mibs/junos/JUNIPER-PW-ATM-MIB
-- extracted from pw-atm-draft-06
JUNIPER-PW-ATM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Counter32, Counter64, Unsigned32, mib-2
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
TruthValue, RowStatus, RowPointer
FROM SNMPv2-TC
PerfCurrentCount, PerfIntervalCount
FROM PerfHist-TC-MIB
-- Juniper Specific ATM MIB
jnxMibs
FROM JUNIPER-SMI -- *** JNX ***
jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex
FROM JUNIPER-VPN-MIB
InterfaceIndex
FROM IF-MIB
AtmVpIdentifier, AtmVcIdentifier
FROM ATM-TC-MIB;
jnxPWAtmMIB MODULE-IDENTITY
LAST-UPDATED "200909010000Z" -- 2008
ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3)
Working Group"
CONTACT-INFO
"Juniper Technical Assistance Center
Juniper Networks, Inc.
1133 Innovation Way
Sunnyvale, CA 94089
E-mail: support@juniper.net"
DESCRIPTION
"This MIB module defines objects used for managing
the atm pseudowires in Juniper products."
-- Revision history.
REVISION "200909010000Z" -- 2008
DESCRIPTION " This mib is a modified version of RFC 5605"
::= { jnxMibs 57}
jnxpwAtmNotifications OBJECT IDENTIFIER ::= { jnxPWAtmMIB 0 }
jnxpwAtmObjects OBJECT IDENTIFIER ::= { jnxPWAtmMIB 1 }
jnxpwAtmConformance OBJECT IDENTIFIER ::= { jnxPWAtmMIB 2 }
--Generic ATM PW table for all types of ATM PW connection.
jnxpwAtmCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwAtmCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies generic information for an ATM PW
to be carried over PSN in any mode."
::= { jnxpwAtmObjects 1 }
jnxpwAtmCfgEntry OBJECT-TYPE
SYNTAX JnxPwAtmCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains a set of parameters for
the ATM PW that needs to be adapted and carried
over PSN. This table is indexed by pwIndex from
pwTable. An entry is created for every newly ATM
type associated pwIndex in the pwTable. Unless
otherwise specified, all read-write objects in
this table MAY be changed when the PW is defined
as not active and all RW objects values must
persist after reboot"
REFERENCE
"See [PWMIB] "
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex }
::= { jnxpwAtmCfgTable 1 }
JnxPwAtmCfgEntry ::= SEQUENCE {
jnxpwAtmCfgMaxCellConcatenation Unsigned32,
jnxpwAtmCfgFarEndMaxCellConcatenation Unsigned32,
jnxpwAtmCfgTimeoutMode INTEGER,
jnxpwAtmClpQosMapping TruthValue
}
jnxpwAtmCfgMaxCellConcatenation OBJECT-TYPE
SYNTAX Unsigned32 (1..29)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of ATM cells that can be
concatenated into one PW packet towards PSN.
In non LDP or other signaling protocol environment,
this object MAY be changed at anytime, but traffic
might be interuppted, otherwise, it may be changed
when PW is not active."
::= { jnxpwAtmCfgEntry 1 }
jnxpwAtmCfgFarEndMaxCellConcatenation OBJECT-TYPE
SYNTAX Unsigned32 (1..29)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of ATM cells that can be
concatenated into one PW packet towards PSN as reported by
the far end. If no LDP in use, the object will either
return value 0 or allow setting it for calculating
protocol overhead."
::= { jnxpwAtmCfgEntry 2 }
jnxpwAtmCfgTimeoutMode OBJECT-TYPE
SYNTAX INTEGER
{
notApplicable (1),
disabled (2),
enabled (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This objects determines whether a packet can be
transmitted to the PSN based on time out expiration
for collecting cells or not. The actual handling of the
time out is implementation specific-as such this object
may be changed at any time under proper consideration of
traffic interupption effect."
::= { jnxpwAtmCfgEntry 3 }
jnxpwAtmClpQosMapping OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This Object indicates whether the CLP bits should be
considered when setting the value in the Quality
of Service fields of the encapsulating protocol
(e.g. EXP fields of the MPLS Label Stack). Selecting
True allows the drop precedence to be preserved
across the PSN. In transparent cell transport,
the value of this object MUST be false(2), in other
cases it can be changed at any time."
REFERENCE
"See [ATMENCAP] section 12"
::= { jnxpwAtmCfgEntry 4 }
-- Device capable of implementing N:1, 1:1 and transparent cell
-- mode assumes to support the N:1 table for all
-- modes with respective applicable setting.
-- In such implementation, user can create an entry for either
-- 1:1 or transparent cell transport modes only
-- in pwAtmInboundNto1Table. The side effect of such
-- will be an automatic create of the respective line in the
-- pwAtmOutboundNto1Table.
-- ATM PW Outbound Table for N to 1 connection
jnxpwAtmOutboundNto1Table OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwAtmOutboundNto1Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the information for an ATM PW to
be carried over PSN in the outbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following: atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3).
"
::= { jnxpwAtmObjects 2 }
jnxpwAtmOutboundNto1Entry OBJECT-TYPE
SYNTAX JnxPwAtmOutboundNto1Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFFF
during set operation.
Unless otherwise specified, all read-create objects in this
table MUST NOT be changed after row activation
and SHOULD remain unchanged after reboot."
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex }
::= { jnxpwAtmOutboundNto1Table 1 }
JnxPwAtmOutboundNto1Entry ::= SEQUENCE {
jnxpwAtmOutboundNto1AtmIf InterfaceIndex,
jnxpwAtmOutboundNto1Vpi AtmVpIdentifier,
jnxpwAtmOutboundNto1Vci AtmVcIdentifier,
jnxpwAtmOutboundNto1RowStatus RowStatus,
jnxpwAtmOutboundNto1TrafficParamDescr RowPointer,
jnxpwAtmOutboundNto1MappedVpi AtmVpIdentifier,
jnxpwAtmOutboundNto1MappedVci AtmVcIdentifier
}
jnxpwAtmOutboundNto1AtmIf OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ATM Interface that receives cells from the ATM network."
::= { jnxpwAtmOutboundNto1Entry 1 }
jnxpwAtmOutboundNto1Vpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"VPI value of this ATM PW. In atmTransparent(3),
Vpi will be the equivalent of 0xFFFF"
::= { jnxpwAtmOutboundNto1Entry 2 }
jnxpwAtmOutboundNto1Vci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"VCI value of this ATM PW. In atmTransparent(3), or
VP case, the value will be the equivalent of
0xFFFF"
::= { jnxpwAtmOutboundNto1Entry 3 }
jnxpwAtmOutboundNto1RowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This Object is used to create, modify or delete a row in
this table."
::= { jnxpwAtmOutboundNto1Entry 4 }
jnxpwAtmOutboundNto1TrafficParamDescr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents a pointer to a ATM traffic parameter
specific row in either private or standard table which will
be employed while receiving cells from the ATM network.
This table should contain a set
of self-consistent ATM traffic parameters including the ATM
traffic service category. A value of 0.0 indicates Best
Effort."
::= { jnxpwAtmOutboundNto1Entry 5 }
jnxpwAtmOutboundNto1MappedVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The egress generated VPI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13). In other types, the value will be the
equivalent of 0xFFFF. Value MAY be changed when the
PW is defined as not active "
::= { jnxpwAtmOutboundNto1Entry 6 }
jnxpwAtmOutboundNto1MappedVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The egress generated VCI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13. In VP case or other types, the
value will be the equivalent of 0xFFFF.
Value MAY be changed when the PW is defined
as not active."
::= { jnxpwAtmOutboundNto1Entry 7 }
-- ATM PW Inbound Table for N to 1 connection
jnxpwAtmInboundNto1Table OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwAtmInboundNto1Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the information for an ATM PW to
be carried over PSN in the Inbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following:atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3)."
::= { jnxpwAtmObjects 3 }
jnxpwAtmInboundNto1Entry OBJECT-TYPE
SYNTAX JnxPwAtmInboundNto1Entry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFFF
during set operation.
Unless otherwise specified, all Read-Creat objects in this
table MUST NOT be changed after row activation
and SHOULD remain unchanged after reboot."
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex }
::= { jnxpwAtmInboundNto1Table 1 }
JnxPwAtmInboundNto1Entry ::= SEQUENCE {
jnxpwAtmInboundNto1AtmIf InterfaceIndex,
jnxpwAtmInboundNto1Vpi AtmVpIdentifier,
jnxpwAtmInboundNto1Vci AtmVcIdentifier,
jnxpwAtmInboundNto1RowStatus RowStatus,
jnxpwAtmInboundNto1TrafficParamDescr RowPointer,
jnxpwAtmInboundNto1MappedVpi AtmVpIdentifier,
jnxpwAtmInboundNto1MappedVci AtmVcIdentifier
}
jnxpwAtmInboundNto1AtmIf OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ATM Interface that receives cells from the ATM network."
::= { jnxpwAtmInboundNto1Entry 1 }
jnxpwAtmInboundNto1Vpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"VPI value of this ATM PW. In atmTransparent(3),
Vpi will be the equivalent of 0xFFFF."
::= { jnxpwAtmInboundNto1Entry 2 }
jnxpwAtmInboundNto1Vci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"VCI value of this ATM PW. In atmTransparent(3), or
VP case, the value will be the equivalent of
0xFFFF"
::= { jnxpwAtmInboundNto1Entry 3 }
jnxpwAtmInboundNto1RowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This Object is used to create, modify or delete a row in
this table."
::= { jnxpwAtmInboundNto1Entry 4 }
jnxpwAtmInboundNto1TrafficParamDescr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents a pointer to a ATM traffic parameter
specific row in either private or standard table which will
be employed while receiving cells from the ATM network.
This table should contain a set
of self-consistent ATM traffic parameters including the ATM
traffic service category. A value of 0.0 indicates Best
Effort."
::= { jnxpwAtmInboundNto1Entry 5 }
jnxpwAtmInboundNto1MappedVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The generated VPI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13). In other types, the value will be the
equivalent of 0xFFFF. Value MAY be changed when the
PW is defined as not active."
::= { jnxpwAtmInboundNto1Entry 6 }
jnxpwAtmInboundNto1MappedVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The generated VCI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13. In VP case or other types, the
value will be the equivalent of 0xFFFF.
Value MAY be changed when the
PW is defined as not active."
::= { jnxpwAtmInboundNto1Entry 7 }
-- ATM PW Outbound Perf Table
-- The following supplement the counters presented in the
-- PW generic MIB
-- ATM PW Performance Current Table.
jnxpwAtmPerfCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwAtmPerfCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The current 15 minute interval counts are in
this table.
This table provides performance information per ATM PW."
::= { jnxpwAtmObjects 4 }
jnxpwAtmPerfCurrentEntry OBJECT-TYPE
SYNTAX JnxPwAtmPerfCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for every
pwAtmCfgTable entry. After 15 minutes, the contents of this
table entry are copied to a new entry in the
pwAtmPerfInterval table and the counts in this entry
are reset to zero."
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex }
::= { jnxpwAtmPerfCurrentTable 1 }
JnxPwAtmPerfCurrentEntry ::= SEQUENCE {
jnxpwAtmPerfCurrentMissingPkts PerfCurrentCount,
jnxpwAtmPerfCurrentPktsReOrder PerfCurrentCount,
jnxpwAtmPerfCurrentPktsMisOrder PerfCurrentCount,
jnxpwAtmPerfCurrentPktsTimeout PerfCurrentCount,
jnxpwAtmPerfCurrentPktsXmit Counter64,
jnxpwAtmPerfCurrentCellsDropped PerfCurrentCount,
jnxpwAtmPerfCurrentPktsReceived Counter64,
jnxpwAtmPerfCurrentUnknownCells Counter64
}
jnxpwAtmPerfCurrentMissingPkts OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control word
sequence number gaps)."
::= { jnxpwAtmPerfCurrentEntry 1 }
jnxpwAtmPerfCurrentPktsReOrder OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this Feature."
::= { jnxpwAtmPerfCurrentEntry 2 }
jnxpwAtmPerfCurrentPktsMisOrder OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order (via control word
sequence numbers)."
::= { jnxpwAtmPerfCurrentEntry 3 }
jnxpwAtmPerfCurrentPktsTimeout OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets transmitted due to timeout expiration
while attempting to collect cells."
::= { jnxpwAtmPerfCurrentEntry 4 }
jnxpwAtmPerfCurrentPktsXmit OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of transmitted packets."
::= { jnxpwAtmPerfCurrentEntry 5 }
jnxpwAtmPerfCurrentCellsDropped OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of dropped cells."
::= { jnxpwAtmPerfCurrentEntry 6 }
jnxpwAtmPerfCurrentPktsReceived OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of received packets."
::= { jnxpwAtmPerfCurrentEntry 7 }
jnxpwAtmPerfCurrentUnknownCells OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of cells received from the PSN with unknown VPI or
VCI values. This object is relevant only in N:1 mode."
::= { jnxpwAtmPerfCurrentEntry 8 }
-- End ATM PW Performance Current Interval Table
-- ATM PW Performance Interval Table.
jnxpwAtmPerfIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwAtmPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides performance information per ATM PW
similar to the pwAtmPerfCurrentTable above. However,
these counts represent historical 15 minute intervals.
Typically, this table will have a maximum of 96 entries
for a 24 hour period. "
::= { jnxpwAtmObjects 5 }
jnxpwAtmPerfIntervalEntry OBJECT-TYPE
SYNTAX JnxPwAtmPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for
every pwAtmPerfCurrentEntry that is 15 minutes old.
The contents of the Current entry are copied to the new
entry here. The Current entry, then resets its counts
to zero for the next current 15 minute interval. "
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex, jnxpwAtmPerfIntervalNumber }
::= { jnxpwAtmPerfIntervalTable 1 }
JnxPwAtmPerfIntervalEntry ::= SEQUENCE {
jnxpwAtmPerfIntervalNumber Unsigned32,
jnxpwAtmPerfIntervalValidData TruthValue,
jnxpwAtmPerfIntervalDuration Unsigned32,
jnxpwAtmPerfIntervalMissingPkts PerfIntervalCount,
jnxpwAtmPerfIntervalPktsReOrder PerfIntervalCount,
jnxpwAtmPerfIntervalPktsMisOrder PerfIntervalCount,
jnxpwAtmPerfIntervalPktsTimeout PerfIntervalCount,
jnxpwAtmPerfIntervalPktsXmit Counter64,
jnxpwAtmPerfIntervalCellsDropped PerfIntervalCount,
jnxpwAtmPerfIntervalPktsReceived Counter64,
jnxpwAtmPerfIntervalUnknownCells Counter64
}
jnxpwAtmPerfIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number (normally between 1 and 96 to cover a 24 hour
period) which identifies the interval for which the set
of statistics is available. The interval identified by 1
is the most recently completed 15 minute interval, and
the interval identified by N is the interval immediately
preceding the one identified by N-1. The minimum range of
N is 1 through 4. The default range is 1 through 32. The
maximum value of N is 96."
::= { jnxpwAtmPerfIntervalEntry 1 }
jnxpwAtmPerfIntervalValidData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval
is valid."
::= { jnxpwAtmPerfIntervalEntry 2 }
jnxpwAtmPerfIntervalDuration OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided."
::= { jnxpwAtmPerfIntervalEntry 3 }
jnxpwAtmPerfIntervalMissingPkts OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control
word sequence number gaps)."
::= { jnxpwAtmPerfIntervalEntry 4 }
jnxpwAtmPerfIntervalPktsReOrder OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
Feature."
::= { jnxpwAtmPerfIntervalEntry 5 }
jnxpwAtmPerfIntervalPktsMisOrder OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order (via control word
sequence numbers)."
::= { jnxpwAtmPerfIntervalEntry 6 }
jnxpwAtmPerfIntervalPktsTimeout OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets transmitted due to timeout expiration."
::= { jnxpwAtmPerfIntervalEntry 7 }
jnxpwAtmPerfIntervalPktsXmit OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of transmitted packets."
::= { jnxpwAtmPerfIntervalEntry 8 }
jnxpwAtmPerfIntervalCellsDropped OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of dropped cells."
::= { jnxpwAtmPerfIntervalEntry 9 }
jnxpwAtmPerfIntervalPktsReceived OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of received packets."
::= { jnxpwAtmPerfIntervalEntry 10 }
jnxpwAtmPerfIntervalUnknownCells OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of cells received from the PSN with unknown VPI or
VCI values. This object is relevant only in N:1 mode."
::= { jnxpwAtmPerfIntervalEntry 11 }
-- End ATM PW Performance Interval Table
-- ATM PW 1day Performance Table
jnxpwAtmPerf1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwAtmPerf1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides performance information per ATM PW
similar to the pwAtmPerfIntervalTable above. However,
these counters represent historical 1 day intervals up to
one full month."
::= { jnxpwAtmObjects 6 }
jnxpwAtmPerf1DayIntervalEntry OBJECT-TYPE
SYNTAX JnxPwAtmPerf1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry is created in this table by the agent
for every entry in the pwAtmCfgTable table."
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex, jnxpwAtmPerf1DayIntervalNumber }
::= { jnxpwAtmPerf1DayIntervalTable 1 }
JnxPwAtmPerf1DayIntervalEntry ::= SEQUENCE {
jnxpwAtmPerf1DayIntervalNumber Unsigned32,
jnxpwAtmPerf1DayIntervalValidData TruthValue,
jnxpwAtmPerf1DayIntervalDuration Unsigned32,
jnxpwAtmPerf1DayIntervalMissingPkts Counter32,
jnxpwAtmPerf1DayIntervalPktsReOrder Counter32,
jnxpwAtmPerf1DayIntervalPktsMisOrder Counter32,
jnxpwAtmPerf1DayIntervalPktsTimeout Counter32,
jnxpwAtmPerf1DayIntervalPktsXmit Counter64,
jnxpwAtmPerf1DayIntervalCellsDropped Counter32,
jnxpwAtmPerf1DayIntervalPktsReceived Counter64,
jnxpwAtmPerf1DayIntervalUnknownCells Counter64
}
jnxpwAtmPerf1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..365)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The number of interval, where 1 indicates current day
measured period and 2 and above indicate previous days
respectively"
::= { jnxpwAtmPerf1DayIntervalEntry 1 }
jnxpwAtmPerf1DayIntervalValidData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates if the data for this interval
is valid."
::= { jnxpwAtmPerf1DayIntervalEntry 2 }
jnxpwAtmPerf1DayIntervalDuration OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided."
::= { jnxpwAtmPerf1DayIntervalEntry 3 }
jnxpwAtmPerf1DayIntervalMissingPkts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control word
sequence number gaps)."
::= { jnxpwAtmPerf1DayIntervalEntry 4 }
jnxpwAtmPerf1DayIntervalPktsReOrder OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
feature."
::= { jnxpwAtmPerf1DayIntervalEntry 5 }
jnxpwAtmPerf1DayIntervalPktsMisOrder OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered."
::= { jnxpwAtmPerf1DayIntervalEntry 6 }
jnxpwAtmPerf1DayIntervalPktsTimeout OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets transmitted due to timeout expiration."
::= { jnxpwAtmPerf1DayIntervalEntry 7 }
jnxpwAtmPerf1DayIntervalPktsXmit OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of transmitted packets."
::= { jnxpwAtmPerf1DayIntervalEntry 8 }
jnxpwAtmPerf1DayIntervalCellsDropped OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of dropped cells."
::= { jnxpwAtmPerf1DayIntervalEntry 9 }
jnxpwAtmPerf1DayIntervalPktsReceived OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of received packets."
::= { jnxpwAtmPerf1DayIntervalEntry 10 }
jnxpwAtmPerf1DayIntervalUnknownCells OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of cells received from the PSN with unknown VPI
or VCI value. This object is relevant only in N:1 mode."
::= { jnxpwAtmPerf1DayIntervalEntry 11 }
-- End of ATM PW Performance table
END