOTUkConfigTable 1 }
JnxoptIfOTUkConfigEntry ::=
SEQUENCE {
jnxoptIfOTUkDirectionality JnxoptIfDirectionality,
jnxoptIfOTUkBitRateK JnxoptIfBitRateK,
jnxoptIfOTUkTraceIdentifierTransmitted JnxoptIfTxTI,
jnxoptIfOTUkDAPIExpected JnxoptIfExDAPI,
jnxoptIfOTUkSAPIExpected JnxoptIfExSAPI,
jnxoptIfOTUkTraceIdentifierAccepted JnxoptIfAcTI,
jnxoptIfOTUkTIMDetMode JnxoptIfTIMDetMode,
jnxoptIfOTUkTIMActEnabled TruthValue,
jnxoptIfOTUkDEGThr JnxoptIfDEGThr,
jnxoptIfOTUkDEGM JnxoptIfDEGM,
jnxoptIfOTUkSinkAdaptActive TruthValue,
jnxoptIfOTUkSourceAdaptActive TruthValue,
jnxoptIfOTUkSinkFECEnabled TruthValue,
jnxoptIfOTUkCurrentStatus BITS
}
jnxoptIfOTUkDirectionality OBJECT-TYPE
SYNTAX JnxoptIfDirectionality
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the directionality of the entity."
::= { jnxoptIfOTUkConfigEntry 1 }
jnxoptIfOTUkBitRateK OBJECT-TYPE
SYNTAX JnxoptIfBitRateK
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the bit rate of the entity."
::= { jnxoptIfOTUkConfigEntry 2 }
jnxoptIfOTUkTraceIdentifierTransmitted OBJECT-TYPE
SYNTAX JnxoptIfTxTI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The trace identifier transmitted.
This object is applicable when jnxoptIfOTUkDirectionality
has the value source(2) or bidirectional(3). It must not
be instantiated in rows where jnxoptIfOTUkDirectionality
has the value sink(1).
If no value is ever set by a management entity for this
object, system-specific default value will be used.
Any implementation that instantiates this object must
document the system-specific default value or how it
is derived."
::= { jnxoptIfOTUkConfigEntry 3 }
jnxoptIfOTUkDAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExDAPI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
This object has no effect when jnxoptIfOTUkTIMDetMode has
the value off(1)."
::= { jnxoptIfOTUkConfigEntry 4 }
jnxoptIfOTUkSAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExSAPI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The SAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
This object has no effect when jnxoptIfOTUkTIMDetMode has
the value off(1)."
::= { jnxoptIfOTUkConfigEntry 5 }
jnxoptIfOTUkTraceIdentifierAccepted OBJECT-TYPE
SYNTAX JnxoptIfAcTI
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual trace identifier accepted.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
The value of this object is unspecified when
jnxoptIfOTUkCurrentStatus indicates a near-end defect
(i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents
extraction of the trace message."
::= { jnxoptIfOTUkConfigEntry 6 }
jnxoptIfOTUkTIMDetMode OBJECT-TYPE
SYNTAX JnxoptIfTIMDetMode
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
The default value of this object is off(1)."
::= { jnxoptIfOTUkConfigEntry 7 }
jnxoptIfOTUkTIMActEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
This object has no effect when jnxoptIfOTUkTIMDetMode has
the value off(1).
The default value of this object is false(2)."
::= { jnxoptIfOTUkConfigEntry 8 }
jnxoptIfOTUkDEGThr OBJECT-TYPE
SYNTAX JnxoptIfDEGThr
UNITS "percentage"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to jnxoptIfOTUkDEGThr.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
The default value of this object is Severely Errored Second
(SES) Estimator (See ITU-T G.7710)."
::= { jnxoptIfOTUkConfigEntry 9 }
jnxoptIfOTUkDEGM OBJECT-TYPE
SYNTAX JnxoptIfDEGM
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if jnxoptIfOTUkDEGM
consecutive bad PM Seconds are detected.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
The default value of this object is 7 (See ITU-T G.7710)."
::= { jnxoptIfOTUkConfigEntry 10 }
jnxoptIfOTUkSinkAdaptActive OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the sink adaptation function is activated or
not.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
The default value of this object is false(2)."
::= { jnxoptIfOTUkConfigEntry 11 }
jnxoptIfOTUkSourceAdaptActive OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the source adaptation function is activated or
not.
This object is only applicable to the source function, i.e.,
only when jnxoptIfOTUkDirectionality has the value source(2)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value sink(1).
The default value of this object is false(2)."
::= { jnxoptIfOTUkConfigEntry 12 }
jnxoptIfOTUkSinkFECEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If Forward Error Correction (FEC) is supported, this object
indicates whether FEC at the OTUk sink adaptation function is
enabled or not.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2).
The default value of this object is true(1)."
::= { jnxoptIfOTUkConfigEntry 13 }
jnxoptIfOTUkCurrentStatus OBJECT-TYPE
SYNTAX BITS {
tim(0),
deg(1),
bdi(2),
ssf(3),
lof(4),
ais(5),
lom(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the defect condition of the entity, if any.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfOTUkDirectionality has the value source(2)."
::= { jnxoptIfOTUkConfigEntry 14 }
-- GCC0 config table
jnxoptIfGCC0ConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfGCC0ConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of GCC0 configuration information."
::= { jnxoptIfOTUk 2 }
jnxoptIfGCC0ConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfGCC0ConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains GCC0 configuration
information of an interface. Each instance must
correspond to an instance of jnxoptIfOTUkConfigEntry.
Separate source and/or sink instances may exist
for a given ifIndex value, or a single bidirectional
instance may exist, but a bidirectional instance may
not coexist with a source or sink instance.
Instances of this conceptual row persist across
agent restarts."
INDEX { ifIndex, jnxoptIfGCC0Directionality }
::= { jnxoptIfGCC0ConfigTable 1 }
JnxoptIfGCC0ConfigEntry ::=
SEQUENCE {
jnxoptIfGCC0Directionality JnxoptIfDirectionality,
jnxoptIfGCC0Application SnmpAdminString,
jnxoptIfGCC0RowStatus RowStatus
}
jnxoptIfGCC0Directionality OBJECT-TYPE
SYNTAX JnxoptIfDirectionality
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the directionality of the entity.
The values source(2) and bidirectional(3) are
not allowed if the corresponding instance of
jnxoptIfOTUkDirectionality has the value sink(1).
The values sink(1) and bidirectional(3) are
not allowed if the corresponding instance of
jnxoptIfOTUkDirectionality has the value source(2)."
::= { jnxoptIfGCC0ConfigEntry 1 }
jnxoptIfGCC0Application OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the application transported by the GCC0 entity.
Example applications are ECC, User data channel.
The value of this object may not be changed when
jnxoptIfGCC0RowStatus has the value active(1)."
::= { jnxoptIfGCC0ConfigEntry 2 }
jnxoptIfGCC0RowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This columnar object is used for creating and deleting a
conceptual row of the jnxoptIfGCC0 config table.
It is used to model the addGCC0Access and removeGCC0Access
operations of an OTUk_TTP for GCC0 access control as defined
in G.874.1. Setting RowStatus to createAndGo or createAndWait
implies addGCC0Access. Setting RowStatus to destroy implies
removeGCC0Access."
::= { jnxoptIfGCC0ConfigEntry 3 }
-- the jnxoptIfODUk group
-- This group handles the configuration information
-- for the ODUk layers.
-- ODUk config table
jnxoptIfODUkConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfODUkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of ODUk configuration information."
::= { jnxoptIfODUk 1 }
jnxoptIfODUkConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfODUkConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains ODUk configuration
information of an interface."
INDEX { ifIndex }
::= { jnxoptIfODUkConfigTable 1 }
JnxoptIfODUkConfigEntry ::=
SEQUENCE {
jnxoptIfODUkDirectionality JnxoptIfDirectionality,
jnxoptIfODUkBitRateK JnxoptIfBitRateK,
jnxoptIfODUkTcmFieldsInUse BITS,
jnxoptIfODUkPositionSeqCurrentSize Unsigned32,
jnxoptIfODUkTtpPresent TruthValue
}
jnxoptIfODUkDirectionality OBJECT-TYPE
SYNTAX JnxoptIfDirectionality
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the directionality of the entity."
::= { jnxoptIfODUkConfigEntry 1 }
jnxoptIfODUkBitRateK OBJECT-TYPE
SYNTAX JnxoptIfBitRateK
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the bit rate of the entity."
::= { jnxoptIfODUkConfigEntry 2 }
jnxoptIfODUkTcmFieldsInUse OBJECT-TYPE
SYNTAX BITS {
tcmField1(0),
tcmField2(1),
tcmField3(2),
tcmField4(3),
tcmField5(4),
tcmField6(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the TCM field(s) that are currently in use.
The positions of the bits correspond to the TCM fields.
A bit that is set to 1 means that the corresponding TCM
field is used. This object will be updated when rows are
created in or deleted from the jnxoptIfODUkTConfigTable, or
the jnxoptIfODUkTNimConfigTable."
::= { jnxoptIfODUkConfigEntry 3 }
jnxoptIfODUkPositionSeqCurrentSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the current size of the position
sequence (i.e., number of TCM function and/or GCC12
access that have been created in the ODUk interface).
When the value of this variable is greater than zero,
it means that one or more TCM function and/or GCC12
access have been created in the ODUk interface. In this
case, there will be as many rows in the
jnxoptIfODUkPositionSeqTable as the value of
jnxoptIfODUkPositionSeqCurrentSize corresponding to this
ODUk interface, one row for each TCM function or GCC12
access. The position of the TCM function and/or
GCC12 access within the sequence is indicated by the
jnxoptIfODUkPositionSeqPosition variable in
jnxoptIfODUkPositionSeqTable.
The jnxoptIfODUkPositionSeqTable also provides pointers
to the corresponding TCM function (jnxoptIfODUkT) and
GCC12 access (jnxoptIfGCC12) entities."
::= { jnxoptIfODUkConfigEntry 4 }
jnxoptIfODUkTtpPresent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object has the value true(1) if the ifEntry under which
it is instantiated contains an ODUk Trail Termination Point,
i.e., is the endpoint of an ODUk path. In that case there
will be a corresponding row in the ODUk TTP config table and
it will not be possible to create corresponding rows in the
ODUk NIM config table. This object has the value false(2)
if the ifEntry under which it is instantiated contains an
intermediate ODUk Connection Termination Point. In that case
there is no corresponding row in the ODUk TTP config table,
but it will be possible to create corresponding rows in the
ODUk NIM config table. This object also affects the allowable
options in rows created in the GCC12 config table and in the
ODUkT config table, as specified in the DESCRIPTION clauses
of the columns in those tables."
::= { jnxoptIfODUkConfigEntry 5 }
-- ODUk Trail Termination Point (TTP) config table
jnxoptIfODUkTtpConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfODUkTtpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of ODUk TTP configuration information."
::= { jnxoptIfODUk 2 }
jnxoptIfODUkTtpConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfODUkTtpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains ODUk TTP configuration
information of an interface."
INDEX { ifIndex }
::= { jnxoptIfODUkTtpConfigTable 1 }
JnxoptIfODUkTtpConfigEntry ::=
SEQUENCE {
jnxoptIfODUkTtpTraceIdentifierTransmitted JnxoptIfTxTI,
jnxoptIfODUkTtpDAPIExpected JnxoptIfExDAPI,
jnxoptIfODUkTtpSAPIExpected JnxoptIfExSAPI,
jnxoptIfODUkTtpTraceIdentifierAccepted JnxoptIfAcTI,
jnxoptIfODUkTtpTIMDetMode JnxoptIfTIMDetMode,
jnxoptIfODUkTtpTIMActEnabled TruthValue,
jnxoptIfODUkTtpDEGThr JnxoptIfDEGThr,
jnxoptIfODUkTtpDEGM JnxoptIfDEGM,
jnxoptIfODUkTtpCurrentStatus BITS
}
jnxoptIfODUkTtpTraceIdentifierTransmitted OBJECT-TYPE
SYNTAX JnxoptIfTxTI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The trace identifier transmitted.
This object is applicable when jnxoptIfODUkDirectionality
has the value source(2) or bidirectional(3). It must not
be instantiated in rows where jnxoptIfODUkDirectionality
has the value sink(1).
If no value is ever set by a management entity for this
object, system-specific default value will be used.
Any implementation that instantiates this object must
document the system-specific default value or how it
is derived."
::= { jnxoptIfODUkTtpConfigEntry 1 }
jnxoptIfODUkTtpDAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExDAPI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfODUkDirectionality has the value source(2).
This object has no effect when jnxoptIfODUkTtpTIMDetMode has
the value off(1)."
::= { jnxoptIfODUkTtpConfigEntry 2 }
jnxoptIfODUkTtpSAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExSAPI
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The SAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfODUkDirectionality has the value source(2).
This object has no effect when jnxoptIfODUkTtpTIMDetMode has
the value off(1)."
::= { jnxoptIfODUkTtpConfigEntry 3 }
jnxoptIfODUkTtpTraceIdentifierAccepted OBJECT-TYPE
SYNTAX JnxoptIfAcTI
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual trace identifier accepted.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfODUkDirectionality has the value source(2).
The value of this object is unspecified when
jnxoptIfODUkTtpCurrentStatus indicates a near-end defect
(i.e., oci(0), lck(1), ssf(5)) that prevents extraction
of the trace message."
::= { jnxoptIfODUkTtpConfigEntry 4 }
jnxoptIfODUkTtpTIMDetMode OBJECT-TYPE
SYNTAX JnxoptIfTIMDetMode
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfODUkDirectionality has the value source(2).
The default value of this object is off(1)."
::= { jnxoptIfODUkTtpConfigEntry 5 }
jnxoptIfODUkTtpTIMActEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfODUkDirectionality has the value source(2).
This object has no effect when jnxoptIfODUkTtpTIMDetMode has
the value off(1).
The default value of this object is false(2)."
::= { jnxoptIfODUkTtpConfigEntry 6 }
jnxoptIfODUkTtpDEGThr OBJECT-TYPE
SYNTAX JnxoptIfDEGThr
UNITS "percentage"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to jnxoptIfODUkDEGThr.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfODUkDirectionality has the value source(2).
The default value of this object is Severely Errored Second
(SES) Estimator (See ITU-T G.7710)."
::= { jnxoptIfODUkTtpConfigEntry 7 }
jnxoptIfODUkTtpDEGM OBJECT-TYPE
SYNTAX JnxoptIfDEGM
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if jnxoptIfODUkDEGM
consecutive bad PM Seconds are detected.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfODUkDirectionality has the value source(2).
The default value of this object is 7 (See ITU-T G.7710)."
::= { jnxoptIfODUkTtpConfigEntry 8 }
jnxoptIfODUkTtpCurrentStatus OBJECT-TYPE
SYNTAX BITS {
oci(0),
lck(1),
tim(2),
deg(3),
bdi(4),
ssf(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the defect condition of the entity, if any.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where jnxoptIfODUkDirectionality has the value source(2)."
::= { jnxoptIfODUkTtpConfigEntry 9 }
-- ODUk Position Sequence table
jnxoptIfODUkPositionSeqTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfODUkPositionSeqEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of ODUk Position Sequence information."
::= { jnxoptIfODUk 3 }
jnxoptIfODUkPositionSeqEntry OBJECT-TYPE
SYNTAX JnxoptIfODUkPositionSeqEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains ODUk position sequence
information of an ODUk interface. The ODUk interface
is identified by the ifIndex. Associated with each
ODUk interface there may be one of more conceptual
rows in the jnxoptIfODUkPositionSeqTable. Each row
represents a TCM or GCC12 access function within the
associated ODUk interface. Rows of the
jnxoptIfODUkPositionSeqTable table are created/deleted
as the result of the creation/deletion of the jnxoptIfODUkT
or jnxoptIfGCC12 entities."
INDEX { ifIndex, jnxoptIfODUkPositionSeqIndex }
::= { jnxoptIfODUkPositionSeqTable 1 }
JnxoptIfODUkPositionSeqEntry ::=
SEQUENCE {
jnxoptIfODUkPositionSeqIndex Unsigned32,
jnxoptIfODUkPositionSeqPosition Unsigned32,
jnxoptIfODUkPositionSeqPointer RowPointer
}
jnxoptIfODUkPositionSeqIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This variable identifies a row in the
jnxoptIfODUkPositionSeqTable Table.
Each row of the jnxoptIfODUkPositionSeqTable Table
represents a TCM or GCC12 access function within the
associated ODUk interface."
::= { jnxoptIfODUkPositionSeqEntry 1 }
jnxoptIfODUkPositionSeqPosition OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the position of the TCM or
GCC12 access function within the sequence of TCMs &
GCC12 access functions of the associated ODUk
interface. The TCM or GCC12 presented by this row is
referenced by the jnxoptIfODUkPositionSeqPointer variable."
::= { jnxoptIfODUkPositionSeqEntry 2 }
jnxoptIfODUkPositionSeqPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable identifies the TCM or GCC12 access function
by pointing to the corresponding jnxoptIfODUkT or jnxoptIfGCC12
entity."
::= { jnxoptIfODUkPositionSeqEntry 3 }
-- ODUk Non-intrusive monitoring (Nim) config table
jnxoptIfODUkNimConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfODUkNimConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of ODUkNim configuration information."
::= { jnxoptIfODUk 4 }
jnxoptIfODUkNimConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfODUkNimConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains ODUkNim configuration
information of an interface. Each instance must
correspond to an instance of jnxoptIfODUkConfigEntry
for which jnxoptIfODUkTtpPresent has the value false(2).
Instances of this conceptual row persist across
agent restarts, and read-create columns other
than the status column may be modified while the
row is active."
INDEX { ifIndex, jnxoptIfODUkNimDirectionality }
::= { jnxoptIfODUkNimConfigTable 1 }
JnxoptIfODUkNimConfigEntry ::=
SEQUENCE {
jnxoptIfODUkNimDirectionality JnxoptIfSinkOrSource,
jnxoptIfODUkNimDAPIExpected JnxoptIfExDAPI,
jnxoptIfODUkNimSAPIExpected JnxoptIfExSAPI,
jnxoptIfODUkNimTraceIdentifierAccepted JnxoptIfAcTI,
jnxoptIfODUkNimTIMDetMode JnxoptIfTIMDetMode,
jnxoptIfODUkNimTIMActEnabled TruthValue,
jnxoptIfODUkNimDEGThr JnxoptIfDEGThr,
jnxoptIfODUkNimDEGM JnxoptIfDEGM,
jnxoptIfODUkNimCurrentStatus BITS,
jnxoptIfODUkNimRowStatus RowStatus
}
jnxoptIfODUkNimDirectionality OBJECT-TYPE
SYNTAX JnxoptIfSinkOrSource
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the monitor point for the ODUk Path non-intrusive
monitoring function. The value source(2) is not allowed
if the corresponding instance of jnxoptIfODUkDirectionality
has the value sink(1), and the value sink(1) is not allowed
if the corresponding instance of jnxoptIfODUkDirectionality
has the value source(2). Either the value sink(1) or
source(2) is allowed if the corresponding instance of
jnxoptIfODUkDirectionality has the value bidirectional(3).
The value sink(1) means monitoring at the sink direction
path signal of the ODUk CTP.
The value source(2) means monitoring at the source direction
path signal of the ODUk CTP. Monitoring the source direction
of an ODUk CTP is necessary in those cases where the ODUk CTP
is at an SNCP (Subnetwork Connection Protection) end (e.g., see
Figure I.1.2/G.874.1). If one would like to get the performance
of the protected connection, one cannot use the NIM function
at both ODUk CTP sinks (before the matrix), instead one should
monitor the signal at the source ODUk CTP after the matrix."
::= { jnxoptIfODUkNimConfigEntry 1 }
jnxoptIfODUkNimDAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExDAPI
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The DAPI expected by the receiver.
This object has no effect if jnxoptIfODUkNimTIMDetMode has
the value off(1) or sapi(3)."
::= { jnxoptIfODUkNimConfigEntry 2 }
jnxoptIfODUkNimSAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExSAPI
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SAPI expected by the receiver.
This object has no effect if jnxoptIfODUkNimTIMDetMode has
the value off(1) or dapi(2)."
::= { jnxoptIfODUkNimConfigEntry 3 }
jnxoptIfODUkNimTraceIdentifierAccepted OBJECT-TYPE
SYNTAX JnxoptIfAcTI
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual trace identifier accepted. The value of
this object is unspecified if jnxoptIfODUkNimCurrentStatus
has any of the bit positions oci(0), lck(1), or ssf(5)
set or if jnxoptIfODUkNimRowStatus has any value other
than active(1)."
::= { jnxoptIfODUkNimConfigEntry 4 }
jnxoptIfODUkNimTIMDetMode OBJECT-TYPE
SYNTAX JnxoptIfTIMDetMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function."
::= { jnxoptIfODUkNimConfigEntry 5 }
jnxoptIfODUkNimTIMActEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled."
::= { jnxoptIfODUkNimConfigEntry 6 }
jnxoptIfODUkNimDEGThr OBJECT-TYPE
SYNTAX JnxoptIfDEGThr
UNITS "percentage"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad
if the percentage of detected errored blocks in that second is
greater than or equal to jnxoptIfODUkNimDEGThr."
::= { jnxoptIfODUkNimConfigEntry 7 }
jnxoptIfODUkNimDEGM OBJECT-TYPE
SYNTAX JnxoptIfDEGM
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if jnxoptIfODUkNimDEGM
consecutive bad PM Seconds are detected."
::= { jnxoptIfODUkNimConfigEntry 8 }
jnxoptIfODUkNimCurrentStatus OBJECT-TYPE
SYNTAX BITS {
oci(0),
lck(1),
tim(2),
deg(3),
bdi(4),
ssf(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the defect condition of the entity, if
any. The value of this object is unspecified if
jnxoptIfODUkNimRowStatus has any value other than
active(1)."
::= { jnxoptIfODUkNimConfigEntry 9 }
jnxoptIfODUkNimRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This columnar object is used for creating and deleting
a conceptual row of the jnxoptIfODUkNim config table.
It is used to model the activateNim and deactivateNim
operations of an OTUk_CTP for non-intrusive monitoring
control as defined in G.874.1. Setting RowStatus to
createAndGo or createAndWait implies activateNim.
Setting RowStatus to destroy implies deactivateNim."
::= { jnxoptIfODUkNimConfigEntry 10 }
-- GCC12 config table
jnxoptIfGCC12ConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfGCC12ConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of GCC12 configuration information.
The GCC function processes the GCC overhead bytes passing
through them but leave the remainder of the ODUk overhead
and payload data alone."
::= { jnxoptIfODUk 5 }
jnxoptIfGCC12ConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfGCC12ConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains GCC12 configuration
information of an interface. Each instance must
correspond to an instance of jnxoptIfODUkConfigEntry.
Separate instances providing GCC1-only access and
GCC2-only access may exist for a given ifIndex value,
or a single instance providing GCC1 + GCC2 may exist,
but a GCC1 + GCC2 instance may not coexist with a
GCC1-only or GCC2-only instance.
Instances of this conceptual row persist across agent
restarts."
INDEX { ifIndex, jnxoptIfGCC12Codirectional, jnxoptIfGCC12GCCAccess }
::= { jnxoptIfGCC12ConfigTable 1 }
JnxoptIfGCC12ConfigEntry ::=
SEQUENCE {
jnxoptIfGCC12Codirectional TruthValue,
jnxoptIfGCC12GCCAccess INTEGER,
jnxoptIfGCC12GCCPassThrough TruthValue,
jnxoptIfGCC12Application SnmpAdminString,
jnxoptIfGCC12RowStatus RowStatus
}
jnxoptIfGCC12Codirectional OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the directionality of the GCC12 termination with
respect to the associated ODUk CTP. The value true(1) means
that the sink part of the GCC12 extracts COMMS data from the
signal at the input to the ODUk CTP sink and the source part
of the GCC12 inserts COMMS data into the signal at the output
of the ODUk CTP source. The value false(2) means that the
sink part of the GCC12 extracts COMMS data from the signal at
the output of the ODUk CTP source and the source part of the
GCC12 inserts COMMS data into the signal at the input of the
ODUk CTP sink. This attribute may assume either value when
the corresponding instance of jnxoptIfODUkTtpPresent has the
value false(2). When the value of the corresponding instance
of jnxoptIfODUkTtpPresent is true(1) then the only value allowed
for this attribute is true(1)."
::= { jnxoptIfGCC12ConfigEntry 1 }
jnxoptIfGCC12GCCAccess OBJECT-TYPE
SYNTAX INTEGER {
gcc1 (1),
gcc2 (2),
gcc1and2 (3)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the GCC access represented by the entity."
::= { jnxoptIfGCC12ConfigEntry 2 }
jnxoptIfGCC12GCCPassThrough OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Controls whether the selected GCC overhead bytes are passed
through or modified. The value true(1) means that the selected
GCC overhead bytes are passed through unmodified from the ODUk
CTP input to the ODUk CTP output. The value false(2) means that
the selected GCC overhead bytes are set to zero at the ODUk CTP
output after the extraction of the COMMS data. This object has
no effect if the corresponding instance of jnxoptIfODUkTtpPresent
has the value true(1).
The value of this object may not be changed when
jnxoptIfGCC12RowStatus has the value active(1)."
::= { jnxoptIfGCC12ConfigEntry 3 }
jnxoptIfGCC12Application OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the application transported by the GCC12 entity.
Example applications are ECC, User data channel.
The value of this object may not be changed when
jnxoptIfGCC12RowStatus has the value active(1)."
::= { jnxoptIfGCC12ConfigEntry 4 }
jnxoptIfGCC12RowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This columnar object is used for creating and deleting
a conceptual row of the jnxoptIfGCC12 config table. It is
used to model the addGCC12Access and removeGCC12Access
operations of an ODUk_CTP or ODUk_TTP for GCC12 access
control as defined in G.874.1. Setting RowStatus to
createAndGo or createAndWait implies addGCC12Access.
Setting RowStatus to destroy implies removeGCC12Access.
Successful addition/removal of the GCC12 access function
will result in updating the
jnxoptIfODUkPositionSeqCurrentSize variable and the
jnxoptIfODUkPositionSeqTable table of the associated
ODUk entry in the jnxoptIfODUkConfigTable."
::= { jnxoptIfGCC12ConfigEntry 5 }
-- the jnxoptIfODUkT group
-- This group handles the configuration information
-- for the ODUkT layers.
-- ODUkT config table
jnxoptIfODUkTConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfODUkTConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of ODUkT configuration information."
::= { jnxoptIfODUkT 1 }
jnxoptIfODUkTConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfODUkTConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains ODUkT configuration
information of an interface. Each instance must
correspond to an instance of jnxoptIfODUkConfigEntry.
Rows in this table are mutually exclusive with rows
in the ODUkT NIM config table -- in other words, this
row object may not be instantiated for a given pair
of ifIndex and TCM field values if a corresponding
instance of jnxoptIfODUkTNimConfigEntry already exists.
Instances of this conceptual row persist across agent
restarts. Except where noted otherwise, read-create
columns other than the status column may be modified
while the row is active."
INDEX { ifIndex, jnxoptIfODUkTTcmField, jnxoptIfODUkTCodirectional }
::= { jnxoptIfODUkTConfigTable 1 }
JnxoptIfODUkTConfigEntry ::=
SEQUENCE {
jnxoptIfODUkTTcmField Unsigned32,
jnxoptIfODUkTCodirectional TruthValue,
jnxoptIfODUkTTraceIdentifierTransmitted JnxoptIfTxTI,
jnxoptIfODUkTDAPIExpected JnxoptIfExDAPI,
jnxoptIfODUkTSAPIExpected JnxoptIfExSAPI,
jnxoptIfODUkTTraceIdentifierAccepted JnxoptIfAcTI,
jnxoptIfODUkTTIMDetMode JnxoptIfTIMDetMode,
jnxoptIfODUkTTIMActEnabled TruthValue,
jnxoptIfODUkTDEGThr JnxoptIfDEGThr,
jnxoptIfODUkTDEGM JnxoptIfDEGM,
jnxoptIfODUkTSinkMode INTEGER,
jnxoptIfODUkTSinkLockSignalAdminState INTEGER,
jnxoptIfODUkTSourceLockSignalAdminState INTEGER,
jnxoptIfODUkTCurrentStatus BITS,
jnxoptIfODUkTRowStatus RowStatus
}
jnxoptIfODUkTTcmField OBJECT-TYPE
SYNTAX Unsigned32 (1..6)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the tandem connection monitoring
field of the ODUk OH. Valid values are
integers from 1 to 6."
::= { jnxoptIfODUkTConfigEntry 1 }
jnxoptIfODUkTCodirectional OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the directionality of the ODUkT termination point with
respect to the associated ODUk CTP. The value true(1) means
that the sink part of the ODUkT TP extracts TCM data from the
signal at the input to the ODUk CTP sink and the source part
of the ODUkT TP inserts TCM data into the signal at the output
of the ODUk CTP source. The value false(2) means that the
sink part of the ODUkT TP extracts TCM data from the signal at
the output of the ODUk CTP source and the source part of the
ODUkT TP inserts TCM data into the signal at the input of the
ODUk CTP sink. This attribute may assume either value when
the corresponding instance of jnxoptIfODUkTtpPresent has the
value false(2). When the value of the corresponding instance
of jnxoptIfODUkTtpPresent is true(1) then the only value allowed
for this attribute is true(1)."
::= { jnxoptIfODUkTConfigEntry 2 }
jnxoptIfODUkTTraceIdentifierTransmitted OBJECT-TYPE
SYNTAX JnxoptIfTxTI
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The trace identifier transmitted.
This object is applicable only to the following three cases.
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value false(2), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value true(1).
It must not be instantiated in rows for all other cases."
::= { jnxoptIfODUkTConfigEntry 3 }
jnxoptIfODUkTDAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExDAPI
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The DAPI expected by the receiver.
This object is applicable only to the following three cases.
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
This object has no effect when jnxoptIfODUkTTIMDetMode has
the value off(1)."
::= { jnxoptIfODUkTConfigEntry 4 }
jnxoptIfODUkTSAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExSAPI
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SAPI expected by the receiver.
This object is applicable only to the following three cases.
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
This object has no effect when jnxoptIfODUkTTIMDetMode has
the value off(1)."
::= { jnxoptIfODUkTConfigEntry 5 }
jnxoptIfODUkTTraceIdentifierAccepted OBJECT-TYPE
SYNTAX JnxoptIfAcTI
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual trace identifier accepted.
This object is applicable only to the following three cases.
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
The value of this object is unspecified when
jnxoptIfODUkTCurrentStatus indicates a near-end defect
(i.e., oci(0), lck(1), ssf(5)) that prevents extraction
of the trace message."
::= { jnxoptIfODUkTConfigEntry 6 }
jnxoptIfODUkTTIMDetMode OBJECT-TYPE
SYNTAX JnxoptIfTIMDetMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function.
This object is applicable only to the following three cases.
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
The default value of this object is off(1)."
::= { jnxoptIfODUkTConfigEntry 7 }
jnxoptIfODUkTTIMActEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled.
This object is applicable only to the following three cases.
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
This object has no effect when jnxoptIfODUkTTIMDetMode has
the value off(1).
The default value of this object is false(2)."
::= { jnxoptIfODUkTConfigEntry 8 }
jnxoptIfODUkTDEGThr OBJECT-TYPE
SYNTAX JnxoptIfDEGThr
UNITS "percentage"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to jnxoptIfODUkTDEGThr.
This object is applicable only to the following three cases.
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
The default value of this object is Severely Errored Second
(SES) Estimator (See ITU-T G.7710)."
::= { jnxoptIfODUkTConfigEntry 9 }
jnxoptIfODUkTDEGM OBJECT-TYPE
SYNTAX JnxoptIfDEGM
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if jnxoptIfODUkTDEGM
consecutive bad PM Seconds are detected.
This object is applicable only to the following three cases.
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
The default value of this object is 7 (See ITU-T G.7710)."
::= { jnxoptIfODUkTConfigEntry 10 }
jnxoptIfODUkTSinkMode OBJECT-TYPE
SYNTAX INTEGER {
operational (1),
monitor (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This variable specifies the TCM mode at the entity.
The value operational(1) means that TCM Overhead (TCMOH)
processes (see ITU-T G.798) shall be
performed and consequent actions for AIS, Trail
Signal Fail (TSF), Trail Signal Degraded (TSD) shall be
initiated in case of defects.
The value monitor(2) means that TCMOH processes shall be
performed but consequent actions for AIS, Trail
Server Failure (TSF), Trail Server Degraded (TSD) shall _not_ be
initiated in case of defects.
This object is applicable only when the value of
jnxoptIfODUkTtpPresent is false(2) and also either one of the
following three cases holds:
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases."
::= { jnxoptIfODUkTConfigEntry 11 }
jnxoptIfODUkTSinkLockSignalAdminState OBJECT-TYPE
SYNTAX INTEGER {
locked(1),
normal(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Provides the capability to provision the LOCK signal, which
is one of the ODUk maintenance signals, at the ODUKT sink. When
a Tandem Connection endpoint is set to admin state locked,
it inserts the ODUk-LCK signal in the sink direction.
This object is applicable only when the value of
jnxoptIfODUkTtpPresent is false(2) and also either one of the
following three cases holds:
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases."
::= { jnxoptIfODUkTConfigEntry 12 }
jnxoptIfODUkTSourceLockSignalAdminState OBJECT-TYPE
SYNTAX INTEGER {
locked(1),
normal(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Provides the capability to provision the LOCK signal, which
is one of the ODUk maintenance signals, at the source.
When a Tandem Connection endpoint is set to admin state
locked, it inserts the ODUk-LCK signal in the source
direction.
This object is applicable only when either one of the
following three cases holds:
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value false(2), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value true(1).
It must not be instantiated in rows for all other cases."
::= { jnxoptIfODUkTConfigEntry 13 }
jnxoptIfODUkTCurrentStatus OBJECT-TYPE
SYNTAX BITS {
oci(0),
lck(1),
tim(2),
deg(3),
bdi(4),
ssf(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the defect condition of the entity, if any.
This object is applicable only when either one of the
following three cases holds:
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases."
::= { jnxoptIfODUkTConfigEntry 14 }
jnxoptIfODUkTRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This columnar object is used for creating and deleting a
conceptual row of the jnxoptIfODUkT config table.
It is used to model the addTCM and removeTCM operations of an
ODUk_CTP or ODUk_TTP for Tandem connection monitoring as defined
in ITU-T G.874.1.
Setting RowStatus to createAndGo or createAndWait implies addTCM.
Setting RowStatus to destroy implies removeTCM.
Successful addition/removal of TCM will result in updating the
jnxoptIfODUkTcmFieldsInUse and jnxoptIfODUkPositionSeqCurrentSize
variables and the jnxoptIfODUkPositionSeqTable table of the
associated ODUk entry in the jnxoptIfODUkConfigTable."
::= { jnxoptIfODUkTConfigEntry 15 }
-- ODUkT Non-intrusive monitoring (Nim) config table
jnxoptIfODUkTNimConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxoptIfODUkTNimConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of ODUkTNim configuration information."
::= { jnxoptIfODUkT 2 }
jnxoptIfODUkTNimConfigEntry OBJECT-TYPE
SYNTAX JnxoptIfODUkTNimConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row that contains ODUkTNim configuration
information of an interface. Each instance must
correspond to an instance of jnxoptIfODUkConfigEntry.
Rows in this table are mutually exclusive with rows
in the ODUkT config table -- in other words, this
row object may not be instantiated for a given pair
of ifIndex and TCM field values if a corresponding
instance of jnxoptIfODUkTConfigEntry already exists.
Instances of this conceptual row persist across
agent restarts, and read-create columns other
than the status column may be modified while the
row is active."
INDEX {ifIndex, jnxoptIfODUkTNimTcmField, jnxoptIfODUkTNimDirectionality}
::= { jnxoptIfODUkTNimConfigTable 1 }
JnxoptIfODUkTNimConfigEntry ::=
SEQUENCE {
jnxoptIfODUkTNimTcmField Unsigned32,
jnxoptIfODUkTNimDirectionality JnxoptIfSinkOrSource,
jnxoptIfODUkTNimDAPIExpected JnxoptIfExDAPI,
jnxoptIfODUkTNimSAPIExpected JnxoptIfExSAPI,
jnxoptIfODUkTNimTraceIdentifierAccepted JnxoptIfAcTI,
jnxoptIfODUkTNimTIMDetMode JnxoptIfTIMDetMode,
jnxoptIfODUkTNimTIMActEnabled TruthValue,
jnxoptIfODUkTNimDEGThr JnxoptIfDEGThr,
jnxoptIfODUkTNimDEGM JnxoptIfDEGM,
jnxoptIfODUkTNimCurrentStatus BITS,
jnxoptIfODUkTNimRowStatus RowStatus
}
jnxoptIfODUkTNimTcmField OBJECT-TYPE
SYNTAX Unsigned32 (1..6)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the tandem connection monitoring
field of the ODUk OH on which non-intrusive monitoring
is performed. Valid values are
integers from 1 to 6."
::= { jnxoptIfODUkTNimConfigEntry 1 }
jnxoptIfODUkTNimDirectionality OBJECT-TYPE
SYNTAX JnxoptIfSinkOrSource
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the monitor point for the ODUk TCM non-intrusive
monitoring function. The value source(2) is not allowed
if the corresponding instance of jnxoptIfODUkDirectionality
has the value sink(1), and the value sink(1) is not allowed
if the corresponding instance of jnxoptIfODUkDirectionality
has the value source(2). Either the value sink(1) or
source(2) is allowed if the corresponding instance of
jnxoptIfODUkDirectionality has the value bidirectional(3).
The value sink(1) means monitoring at the sink direction
TCM signal of the ODUk CTP.
The value source(2) means monitoring at the source direction
path signal of the ODUk CTP."
::= { jnxoptIfODUkTNimConfigEntry 2 }
jnxoptIfODUkTNimDAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExDAPI
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The DAPI expected by the receiver.
This object has no effect if jnxoptIfODUkTNimTIMDetMode has
the value off(1) or sapi(3)."
::= { jnxoptIfODUkTNimConfigEntry 3 }
jnxoptIfODUkTNimSAPIExpected OBJECT-TYPE
SYNTAX JnxoptIfExSAPI
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The SAPI expected by the receiver.
This object has no effect if jnxoptIfODUkTNimTIMDetMode has
the value off(1) or dapi(2)."
::= { jnxoptIfODUkTNimConfigEntry 4 }
jnxoptIfODUkTNimTraceIdentifierAccepted OBJECT-TYPE
SYNTAX JnxoptIfAcTI
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual trace identifier accepted. The value of
this object is unspecified if jnxoptIfODUkTNimCurrentStatus
has any of the bit positions oci(0), lck(1), or ssf(5)
set or if jnxoptIfODUkTNimRowStatus has any value other
than active(1)."
::= { jnxoptIfODUkTNimConfigEntry 5 }
jnxoptIfODUkTNimTIMDetMode OBJECT-TYPE
SYNTAX JnxoptIfTIMDetMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function."
::= { jnxoptIfODUkTNimConfigEntry 6 }
jnxoptIfODUkTNimTIMActEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled."
::= { jnxoptIfODUkTNimConfigEntry 7 }
jnxoptIfODUkTNimDEGThr OBJECT-TYPE
SYNTAX JnxoptIfDEGThr
UNITS "percentage"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to jnxoptIfODUkTNimDEGThr."
::= { jnxoptIfODUkTNimConfigEntry 8 }
jnxoptIfODUkTNimDEGM OBJECT-TYPE
SYNTAX JnxoptIfDEGM
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if jnxoptIfODUkTNimDEGM
consecutive bad PM Seconds are detected."
::= { jnxoptIfODUkTNimConfigEntry 9 }
jnxoptIfODUkTNimCurrentStatus OBJECT-TYPE
SYNTAX BITS {
oci(0),
lck(1),
tim(2),
deg(3),
bdi(4),
ssf(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the defect condition of the entity, if any.
The value of this object is unspecified if
jnxoptIfODUkTNimRowStatus has any value other than
active(1)."
::= { jnxoptIfODUkTNimConfigEntry 10 }
jnxoptIfODUkTNimRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This columnar object is used for creating and deleting a
conceptual row of the jnxoptIfODUkTNim config table.
It is used to model the addTCM and removeTCM operations of an
ODUk_CTP or ODUk_TTP for non-intrusive Tandem connection
monitoring as defined in ITU-T G.874.1.
Setting RowStatus to createAndGo or createAndWait implies addTCM.
Setting RowStatus to destroy implies removeTCM.
Successful addition/removal of Nim TCM will result in updating
the jnxoptIfODUkPositionSeqCurrentSize variable and the
jnxoptIfODUkPositionSeqTable table of the associated ODUk entry
in the jnxoptIfODUkConfigTable."
::= { jnxoptIfODUkTNimConfigEntry 11 }
-- units of conformance
jnxoptIfOTMnGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTMnOrder,
jnxoptIfOTMnReduced,
jnxoptIfOTMnBitRates,
jnxoptIfOTMnInterfaceType,
jnxoptIfOTMnTcmMax,
jnxoptIfOTMnOpticalReach
}
STATUS current
DESCRIPTION
"A collection of OTMn structure information objects."
::= { jnxoptIfGroups 1 }
jnxoptIfPerfMonGroup OBJECT-GROUP
OBJECTS {
jnxoptIfPerfMonCurrentTimeElapsed,
jnxoptIfPerfMonCurDayTimeElapsed,
jnxoptIfPerfMonIntervalNumIntervals,
jnxoptIfPerfMonIntervalNumInvalidIntervals
}
STATUS current
DESCRIPTION
"A collection of performance monitoring interval objects."
::= { jnxoptIfGroups 2 }
jnxoptIfOTSnCommonGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnDirectionality
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all OTSn interfaces."
::= { jnxoptIfGroups 3 }
jnxoptIfOTSnSourceGroupFull OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnTraceIdentifierTransmitted
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to full-functionality/IaDI OTSn
interfaces that support source functions."
::= { jnxoptIfGroups 4 }
jnxoptIfOTSnAPRStatusGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnAprStatus
}
STATUS current
DESCRIPTION
"A collection of objects applicable to
OTSn interfaces that support Automatic
Power Reduction functions."
::= { jnxoptIfGroups 5 }
jnxoptIfOTSnAPRControlGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnAprControl
}
STATUS current
DESCRIPTION
"A collection of objects applicable to
OTSn interfaces that provide Automatic
Power Reduction control functions."
::= { jnxoptIfGroups 6 }
jnxoptIfOTSnSinkGroupBasic OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnCurrentStatus
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all OTSn interfaces that
support sink functions."
::= { jnxoptIfGroups 7 }
jnxoptIfOTSnSinkGroupFull OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnDAPIExpected,
jnxoptIfOTSnSAPIExpected,
jnxoptIfOTSnTraceIdentifierAccepted,
jnxoptIfOTSnTIMDetMode,
jnxoptIfOTSnTIMActEnabled
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to full-functionality/IaDI OTSn
interfaces that support sink functions."
::= { jnxoptIfGroups 8 }
jnxoptIfOTSnSinkPreOtnPMGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnSinkCurrentSuspectedFlag,
jnxoptIfOTSnSinkCurrentInputPower,
jnxoptIfOTSnSinkCurrentLowInputPower,
jnxoptIfOTSnSinkCurrentHighInputPower,
jnxoptIfOTSnSinkCurrentOutputPower,
jnxoptIfOTSnSinkCurrentLowOutputPower,
jnxoptIfOTSnSinkCurrentHighOutputPower,
jnxoptIfOTSnSinkIntervalSuspectedFlag,
jnxoptIfOTSnSinkIntervalLastInputPower,
jnxoptIfOTSnSinkIntervalLowInputPower,
jnxoptIfOTSnSinkIntervalHighInputPower,
jnxoptIfOTSnSinkIntervalLastOutputPower,
jnxoptIfOTSnSinkIntervalLowOutputPower,
jnxoptIfOTSnSinkIntervalHighOutputPower,
jnxoptIfOTSnSinkCurDaySuspectedFlag,
jnxoptIfOTSnSinkCurDayLowInputPower,
jnxoptIfOTSnSinkCurDayHighInputPower,
jnxoptIfOTSnSinkCurDayLowOutputPower,
jnxoptIfOTSnSinkCurDayHighOutputPower,
jnxoptIfOTSnSinkPrevDaySuspectedFlag,
jnxoptIfOTSnSinkPrevDayLastInputPower,
jnxoptIfOTSnSinkPrevDayLowInputPower,
jnxoptIfOTSnSinkPrevDayHighInputPower,
jnxoptIfOTSnSinkPrevDayLastOutputPower,
jnxoptIfOTSnSinkPrevDayLowOutputPower,
jnxoptIfOTSnSinkPrevDayHighOutputPower
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
objects applicable to OTSn interfaces that
support sink functions."
::= { jnxoptIfGroups 9 }
jnxoptIfOTSnSinkPreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold,
jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold,
jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold,
jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
threshold objects applicable to OTSn interfaces
that support sink functions."
::= { jnxoptIfGroups 10 }
jnxoptIfOTSnSourcePreOtnPMGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnSrcCurrentSuspectedFlag,
jnxoptIfOTSnSrcCurrentOutputPower,
jnxoptIfOTSnSrcCurrentLowOutputPower,
jnxoptIfOTSnSrcCurrentHighOutputPower,
jnxoptIfOTSnSrcCurrentInputPower,
jnxoptIfOTSnSrcCurrentLowInputPower,
jnxoptIfOTSnSrcCurrentHighInputPower,
jnxoptIfOTSnSrcIntervalSuspectedFlag,
jnxoptIfOTSnSrcIntervalLastOutputPower,
jnxoptIfOTSnSrcIntervalLowOutputPower,
jnxoptIfOTSnSrcIntervalHighOutputPower,
jnxoptIfOTSnSrcIntervalLastInputPower,
jnxoptIfOTSnSrcIntervalLowInputPower,
jnxoptIfOTSnSrcIntervalHighInputPower,
jnxoptIfOTSnSrcCurDaySuspectedFlag,
jnxoptIfOTSnSrcCurDayLowOutputPower,
jnxoptIfOTSnSrcCurDayHighOutputPower,
jnxoptIfOTSnSrcCurDayLowInputPower,
jnxoptIfOTSnSrcCurDayHighInputPower,
jnxoptIfOTSnSrcPrevDaySuspectedFlag,
jnxoptIfOTSnSrcPrevDayLastOutputPower,
jnxoptIfOTSnSrcPrevDayLowOutputPower,
jnxoptIfOTSnSrcPrevDayHighOutputPower,
jnxoptIfOTSnSrcPrevDayLastInputPower,
jnxoptIfOTSnSrcPrevDayLowInputPower,
jnxoptIfOTSnSrcPrevDayHighInputPower
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
objects applicable to OTSn interfaces that
support source functions."
::= { jnxoptIfGroups 11 }
jnxoptIfOTSnSourcePreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold,
jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold,
jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold,
jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
threshold objects applicable to OTSn interfaces
that support source functions."
::= { jnxoptIfGroups 12 }
jnxoptIfOMSnCommonGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOMSnDirectionality
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all OMSn interfaces."
::= { jnxoptIfGroups 13 }
jnxoptIfOMSnSinkGroupBasic OBJECT-GROUP
OBJECTS {
jnxoptIfOMSnCurrentStatus
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all OMSn interfaces that
support sink functions."
::= { jnxoptIfGroups 14 }
jnxoptIfOMSnSinkPreOtnPMGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOMSnSinkCurrentSuspectedFlag,
jnxoptIfOMSnSinkCurrentAggregatedInputPower,
jnxoptIfOMSnSinkCurrentLowAggregatedInputPower,
jnxoptIfOMSnSinkCurrentHighAggregatedInputPower,
jnxoptIfOMSnSinkCurrentOutputPower,
jnxoptIfOMSnSinkCurrentLowOutputPower,
jnxoptIfOMSnSinkCurrentHighOutputPower,
jnxoptIfOMSnSinkIntervalSuspectedFlag,
jnxoptIfOMSnSinkIntervalLastAggregatedInputPower,
jnxoptIfOMSnSinkIntervalLowAggregatedInputPower,
jnxoptIfOMSnSinkIntervalHighAggregatedInputPower,
jnxoptIfOMSnSinkIntervalLastOutputPower,
jnxoptIfOMSnSinkIntervalLowOutputPower,
jnxoptIfOMSnSinkIntervalHighOutputPower,
jnxoptIfOMSnSinkCurDaySuspectedFlag,
jnxoptIfOMSnSinkCurDayLowAggregatedInputPower,
jnxoptIfOMSnSinkCurDayHighAggregatedInputPower,
jnxoptIfOMSnSinkCurDayLowOutputPower,
jnxoptIfOMSnSinkCurDayHighOutputPower,
jnxoptIfOMSnSinkPrevDaySuspectedFlag,
jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower,
jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower,
jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower,
jnxoptIfOMSnSinkPrevDayLastOutputPower,
jnxoptIfOMSnSinkPrevDayLowOutputPower,
jnxoptIfOMSnSinkPrevDayHighOutputPower
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
objects applicable to OMSn interfaces that
support sink functions."
::= { jnxoptIfGroups 15 }
jnxoptIfOMSnSinkPreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold,
jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold,
jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold,
jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
threshold objects applicable to OMSn interfaces
that support sink functions."
::= { jnxoptIfGroups 16 }
jnxoptIfOMSnSourcePreOtnPMGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOMSnSrcCurrentSuspectedFlag,
jnxoptIfOMSnSrcCurrentOutputPower,
jnxoptIfOMSnSrcCurrentLowOutputPower,
jnxoptIfOMSnSrcCurrentHighOutputPower,
jnxoptIfOMSnSrcCurrentAggregatedInputPower,
jnxoptIfOMSnSrcCurrentLowAggregatedInputPower,
jnxoptIfOMSnSrcCurrentHighAggregatedInputPower,
jnxoptIfOMSnSrcIntervalSuspectedFlag,
jnxoptIfOMSnSrcIntervalLastOutputPower,
jnxoptIfOMSnSrcIntervalLowOutputPower,
jnxoptIfOMSnSrcIntervalHighOutputPower,
jnxoptIfOMSnSrcIntervalLastAggregatedInputPower,
jnxoptIfOMSnSrcIntervalLowAggregatedInputPower,
jnxoptIfOMSnSrcIntervalHighAggregatedInputPower,
jnxoptIfOMSnSrcCurDaySuspectedFlag,
jnxoptIfOMSnSrcCurDayLowOutputPower,
jnxoptIfOMSnSrcCurDayHighOutputPower,
jnxoptIfOMSnSrcCurDayLowAggregatedInputPower,
jnxoptIfOMSnSrcCurDayHighAggregatedInputPower,
jnxoptIfOMSnSrcPrevDaySuspectedFlag,
jnxoptIfOMSnSrcPrevDayLastOutputPower,
jnxoptIfOMSnSrcPrevDayLowOutputPower,
jnxoptIfOMSnSrcPrevDayHighOutputPower,
jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower,
jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower,
jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
objects applicable to OMSn interfaces that
support source functions."
::= { jnxoptIfGroups 17 }
jnxoptIfOMSnSourcePreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold,
jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold,
jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold,
jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
threshold objects applicable to OMSn interfaces that
that support source functions."
::= { jnxoptIfGroups 18 }
jnxoptIfOChGroupCommonGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChGroupDirectionality
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all OChGroup interfaces."
::= { jnxoptIfGroups 19 }
jnxoptIfOChGroupSinkPreOtnPMGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChGroupSinkCurrentSuspectedFlag,
jnxoptIfOChGroupSinkCurrentAggregatedInputPower,
jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower,
jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower,
jnxoptIfOChGroupSinkCurrentOutputPower,
jnxoptIfOChGroupSinkCurrentLowOutputPower,
jnxoptIfOChGroupSinkCurrentHighOutputPower,
jnxoptIfOChGroupSinkIntervalSuspectedFlag,
jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower,
jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower,
jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower,
jnxoptIfOChGroupSinkIntervalLastOutputPower,
jnxoptIfOChGroupSinkIntervalLowOutputPower,
jnxoptIfOChGroupSinkIntervalHighOutputPower,
jnxoptIfOChGroupSinkCurDaySuspectedFlag,
jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower,
jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower,
jnxoptIfOChGroupSinkCurDayLowOutputPower,
jnxoptIfOChGroupSinkCurDayHighOutputPower,
jnxoptIfOChGroupSinkPrevDaySuspectedFlag,
jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower,
jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower,
jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower,
jnxoptIfOChGroupSinkPrevDayLastOutputPower,
jnxoptIfOChGroupSinkPrevDayLowOutputPower,
jnxoptIfOChGroupSinkPrevDayHighOutputPower
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
objects applicable to OChGroup interfaces that
support sink functions."
::= { jnxoptIfGroups 20 }
jnxoptIfOChGroupSinkPreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold,
jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold,
jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold,
jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
threshold objects applicable to OChGroup interfaces
that support sink functions."
::= { jnxoptIfGroups 21 }
jnxoptIfOChGroupSourcePreOtnPMGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChGroupSrcCurrentSuspectedFlag,
jnxoptIfOChGroupSrcCurrentOutputPower,
jnxoptIfOChGroupSrcCurrentLowOutputPower,
jnxoptIfOChGroupSrcCurrentHighOutputPower,
jnxoptIfOChGroupSrcCurrentAggregatedInputPower,
jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower,
jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower,
jnxoptIfOChGroupSrcIntervalSuspectedFlag,
jnxoptIfOChGroupSrcIntervalLastOutputPower,
jnxoptIfOChGroupSrcIntervalLowOutputPower,
jnxoptIfOChGroupSrcIntervalHighOutputPower,
jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower,
jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower,
jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower,
jnxoptIfOChGroupSrcCurDaySuspectedFlag,
jnxoptIfOChGroupSrcCurDayLowOutputPower,
jnxoptIfOChGroupSrcCurDayHighOutputPower,
jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower,
jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower,
jnxoptIfOChGroupSrcPrevDaySuspectedFlag,
jnxoptIfOChGroupSrcPrevDayLastOutputPower,
jnxoptIfOChGroupSrcPrevDayLowOutputPower,
jnxoptIfOChGroupSrcPrevDayHighOutputPower,
jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower,
jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower,
jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
objects applicable to OChGroup interfaces that
support source functions."
::= { jnxoptIfGroups 22 }
jnxoptIfOChGroupSourcePreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold,
jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold,
jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold,
jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
threshold objects applicable to OChGroup interfaces that
that support source functions."
::= { jnxoptIfGroups 23 }
jnxoptIfOChCommonGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChDirectionality
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all OCh interfaces."
::= { jnxoptIfGroups 24 }
jnxoptIfOChSinkGroupBasic OBJECT-GROUP
OBJECTS {
jnxoptIfOChCurrentStatus
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all OCh interfaces that
support sink functions."
::= { jnxoptIfGroups 25 }
jnxoptIfOChSinkPreOtnPMGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChSinkCurrentSuspectedFlag,
jnxoptIfOChSinkCurrentInputPower,
jnxoptIfOChSinkCurrentLowInputPower,
jnxoptIfOChSinkCurrentHighInputPower,
jnxoptIfOChSinkIntervalSuspectedFlag,
jnxoptIfOChSinkIntervalLastInputPower,
jnxoptIfOChSinkIntervalLowInputPower,
jnxoptIfOChSinkIntervalHighInputPower,
jnxoptIfOChSinkCurDaySuspectedFlag,
jnxoptIfOChSinkCurDayLowInputPower,
jnxoptIfOChSinkCurDayHighInputPower,
jnxoptIfOChSinkPrevDaySuspectedFlag,
jnxoptIfOChSinkPrevDayLastInputPower,
jnxoptIfOChSinkPrevDayLowInputPower,
jnxoptIfOChSinkPrevDayHighInputPower
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
objects applicable to OCh interfaces that
support sink functions."
::= { jnxoptIfGroups 26 }
jnxoptIfOChSinkPreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChSinkCurrentLowerInputPowerThreshold,
jnxoptIfOChSinkCurrentUpperInputPowerThreshold
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
threshold objects applicable to OCh interfaces
that support sink functions."
::= { jnxoptIfGroups 27 }
jnxoptIfOChSourcePreOtnPMGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChSrcCurrentSuspectedFlag,
jnxoptIfOChSrcCurrentOutputPower,
jnxoptIfOChSrcCurrentLowOutputPower,
jnxoptIfOChSrcCurrentHighOutputPower,
jnxoptIfOChSrcIntervalSuspectedFlag,
jnxoptIfOChSrcIntervalLastOutputPower,
jnxoptIfOChSrcIntervalLowOutputPower,
jnxoptIfOChSrcIntervalHighOutputPower,
jnxoptIfOChSrcCurDaySuspectedFlag,
jnxoptIfOChSrcCurDayLowOutputPower,
jnxoptIfOChSrcCurDayHighOutputPower,
jnxoptIfOChSrcPrevDaySuspectedFlag,
jnxoptIfOChSrcPrevDayLastOutputPower,
jnxoptIfOChSrcPrevDayLowOutputPower,
jnxoptIfOChSrcPrevDayHighOutputPower
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
objects applicable to OCh interfaces that
support source functions."
::= { jnxoptIfGroups 28 }
jnxoptIfOChSourcePreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOChSrcCurrentLowerOutputPowerThreshold,
jnxoptIfOChSrcCurrentUpperOutputPowerThreshold
}
STATUS current
DESCRIPTION
"A collection of pre-OTN performance monitoring
threshold objects applicable to OCh interfaces
that support source functions."
::= { jnxoptIfGroups 29 }
jnxoptIfOTUkCommonGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTUkDirectionality,
jnxoptIfOTUkBitRateK
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all OTUk interfaces."
::= { jnxoptIfGroups 30 }
jnxoptIfOTUkSourceGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTUkTraceIdentifierTransmitted,
jnxoptIfOTUkSourceAdaptActive
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to OTUk interfaces that
support source functions."
::= { jnxoptIfGroups 31 }
jnxoptIfOTUkSinkGroup OBJECT-GROUP
OBJECTS {
jnxoptIfOTUkDAPIExpected,
jnxoptIfOTUkSAPIExpected,
jnxoptIfOTUkTraceIdentifierAccepted,
jnxoptIfOTUkTIMDetMode,
jnxoptIfOTUkTIMActEnabled,
jnxoptIfOTUkDEGThr,
jnxoptIfOTUkDEGM,
jnxoptIfOTUkSinkAdaptActive,
jnxoptIfOTUkSinkFECEnabled,
jnxoptIfOTUkCurrentStatus
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to OTUk interfaces that
support sink functions."
::= { jnxoptIfGroups 32 }
jnxoptIfGCC0Group OBJECT-GROUP
OBJECTS {
jnxoptIfGCC0Application,
jnxoptIfGCC0RowStatus
}
STATUS current
DESCRIPTION
"A collection of GCC0 configuration objects."
::= { jnxoptIfGroups 33 }
jnxoptIfODUkGroup OBJECT-GROUP
OBJECTS {
jnxoptIfODUkDirectionality,
jnxoptIfODUkBitRateK,
jnxoptIfODUkTcmFieldsInUse,
jnxoptIfODUkPositionSeqCurrentSize,
jnxoptIfODUkPositionSeqPosition,
jnxoptIfODUkPositionSeqPointer,
jnxoptIfODUkTtpPresent
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all ODUk interfaces."
::= { jnxoptIfGroups 34 }
jnxoptIfODUkTtpSourceGroup OBJECT-GROUP
OBJECTS {
jnxoptIfODUkTtpTraceIdentifierTransmitted
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all interfaces that support
ODUk trail termination source functions."
::= { jnxoptIfGroups 35 }
jnxoptIfODUkTtpSinkGroup OBJECT-GROUP
OBJECTS {
jnxoptIfODUkTtpDAPIExpected,
jnxoptIfODUkTtpSAPIExpected,
jnxoptIfODUkTtpTraceIdentifierAccepted,
jnxoptIfODUkTtpTIMDetMode,
jnxoptIfODUkTtpTIMActEnabled,
jnxoptIfODUkTtpDEGThr,
jnxoptIfODUkTtpDEGM,
jnxoptIfODUkTtpCurrentStatus
}
STATUS current
DESCRIPTION
"A collection of ODUk configuration objects
applicable to all interfaces that support
ODUk trail termination sink functions."
::= { jnxoptIfGroups 36 }
jnxoptIfODUkNimGroup OBJECT-GROUP
OBJECTS {
jnxoptIfODUkNimDAPIExpected,
jnxoptIfODUkNimSAPIExpected,
jnxoptIfODUkNimTraceIdentifierAccepted,
jnxoptIfODUkNimTIMDetMode,
jnxoptIfODUkNimTIMActEnabled,
jnxoptIfODUkNimDEGThr,
jnxoptIfODUkNimDEGM,
jnxoptIfODUkNimCurrentStatus,
jnxoptIfODUkNimRowStatus
}
STATUS current
DESCRIPTION
"A collection of ODUk Nim configuration objects."
::= { jnxoptIfGroups 37 }
jnxoptIfGCC12Group OBJECT-GROUP
OBJECTS {
jnxoptIfGCC12GCCPassThrough,
jnxoptIfGCC12Application,
jnxoptIfGCC12RowStatus
}
STATUS current
DESCRIPTION
"A collection of GCC12 configuration objects."
::= { jnxoptIfGroups 38 }
jnxoptIfODUkTCommonGroup OBJECT-GROUP
OBJECTS {
jnxoptIfODUkTRowStatus
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all ODUkT instances."
::= { jnxoptIfGroups 39 }
jnxoptIfODUkTSourceGroup OBJECT-GROUP
OBJECTS {
jnxoptIfODUkTTraceIdentifierTransmitted,
jnxoptIfODUkTSourceLockSignalAdminState
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all ODUkT instances
that provide source functions."
::= { jnxoptIfGroups 40 }
jnxoptIfODUkTSinkGroup OBJECT-GROUP
OBJECTS {
jnxoptIfODUkTDAPIExpected,
jnxoptIfODUkTSAPIExpected,
jnxoptIfODUkTTraceIdentifierAccepted,
jnxoptIfODUkTTIMDetMode,
jnxoptIfODUkTTIMActEnabled,
jnxoptIfODUkTDEGThr,
jnxoptIfODUkTDEGM,
jnxoptIfODUkTCurrentStatus
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to all ODUkT instances
that provide sink functions."
::= { jnxoptIfGroups 41 }
jnxoptIfODUkTSinkGroupCtp OBJECT-GROUP
OBJECTS {
jnxoptIfODUkTSinkMode,
jnxoptIfODUkTSinkLockSignalAdminState
}
STATUS current
DESCRIPTION
"A collection of configuration objects
applicable to ODUkT instances not
colocated with an ODUk TTP that
provide sink functions."
::= { jnxoptIfGroups 42 }
jnxoptIfODUkTNimGroup OBJECT-GROUP
OBJECTS {
jnxoptIfODUkTNimDAPIExpected,
jnxoptIfODUkTNimSAPIExpected,
jnxoptIfODUkTNimTraceIdentifierAccepted,
jnxoptIfODUkTNimTIMDetMode,
jnxoptIfODUkTNimTIMActEnabled,
jnxoptIfODUkTNimDEGThr,
jnxoptIfODUkTNimDEGM,
jnxoptIfODUkTNimCurrentStatus,
jnxoptIfODUkTNimRowStatus
}
STATUS current
DESCRIPTION
"A collection of ODUkT Nim configuration objects."
::= { jnxoptIfGroups 43 }
-- compliance specifications
jnxoptIfOtnConfigCompl MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Implementation requirements for the OTN configuration
functions defined in this MIB module."
MODULE -- this module
MANDATORY-GROUPS {
jnxoptIfOTMnGroup,
jnxoptIfOTSnCommonGroup
}
GROUP jnxoptIfOTSnSourceGroupFull
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(196) for which the corresponding
instance of jnxoptIfOTSnDirectionality has the value
source(2) or bidirectional(3), the corresponding
instance of jnxoptIfOTMnReduced has the value false(2),
and the corresponding instance of jnxoptIfOTMnInterfaceType
specifies an OTMn interface type of 'IaDI'."
GROUP jnxoptIfOTSnAPRStatusGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(196) that support Automatic Power
Reduction functions."
GROUP jnxoptIfOTSnAPRControlGroup
DESCRIPTION
"This group is optional, but is recommended for interfaces
of ifType opticalTransport(196) that provide Automatic
Power Reduction control functions."
GROUP jnxoptIfOTSnSinkGroupBasic
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(196) for which the corresponding
instance of jnxoptIfOTSnDirectionality has the value
sink(1) or bidirectional(3)."
GROUP jnxoptIfOTSnSinkGroupFull
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(196) for which the corresponding
instance of jnxoptIfOTSnDirectionality has the value
sink(1) or bidirectional(3), the corresponding
instance of jnxoptIfOTMnReduced has the value false(2),
and the corresponding instance of jnxoptIfOTMnInterfaceType
specifies an OTMn interface type of 'IaDI'."
GROUP jnxoptIfOMSnCommonGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(196) that support access to the OMS
overhead information within the OTN Supervisory Channel."
GROUP jnxoptIfOMSnSinkGroupBasic
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(196) that support access to the OMS Overhead
information within the OSC (OTN Supervisory Channel)
for which the corresponding
instance of jnxoptIfOMSnDirectionality has the value
sink(1) or bidirectional(3)."
GROUP jnxoptIfOChGroupCommonGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannelGroup(219)."
GROUP jnxoptIfOChCommonGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(195)."
GROUP jnxoptIfOChSinkGroupBasic
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) for which the corresponding
instance of jnxoptIfOChDirectionality has the value
sink(1) or bidirectional(3)."
GROUP jnxoptIfOTUkCommonGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OTUk layer functions."
GROUP jnxoptIfOTUkSourceGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OTUk layer functions
and for which the corresponding instance of
jnxoptIfOTUkDirectionality has the value source(2) or
bidirectional(3)."
GROUP jnxoptIfOTUkSinkGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OTUk layer functions
and for which the corresponding instance of
jnxoptIfOTUkDirectionality has the value sink(1) or
bidirectional(3)."
GROUP jnxoptIfGCC0Group
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support GCC0 access functions.
It may be implemented only if the jnxoptIfOTUkCommonGroup
is also implemented."
GROUP jnxoptIfODUkGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support ODUk layer functions."
GROUP jnxoptIfODUkTtpSourceGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) for which the corresponding
instance of jnxoptIfODUkTtpPresent has the value
true(1) and for which the corresponding instance of
jnxoptIfODUkDirectionality has the value source(2) or
bidirectional(3). It may be implemented only if the
jnxoptIfODUkGroup is also implemented."
GROUP jnxoptIfODUkTtpSinkGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) for which the corresponding
instance of jnxoptIfODUkTtpPresent has the value
true(1) and for which the corresponding instance of
jnxoptIfODUkDirectionality has the value sink(1) or
bidirectional(3). It may be implemented only if the
jnxoptIfODUkGroup is also implemented."
GROUP jnxoptIfODUkNimGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) for which the corresponding
instance of jnxoptIfODUkTtpPresent has the value
false(2). It may be implemented only if the
jnxoptIfODUkGroup is also implemented."
GROUP jnxoptIfGCC12Group
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support GCC12 access functions.
It may be implemented only if the jnxoptIfODUkGroup
is also implemented."
GROUP jnxoptIfODUkTCommonGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support intrusive
tandem connection monitoring. It may be implemented
only if the jnxoptIfODUkGroup is also implemented."
GROUP jnxoptIfODUkTSourceGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support intrusive
tandem connection monitoring and for which
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value false(2), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value true(1).
It may be implemented only if the jnxoptIfODUkGroup is
also implemented."
GROUP jnxoptIfODUkTSinkGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support intrusive
tandem connection monitoring and for which
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It may be implemented only if the jnxoptIfODUkGroup is
also implemented."
GROUP jnxoptIfODUkTSinkGroupCtp
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support intrusive
tandem connection monitoring and for which
jnxoptIfODUkTtpPresent is false(2) and
(i) jnxoptIfODUkDirectionality has the value bidirectional(3), or
(ii) jnxoptIfODUkDirectionality has the value sink(1) and
jnxoptIfODUkTCodirectional has the value true(1), or
(iii) jnxoptIfODUkDirectionality has the value source(3) and
jnxoptIfODUkTCodirectional has the value false(2).
It may be implemented only if the jnxoptIfODUkGroup and
jnxoptIfODUkTSinkGroup are also implemented."
GROUP jnxoptIfODUkTNimGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support non-intrusive
tandem connection monitoring. It may be implemented
only if the jnxoptIfODUkGroup is also implemented."
::= { jnxoptIfCompl 1 }
jnxoptIfPreOtnPMCompl MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Implementation requirements for Pre-OTN performance
monitoring functions defined in this MIB module."
MODULE -- this module
MANDATORY-GROUPS {
jnxoptIfPerfMonGroup
}
GROUP jnxoptIfOTSnSinkPreOtnPMGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(196) that support OTSn sink
functions (i.e., for which the corresponding instance
of jnxoptIfOTSnDirectionality -- if implemented -- has
the value sink(1) or bidirectional(3))."
GROUP jnxoptIfOTSnSinkPreOtnPMThresholdGroup
DESCRIPTION
"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
jnxoptIfOTSnSinkPreOtnPMGroup is a prerequisite for
implementing this group."
GROUP jnxoptIfOTSnSourcePreOtnPMGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalTransport(196) that support OTSn source
functions (i.e., for which the corresponding instance
of jnxoptIfOTSnDirectionality -- if implemented -- has
the value source(2) or bidirectional(3))."
GROUP jnxoptIfOTSnSourcePreOtnPMThresholdGroup
DESCRIPTION
"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
jnxoptIfOTSnSourcePreOtnPMGroup is a prerequisite for
implementing this group "
GROUP jnxoptIfOMSnSinkPreOtnPMGroup
DESCRIPTION
"This group is optional. It may be implemented by systems
with the necessary instrumentation on interfaces of ifType
opticalTransport(196) that support OMSn sink functions
(i.e., for which the corresponding instance of
jnxoptIfOMSnDirectionality -- if implemented -- has the value
sink(1) or bidirectional(3))."
GROUP jnxoptIfOMSnSinkPreOtnPMThresholdGroup
DESCRIPTION
"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
jnxoptIfOMSnSinkPreOtnPMGroup is a prerequisite for
implementing this group "
GROUP jnxoptIfOMSnSourcePreOtnPMGroup
DESCRIPTION
"This group is optional. It may be implemented by systems
with the necessary instrumentation on interfaces of ifType
opticalTransport(196) that support OMSn source functions
(i.e., for which the corresponding instance of
jnxoptIfOMSnDirectionality -- if implemented -- has the value
source(2) or bidirectional(3))."
GROUP jnxoptIfOMSnSourcePreOtnPMThresholdGroup
DESCRIPTION
"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
jnxoptIfOMSnSourcePreOtnPMGroup is a prerequisite for
implementing this group "
GROUP jnxoptIfOChGroupSinkPreOtnPMGroup
DESCRIPTION
"This group is optional. It may be implemented by systems
with the necessary instrumentation on interfaces of ifType
opticalChannelGroup(219) that support OChGroup sink functions
(i.e., for which the corresponding instance of
jnxoptIfOChGroupDirectionality -- if implemented -- has the value
sink(1) or bidirectional(3))."
GROUP jnxoptIfOChGroupSinkPreOtnPMThresholdGroup
DESCRIPTION
"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
jnxoptIfOChGroupSinkPreOtnPMGroup is a prerequisite for
implementing this group "
GROUP jnxoptIfOChGroupSourcePreOtnPMGroup
DESCRIPTION
"This group is optional. It may be implemented by systems
with the necessary instrumentation on interfaces of ifType
opticalChannelGroup(219) that support OChGroup source functions
(i.e., for which the corresponding instance of
jnxoptIfOChGroupDirectionality -- if implemented -- has the value
source(2) or bidirectional(3))."
GROUP jnxoptIfOChGroupSourcePreOtnPMThresholdGroup
DESCRIPTION
"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
jnxoptIfOChGroupSourcePreOtnPMGroup is a prerequisite for
implementing this group "
GROUP jnxoptIfOChSinkPreOtnPMGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OCh sink functions
(i.e., for which the corresponding instance of
jnxoptIfOChDirectionality -- if implemented -- has the
value sink(1) or bidirectional(3))."
GROUP jnxoptIfOChSinkPreOtnPMThresholdGroup
DESCRIPTION
"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
jnxoptIfOChSinkPreOtnPMGroup is a prerequisite for
implementing this group "
GROUP jnxoptIfOChSourcePreOtnPMGroup
DESCRIPTION
"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OCh source functions
(i.e., for which the corresponding instance of
jnxoptIfOChDirectionality -- if implemented -- has the
value source(2) or bidirectional(3))."
GROUP jnxoptIfOChSourcePreOtnPMThresholdGroup
DESCRIPTION
"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
jnxoptIfOChSourcePreOtnPMGroup is a prerequisite for
implementing this group "
::= { jnxoptIfCompl 2 }
END