mibs/junos/JUNIPER-PW-TDM-MIB
-- extracted from pw-tdm-draft-08
JUNIPER-PW-TDM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Integer32, Counter32, Unsigned32, transmission
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType,
TimeStamp
FROM SNMPv2-TC
InterfaceIndexOrZero
FROM IF-MIB -- [IFMIB]
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- [RFC3411]
PerfCurrentCount, PerfIntervalCount
FROM PerfHist-TC-MIB
-- Juniper Specific TDM MIB
jnxMibs
FROM JUNIPER-SMI -- *** JNX ***
jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex
FROM JUNIPER-VPN-MIB
jnxPwTdmMibRoot
FROM JUNIPER-SMI;
jnxPWTdmMIB MODULE-IDENTITY
LAST-UPDATED "200704030000Z"
ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3)
Working Group"
CONTACT-INFO
" Orly Nicklass
Postal: RAD Data Communications
24 Raoul Wallenberg St., Bldg C
Tel Aviv 69719, Israel
Email: orly_n@rad.com
The PWE3 Working Group (email distribution pwe3@ietf.org,
http://www.ietf.org/html.charters/pwe3-charter.html)
"
DESCRIPTION
"This MIB contains managed object definitions for
encapsulating TDM (T1,E1, T3, E3, NxDS0) as
pseudo-wires over packet-switching networks (PSN).
This MIB supplements the PW-STD-MIB as in: Zelig, D.,
Nadeau,T. 'Pseudo Wire (PW) Management Information Base'.
The PW-STD-MIB contains structures and MIB associations
generic to Pseudo-Wire (PW) emulation. PW-specific
MIBs (such as this) contain config and stats for specific
PW types.
Copyright (C) The IETF Trust (2007). This version
of this MIB module is part of RFC yyyy; see the RFC
itself for full legal notices.
-- RFC Ed.: replace yyyy with actual RFC number & remove this
note"
REVISION "200704030000Z" -- April 2007
DESCRIPTION
"Initial version published as part of RFC YYYY."
-- RFC Editor: please replace YYYY with IANA assigned value, and
-- delete this note.
::= {jnxPwTdmMibRoot 1} --** JNX **
-- Local Textual conventions
JnxPwTDMCfgIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Index into the relevant pwXXXCfgTable."
SYNTAX Unsigned32 (1..4294967295)
JnxPwCfgIndexOrzero ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"Index in any of the relevant configuration tables for
supplement information regarding configuration of the
specific technology. Value 0 implies no additional
configuration information is applicable."
SYNTAX Unsigned32 (0..4294967295)
-- Tables, Scalars
jnxpwTDMObjects OBJECT IDENTIFIER ::= { jnxPWTdmMIB 1 }
-- Notifications
jnxpwTDMNotifications OBJECT IDENTIFIER ::= { jnxPWTdmMIB 2 }
-- Conformance
jnxpwTDMConformance OBJECT IDENTIFIER ::= { jnxPWTdmMIB 3 }
-- TDM PW table
jnxpwTDMTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwTDMEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains basic information including ifIndex,
and pointers to entries in the relevant TDM config
tables for this TDM PW."
::= { jnxpwTDMObjects 1 }
jnxpwTDMEntry OBJECT-TYPE
SYNTAX JnxPwTDMEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is indexed by the same index that was
created for the associated entry in the PW Table
(in the PW-STD-MIB).
- The PwIndex.
An entry is created in this table by the agent for every
entry in the pwTable with a pwType equal to one of the
following:
e1Satop(17), t1Satop(18), e3Satop(19), t3Satop(20),
basicCesPsn(21), basicTdmIp(22), tdmCasCesPsn(23),
tdmCasTdmIp(24).
Unless otherwise specified, all RW objects in this table
MUST NOT be changed after row activation (see [PWMIB])
and should remain unchanged after reboot."
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex }
::= { jnxpwTDMTable 1 }
JnxPwTDMEntry ::= SEQUENCE {
jnxpwTDMRate Integer32,
jnxpwTDMIfIndex InterfaceIndexOrZero,
jnxpwGenTDMCfgIndex JnxPwCfgIndexOrzero,
jnxpwRelTDMCfgIndex JnxPwCfgIndexOrzero,
jnxpwTDMConfigError BITS,
jnxpwTDMTimeElapsed Integer32,
jnxpwTDMValidIntervals Integer32,
jnxpwTDMValidDayIntervals Integer32,
jnxpwTDMLastEsTimeStamp TimeStamp
}
jnxpwTDMRate OBJECT-TYPE
SYNTAX Integer32
-- MAX-ACCESS read-write
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The parameter represents the bit-rate of the TDM service
in multiples of the 'basic' 64 Kbit/s rate [TDMCP-EXT].
It complements the definition of pwType used in
PW-STD-MIB.
For structure-agnostic the following should be used:
a) Satop E1 - 32
b) Satop T1 emulation:
i) MUST be set to 24 in the basic emulation mode
ii) MUST be set to 25 for the 'Octet-aligned T1'
emulation mode
c) Satop E3 - 535
d) Satop T3 - 699
For all kinds of structure-aware emulation, this parameter
MUST be set to N where N is the number of DS0 channels
in the corresponding attachment circuit."
REFERENCE
"TDMCP-EXT"
DEFVAL { 32 }
::= { jnxpwTDMEntry 1 }
jnxpwTDMIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
-- MAX-ACCESS read-write
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is a unique index within the ifTable. It represents
the interface index of the full link or the interface
index for the bundle holding the group of
time slots to be transmitted via this PW connection.
A value of zero indicates an interface index that has yet
to be determined.
Once set, if the TDM ifIndex is (for some reason) later
removed, the agent SHOULD delete the associated PW rows
(e.g., this pwTDMTable entry). If the agent does not
delete the rows, the agent MUST set this object to
zero."
::= { jnxpwTDMEntry 2 }
jnxpwGenTDMCfgIndex OBJECT-TYPE
SYNTAX JnxPwCfgIndexOrzero
-- MAX-ACCESS read-write
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index to the generic parameters in the TDM configuration
table that appears in this MIB module. It is likely that
multiple TDM PWs of the same characteristic will share
a single TDM Cfg entry."
::= { jnxpwTDMEntry 3 }
jnxpwRelTDMCfgIndex OBJECT-TYPE
SYNTAX JnxPwCfgIndexOrzero
-- MAX-ACCESS read-write
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index to the relevant TDM configuration table entry
that appears in one of the related MIB modules
such as TDMoIP or CESoPSN. It is likely that
multiple TDM PWs of the same characteristic will share
a single configuration entry of the relevant type.
The value 0 implies no entry in other related MIB"
::= { jnxpwTDMEntry 4 }
jnxpwTDMConfigError OBJECT-TYPE
SYNTAX BITS {
notApplicable ( 0),
tdmTypeIncompatible ( 1),
peerRtpIncompatible ( 2),
peerPayloadSizeIncompatible ( 3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Any of the bits are set if the local configuration is
not compatible with the peer configuration as available
from the various parameters options. Setting is done based
on signaling, or else value (0) will be set.
-tdmTypeIncompatible bit is set if the local configuration
is not carrying the same TDM type as the peer configuration.
-peerRtpIncompatible bit is set if the local configuration
is configured to send RTP packets for this PW, and the
remote is not capable of accepting RTP packets.
-peerPayloadSizeIncompatible bit is set if the local
configuration is not carrying the same Payload Size as the
peer configuration. "
::= { jnxpwTDMEntry 5}
jnxpwTDMTimeElapsed OBJECT-TYPE
SYNTAX Integer32 (1..900)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds, including partial seconds,
that have elapsed since the beginning of the current
measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the
current interval exceeds the maximum value, the
agent will return the maximum value."
::= { jnxpwTDMEntry 6}
jnxpwTDMValidIntervals OBJECT-TYPE
SYNTAX Integer32 (0..96)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of previous 15-minute intervals for which data
was collected.
An agent with TDM capability must be capable of supporting
at least n intervals. The minimum value of n is 4, The
default of n is 32 and the maximum value of n is 96.
The value will be n unless the measurement was (re-)
started within the last (n*15) minutes, in which case
the value will be the number of complete 15 minute
intervals for which the agent has at least some data.
In certain cases(e.g., in the case where the agent is
a proxy) it is possible that some intervals are unavailable.
In this case, this interval is the maximum interval number
for which data is available. "
::= { jnxpwTDMEntry 7}
jnxpwTDMValidDayIntervals OBJECT-TYPE
SYNTAX Integer32 (0..30)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of previous days for which data
was collected.
An agent with TDM capability must be capable of supporting
at least n intervals. The minimum value of n is 1, The
default of n is 1 and the maximum value of n is 30."
::= { jnxpwTDMEntry 8}
jnxpwTDMLastEsTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the most recent occasion at
which the TDM PW entered the ES or SES state."
::= { jnxpwTDMEntry 11}
-- End of TDM PW table
-- PW Generic TDM PW Configuration Table
jnxpwTDMCfgIndexNext OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value to be used for
pwTDMCfgIndex when creating entries in the
pwTDMCfgTable. The value 0 indicates that no
unassigned entries are available. To obtain the
value of pwTDMCfgIndexNext for a new entry in the
pwTDMCfgTable, the manager issues a management
protocol retrieval operation. The agent will
determine through its local policy when this
index value will be made available for reuse."
::= { jnxpwTDMObjects 2 }
jnxpwTDMCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwTDMCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains a set of parameters that may be
referenced by one or more TDM PWs in pwTDMTable."
::= { jnxpwTDMObjects 3 }
jnxpwTDMCfgEntry OBJECT-TYPE
SYNTAX JnxPwTDMCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"These parameters define the characteristics of a
TDM PW. They are grouped here to ease NMS burden.
Once an entry is created here it may be re-used
by many PWs.
Unless otherwise specified, all objects in this table
MUST NOT be changed after row activation (see [PWMIB])
if the row index is in used by an entry in pwTDMTable.
Rows should remain unchanged after reboot."
--INDEX { jnxpwTDMCfgIndex }
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex }
::= { jnxpwTDMCfgTable 1 }
JnxPwTDMCfgEntry ::= SEQUENCE {
jnxpwTDMCfgIndex JnxPwTDMCfgIndex,
jnxpwTDMCfgRowStatus RowStatus,
jnxpwTDMCfgPayloadSize Unsigned32,
jnxpwTDMCfgPktReorder TruthValue,
jnxpwTDMCfgRtpHdrUsed TruthValue,
jnxpwTDMCfgJtrBfrDepth Unsigned32,
jnxpwTDMCfgPayloadSuppression INTEGER,
jnxpwTDMCfgConsecPktsInSynch Unsigned32,
jnxpwTDMCfgConsecMissPktsOutSynch Unsigned32,
jnxpwTDMCfgSetUp2SynchTimeOut Unsigned32,
jnxpwTDMCfgPktReplacePolicy INTEGER,
jnxpwTDMCfgAvePktLossTimeWindow Integer32,
jnxpwTDMCfgExcessivePktLossThreshold Unsigned32,
jnxpwTDMCfgAlarmThreshold Unsigned32,
jnxpwTDMCfgClearAlarmThreshold Unsigned32,
jnxpwTDMCfgMissingPktsToSes Unsigned32,
jnxpwTDMCfgTimestampMode INTEGER,
jnxpwTDMCfgStorageType StorageType,
jnxpwTDMCfgPktFiller Unsigned32,
jnxpwTDMCfgName SnmpAdminString
}
jnxpwTDMCfgIndex OBJECT-TYPE
SYNTAX JnxPwTDMCfgIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index to an entry in this table. The value is a copy of the
assigned pwTDMCfgIndexNext"
::= { jnxpwTDMCfgEntry 1 }
jnxpwTDMCfgRowStatus OBJECT-TYPE
SYNTAX RowStatus
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Object used for creating, modifying, and deleting
a row from this table. The following objects should not be
modified if the entry is in used and the status is active:
pwTDMCfgPayloadSize, pwTDMCfgRtpHdrUsed,
pwTDMCfgJtrBfrDepth, and pwTDMCfgPayloadSuppression.
The row should not be deleted if the entry is in used"
::= { jnxpwTDMCfgEntry 2 }
jnxpwTDMCfgPayloadSize OBJECT-TYPE
SYNTAX Unsigned32
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object indicates the PayLoad Size (in bytes)
to be defined during the PW setUp. Upon TX, implementation
must be capable of carrying that amount of bytes.
Upon RX, when the LEN field is set to 0, the payload of
packet MUST assume this size, and if the actual
packet size is inconsistent with this length,
the packet MUST be considered to be malformed. "
::= { jnxpwTDMCfgEntry 4 }
jnxpwTDMCfgPktReorder OBJECT-TYPE
SYNTAX TruthValue
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If set True: as CE bound packets are queued in the
jitter buffer, out of order packets are re-ordered. The
maximum sequence number differential (i.e., the range in
which re-sequencing can occur) is dependant on the depth
of the jitter buffer. See pwTDMCfgJtrBfrDepth.
NOTE: Some implementations may not support this feature.
The agent is then required to set this to False."
::= { jnxpwTDMCfgEntry 5 }
jnxpwTDMCfgRtpHdrUsed OBJECT-TYPE
SYNTAX TruthValue
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If set to False: an RTP header is not pre-pended to the
TDM packet."
REFERENCE
"SATOP"
DEFVAL { false }
::= { jnxpwTDMCfgEntry 6 }
jnxpwTDMCfgJtrBfrDepth OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microsecond"
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of this buffer SHOULD be locally
configured to allow accommodation to the PSN-specific packet
delay variation.
If configured to a value not supported by the
implementation, the agent MUST return an error code
'jtrBfrDepth' in 'pwTDMConfigError '
NOTE: jitter buffers are a limited resource to
be managed. The actual size should be at least twice as big
as the value of pwTDMCfgJtrBfrDepth "
DEFVAL { 3000 }
::= { jnxpwTDMCfgEntry 7 }
jnxpwTDMCfgPayloadSuppression OBJECT-TYPE
SYNTAX INTEGER
{
enable ( 1),
disable ( 2)
}
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Selecting 'enable' means: Payload suppression is allowed.
Payload MAY be omitted in order to conserve bandwidth.
Selecting 'disable' means: no suppresion under any
condition.
Object MAY be changed at any time."
DEFVAL { disable }
::= { jnxpwTDMCfgEntry 8 }
jnxpwTDMCfgConsecPktsInSynch OBJECT-TYPE
SYNTAX Unsigned32
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of consecutive packets with sequential
sequence numbers that are required to exit the
LOPS state.
Object MAY be changed when the related PW is
defined as not active."
REFERENCE
"SATOP"
DEFVAL { 2 }
::= { jnxpwTDMCfgEntry 9 }
jnxpwTDMCfgConsecMissPktsOutSynch OBJECT-TYPE
SYNTAX Unsigned32
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of consecutive missing packets that are
required to enter the LOPS state.
Object MAY be changed when the related PW is
defined as not active."
REFERENCE
"SATOP"
DEFVAL { 10 }
::= { jnxpwTDMCfgEntry 10 }
jnxpwTDMCfgSetUp2SynchTimeOut OBJECT-TYPE
SYNTAX Unsigned32
UNITS "millisecond"
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time the host should wait before declaring the
pseudo wire in down state, if the number of consecutive
TDM packets that have been received after changing the
adminstrative status to up and after finalization of
signaling (if supported) between the two PEs is smaller
than pwTDMCfgConsecPktsInSynch. Once the the pw has
OperStatus of 'up' this parameter is no longer valid. This
parameter is defined to ensure that the host does not
prematurely inform failure of the pw. In particular pw 'down'
notifications should not be sent before expiration of this
timer. This parameter is valid only after adminisrative
changes of the status of the pw. If the pw fails due to
network impairments a 'down' notification should be sent.
Object MAY be changed when the related PW is
defined as not active."
DEFVAL {5000}
::= { jnxpwTDMCfgEntry 11 }
jnxpwTDMCfgPktReplacePolicy OBJECT-TYPE
SYNTAX INTEGER
{
allOnes (1),
implementationSpecific(2),
filler (3) --user defined
}
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This parameter determines the value to be played when CE bound
packets have over/underflow the jitter buffer, or are missing
for any reason. This byte pattern is sent(played)on
the TDM line. Selecting implementationSpecific(2) implies
agent specific algorithm. Selecting filler(3) requires setting
of pwTDMCfgPktFiller.
Object MAY be changed when the related PW is
defined as not active."
DEFVAL { allOnes } -- Play AIS
::= { jnxpwTDMCfgEntry 12 }
jnxpwTDMCfgAvePktLossTimeWindow OBJECT-TYPE
SYNTAX Integer32
UNITS "millisecond"
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of time over which the average packet
loss rate should be computed to detect Excessive packet
loss rate.
Object MAY be changed when the related PW is
defined as not active."
::= { jnxpwTDMCfgEntry 13}
jnxpwTDMCfgExcessivePktLossThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Percent"
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Excessive packet loss rate is detected by computing the
average packetloss rate over a pwTDMCfgAvePktLossTimeWindow
amount of time and comparing it with this threshold value.
The rate is expressed in precentage.
Object MAY be changed when the related PW is
defined as not active."
::= { jnxpwTDMCfgEntry 14 }
jnxpwTDMCfgAlarmThreshold OBJECT-TYPE
SYNTAX Unsigned32
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Alarms are only reported when the defect state persists
for the length of time specified by this object.
The object's unit is millisec.
Object MAY be changed when the related PW is
defined as not active."
DEFVAL { 2500 }
::= { jnxpwTDMCfgEntry 15 }
jnxpwTDMCfgClearAlarmThreshold OBJECT-TYPE
SYNTAX Unsigned32
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Alarm MUST be cleared after the corresponding defect is
undetected for the amount of time specified by this object.
The object's unit is millisec.
Object MAY be changed when the related PW is
defined as not active."
DEFVAL { 10000 }
::= { jnxpwTDMCfgEntry 16 }
jnxpwTDMCfgMissingPktsToSes OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Percent"
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Percent of missing packets detected (consecutive or not)
within a 1 second window to cause a Severely Error
Second (SES) to be counted.
Object MAY be changed when the related PW is
defined as not active."
DEFVAL { 30 }
::= { jnxpwTDMCfgEntry 17 }
jnxpwTDMCfgTimestampMode OBJECT-TYPE
SYNTAX INTEGER
{
notApplicable (1),
absolute (2),
differential (3)
}
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Timestamp generation MAY be used in one of the following
modes:
1. Absolute mode: the PSN-bound IWF sets timestamps
using the clock recovered from the incoming TDM attachment
circuit. As a consequence, the timestamps are closely
correlated with the sequence numbers. All TDM implementations
that support usage of the RTP header MUST support this mode.
2. Differential mode: Both IWFs have access to a common high-
quality timing source, and this source is used for timestamp
generation. Support of this mode is OPTIONAL.
Object MAY be changed when the related PW is
defined as not active."
::= { jnxpwTDMCfgEntry 18 }
jnxpwTDMCfgStorageType OBJECT-TYPE
SYNTAX StorageType
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the storage type for this
row."
::= { jnxpwTDMCfgEntry 19 }
jnxpwTDMCfgPktFiller OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Filler byte pattern played out on the TDM
interface if pwTDMCfgPktReplacePolicy
was set to filler(3).
Object MAY be changed when the related PW is
defined as not active."
DEFVAL
{ 255 } -- Play all ones, equal to AIS indications.
::= { jnxpwTDMCfgEntry 20 }
jnxpwTDMCfgName OBJECT-TYPE
SYNTAX SnmpAdminString
-- MAX-ACCESS read-create
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A descriptive string, prefereably unique name, to an entry
in this table.
Object MAY be changed at any time."
::= { jnxpwTDMCfgEntry 21 }
-- END of Table
-- The following counters work together to integrate
-- errors and the lack of errors on the TDM PW. An error is
-- caused by a missing packet. Missing packet can be a result
-- of: packet loss in the network, (uncorrectable) packet out
-- of sequence, packet length error, jitter buffer overflow,
-- and jitter buffer underflow. The result is declaring whether
-- or not the TDM PW is in Loss of Packet (LOPS) state.
-- TDM PW Performance Current Table.
jnxpwTDMPerfCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwTDMPerfCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The current 15 minute interval counts are in
this table.
This table provides per TDM PW performance information."
::= { jnxpwTDMObjects 5 }
jnxpwTDMPerfCurrentEntry OBJECT-TYPE
SYNTAX JnxPwTDMPerfCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for every
pwTDMTable entry. After 15 minutes, the contents of this
table entry are copied to a new entry in the
pwTDMPerfInterval table and the counts in this entry
are reset to zero."
-- INDEX { jnxpwIndex }
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex }
::= { jnxpwTDMPerfCurrentTable 1 }
JnxPwTDMPerfCurrentEntry ::= SEQUENCE {
jnxpwTDMPerfCurrentMissingPkts PerfCurrentCount,
jnxpwTDMPerfCurrentPktsReOrder PerfCurrentCount,
jnxpwTDMPerfCurrentJtrBfrUnderruns PerfCurrentCount,
jnxpwTDMPerfCurrentMisOrderDropped PerfCurrentCount,
jnxpwTDMPerfCurrentMalformedPkt PerfCurrentCount,
jnxpwTDMPerfCurrentESs PerfCurrentCount,
jnxpwTDMPerfCurrentSESs PerfCurrentCount,
jnxpwTDMPerfCurrentUASs PerfCurrentCount,
jnxpwTDMPerfCurrentFC PerfCurrentCount
}
jnxpwTDMPerfCurrentMissingPkts OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control word
sequence number gaps)."
::= { jnxpwTDMPerfCurrentEntry 1 }
jnxpwTDMPerfCurrentPktsReOrder OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this Feature."
::= { jnxpwTDMPerfCurrentEntry 2 }
jnxpwTDMPerfCurrentJtrBfrUnderruns OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a packet needed to be played
out and the jitter buffer was empty."
::= { jnxpwTDMPerfCurrentEntry 3 }
jnxpwTDMPerfCurrentMisOrderDropped OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered, or could
not fit in the jitter buffer."
::= { jnxpwTDMPerfCurrentEntry 4 }
jnxpwTDMPerfCurrentMalformedPkt OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected with unexpected size, or
bad headers' stack"
::= { jnxpwTDMPerfCurrentEntry 5 }
jnxpwTDMPerfCurrentESs OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Error
Seconds encountered. Any malformed packet, seq. error, LOPS
and similar are considered as error second"
::= { jnxpwTDMPerfCurrentEntry 6 }
jnxpwTDMPerfCurrentSESs OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Error Seconds encountered. "
::= { jnxpwTDMPerfCurrentEntry 7 }
jnxpwTDMPerfCurrentUASs OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Unavailable Seconds encountered. Any consequtive
ten seconds of SES are counted as one UAS"
::= { jnxpwTDMPerfCurrentEntry 8 }
jnxpwTDMPerfCurrentFC OBJECT-TYPE
SYNTAX PerfCurrentCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"TDM Failure Counts (FC-TDM). The number of TDM failure
events. A failure event begins when the LOPS failure
is declared, and ends when the failure is cleared. A
failure event that begins in one period and ends in
another period is counted only in the period in which
it begins."
::= { jnxpwTDMPerfCurrentEntry 9 }
-- End TDM PW Performance Current Interval Table
-- TDM PW Performance Interval Table.
jnxpwTDMPerfIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwTDMPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides performance information per TDM PW
similar to the pwTDMPerfCurrentTable above. However,
these counts represent historical 15 minute intervals.
Typically, this table will have a maximum of 96 entries
for a 24 hour period, but is not limited to this. "
::= { jnxpwTDMObjects 6 }
jnxpwTDMPerfIntervalEntry OBJECT-TYPE
SYNTAX JnxPwTDMPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the agent for
every pwTDMPerfCurrentEntry that is 15 minutes old.
The contents of the Current entry are copied to the new
entry here. The Current entry, then resets its counts
to zero for the next current 15 minute interval. "
-- INDEX { jnxpwIndex, jnxpwTDMPerfIntervalNumber }
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex , jnxpwTDMPerfIntervalNumber }
::= { jnxpwTDMPerfIntervalTable 1 }
JnxPwTDMPerfIntervalEntry ::= SEQUENCE {
jnxpwTDMPerfIntervalNumber Unsigned32,
jnxpwTDMPerfIntervalValidData TruthValue,
jnxpwTDMPerfIntervalDuration Unsigned32,
jnxpwTDMPerfIntervalMissingPkts PerfIntervalCount,
jnxpwTDMPerfIntervalPktsReOrder PerfIntervalCount,
jnxpwTDMPerfIntervalJtrBfrUnderruns PerfIntervalCount,
jnxpwTDMPerfIntervalMisOrderDropped PerfIntervalCount,
jnxpwTDMPerfIntervalMalformedPkt PerfIntervalCount,
jnxpwTDMPerfIntervalESs PerfIntervalCount,
jnxpwTDMPerfIntervalSESs PerfIntervalCount,
jnxpwTDMPerfIntervalUASs PerfIntervalCount,
jnxpwTDMPerfIntervalFC PerfIntervalCount
}
jnxpwTDMPerfIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number (normally between 1 and 96 to cover a 24 hour
period) which identifies the interval for which the set
of statistics is available. The interval identified by 1
is the most recently completed 15 minute interval, and
the interval identified by N is the interval immediately
preceding the one identified by N-1. The minimum range of
N is 1 through 4. The default range is 1 through 32. The
maximum value of N is 1 through 96."
::= { jnxpwTDMPerfIntervalEntry 1 }
jnxpwTDMPerfIntervalValidData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval
is valid."
::= { jnxpwTDMPerfIntervalEntry 2 }
jnxpwTDMPerfIntervalDuration OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided."
::= { jnxpwTDMPerfIntervalEntry 3 }
jnxpwTDMPerfIntervalMissingPkts OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control
word sequence number gaps)."
::= { jnxpwTDMPerfIntervalEntry 4 }
jnxpwTDMPerfIntervalPktsReOrder OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
Feature."
::= { jnxpwTDMPerfIntervalEntry 5 }
jnxpwTDMPerfIntervalJtrBfrUnderruns OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a packet needed to be played
out and the jitter buffer was empty."
::= { jnxpwTDMPerfIntervalEntry 6 }
jnxpwTDMPerfIntervalMisOrderDropped OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered, or could
not fit in the jitter buffer."
::= { jnxpwTDMPerfIntervalEntry 7 }
jnxpwTDMPerfIntervalMalformedPkt OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected with unexpected size, or
bad headers' stack"
::= { jnxpwTDMPerfIntervalEntry 8 }
jnxpwTDMPerfIntervalESs OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Error
Seconds encountered."
::= { jnxpwTDMPerfIntervalEntry 9 }
jnxpwTDMPerfIntervalSESs OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Error Seconds encountered."
::= { jnxpwTDMPerfIntervalEntry 10 }
jnxpwTDMPerfIntervalUASs OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Unavailable Seconds encountered."
::= { jnxpwTDMPerfIntervalEntry 11 }
jnxpwTDMPerfIntervalFC OBJECT-TYPE
SYNTAX PerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"TDM Failure Counts (FC-TDM). The number of TDM failure
events. A failure event begins when the LOPS failure
is declared, and ends when the failure is cleared. A
failure event that begins in one period and ends in
another period is counted only in the period in which
it begins."
::= { jnxpwTDMPerfIntervalEntry 12 }
-- End TDM PW Performance Interval Table
-- TDM PW 1day Performance Table
jnxpwTDMPerf1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxPwTDMPerf1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides performance information per TDM PW
similar to the pwTDMPerfIntervalTable above. However,
these counters represent historical 1 day intervals up to
one full month. The table consists of real time data, as
such it is not persistence across re-boot."
::= { jnxpwTDMObjects 7 }
jnxpwTDMPerf1DayIntervalEntry OBJECT-TYPE
SYNTAX JnxPwTDMPerf1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry is created in this table by the agent
for every entry in the pwTDMTable table."
INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex, jnxpwTDMPerf1DayIntervalNumber }
::= { jnxpwTDMPerf1DayIntervalTable 1 }
JnxPwTDMPerf1DayIntervalEntry ::= SEQUENCE {
jnxpwTDMPerf1DayIntervalNumber Unsigned32,
jnxpwTDMPerf1DayIntervalValidData TruthValue,
jnxpwTDMPerf1DayIntervalDuration Unsigned32,
jnxpwTDMPerf1DayIntervalMissingPkts Counter32,
jnxpwTDMPerf1DayIntervalPktsReOrder Counter32,
jnxpwTDMPerf1DayIntervalJtrBfrUnderruns Counter32,
jnxpwTDMPerf1DayIntervalMisOrderDropped Counter32,
jnxpwTDMPerf1DayIntervalMalformedPkt Counter32,
jnxpwTDMPerf1DayIntervalESs Counter32,
jnxpwTDMPerf1DayIntervalSESs Counter32,
jnxpwTDMPerf1DayIntervalUASs Counter32,
jnxpwTDMPerf1DayIntervalFC Counter32
}
jnxpwTDMPerf1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The number of interval, where 1 indicates current day
measured period and 2 and above indicate previous days
respectively"
::= { jnxpwTDMPerf1DayIntervalEntry 1 }
jnxpwTDMPerf1DayIntervalValidData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval
is valid."
::= { jnxpwTDMPerf1DayIntervalEntry 2 }
jnxpwTDMPerf1DayIntervalDuration OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided."
::= { jnxpwTDMPerf1DayIntervalEntry 3 }
jnxpwTDMPerf1DayIntervalMissingPkts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of missing packets (as detected via control word
sequence number gaps)."
::= { jnxpwTDMPerf1DayIntervalEntry 4 }
jnxpwTDMPerf1DayIntervalPktsReOrder OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
feature."
::= { jnxpwTDMPerf1DayIntervalEntry 5 }
jnxpwTDMPerf1DayIntervalJtrBfrUnderruns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times a packet needed to be played
out and the jitter buffer was empty."
::= { jnxpwTDMPerf1DayIntervalEntry 6 }
jnxpwTDMPerf1DayIntervalMisOrderDropped OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered, or could
not fit in the jitter buffer."
::= { jnxpwTDMPerf1DayIntervalEntry 7 }
jnxpwTDMPerf1DayIntervalMalformedPkt OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets detected with unexpected size, or
bad headers' stack."
::= { jnxpwTDMPerf1DayIntervalEntry 8 }
jnxpwTDMPerf1DayIntervalESs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Error
Seconds encountered."
::= { jnxpwTDMPerf1DayIntervalEntry 9 }
jnxpwTDMPerf1DayIntervalSESs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Severely
Error Seconds."
::= { jnxpwTDMPerf1DayIntervalEntry 10 }
jnxpwTDMPerf1DayIntervalUASs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
UnAvailable Seconds.
NOTE: When first entering the UAS state, the number
of SES To UAS is added to this object, then as each
additional UAS occurs, this object increments by one."
::= { jnxpwTDMPerf1DayIntervalEntry 11 }
jnxpwTDMPerf1DayIntervalFC OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"TDM Failure Counts (FC-TDM). The number of TDM failure
events. A failure event begins when the LOPS failure
is declared, and ends when the failure is cleared."
::= { jnxpwTDMPerf1DayIntervalEntry 12 }
-- End of PW TDM Performance table
-- Conformance Information
jnxpwTDMGroups OBJECT IDENTIFIER ::= { jnxpwTDMConformance 1 }
jnxpwTDMCompliances OBJECT IDENTIFIER ::= { jnxpwTDMConformance 2 }
jnxpwTDMModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agent that support TDM PW
over PSN operation."
MODULE -- this module
MANDATORY-GROUPS { jnxpwTDMGroup,
jnxpwTDMPerfCurrentGroup,
jnxpwTDMPerfIntervalGroup,
jnxpwTDMPerf1DayIntervalGroup
}
OBJECT jnxpwGenTDMCfgIndex
MIN-ACCESS read-only
DESCRIPTION
"The ability to set the an index pointer
is not required."
OBJECT jnxpwRelTDMCfgIndex
MIN-ACCESS read-only
DESCRIPTION
"The ability to set the an index pointer
is not required."
OBJECT jnxpwTDMCfgPktReorder
MIN-ACCESS read-only
DESCRIPTION
"The ability to set the packet reordering
is not required."
OBJECT jnxpwTDMCfgRtpHdrUsed
MIN-ACCESS read-only
DESCRIPTION
"The ability to set whether to use the
RTP header or not is not required."
OBJECT jnxpwTDMCfgPayloadSuppression
MIN-ACCESS read-only
DESCRIPTION
"The ability to set this object is not
required."
OBJECT jnxpwTDMCfgPktReplacePolicy
MIN-ACCESS read-only
DESCRIPTION
"The ability to set the replace policy
is not required."
OBJECT jnxpwTDMCfgStorageType
MIN-ACCESS read-only
DESCRIPTION
"The ability to set the storage type is
not required."
OBJECT jnxpwTDMCfgPktFiller
MIN-ACCESS read-only
DESCRIPTION
"The ability to set the Filler pattern
is not required."
OBJECT jnxpwTDMCfgName
MIN-ACCESS read-only
DESCRIPTION
"The ability to set the an Aliase
is not required."
::= { jnxpwTDMCompliances 1 }
-- Units of conformance.
jnxpwTDMGroup OBJECT-GROUP
OBJECTS {
jnxpwTDMRate,
jnxpwTDMIfIndex,
jnxpwGenTDMCfgIndex,
jnxpwRelTDMCfgIndex,
jnxpwTDMConfigError,
jnxpwTDMTimeElapsed,
jnxpwTDMValidIntervals,
jnxpwTDMValidDayIntervals,
jnxpwTDMLastEsTimeStamp,
jnxpwTDMCfgIndexNext,
jnxpwTDMCfgRowStatus,
jnxpwTDMCfgPayloadSize,
jnxpwTDMCfgPktReorder,
jnxpwTDMCfgRtpHdrUsed,
jnxpwTDMCfgJtrBfrDepth,
jnxpwTDMCfgPayloadSuppression,
jnxpwTDMCfgConsecPktsInSynch,
jnxpwTDMCfgConsecMissPktsOutSynch,
jnxpwTDMCfgSetUp2SynchTimeOut,
jnxpwTDMCfgPktReplacePolicy,
jnxpwTDMCfgAvePktLossTimeWindow ,
jnxpwTDMCfgExcessivePktLossThreshold,
jnxpwTDMCfgAlarmThreshold ,
jnxpwTDMCfgClearAlarmThreshold,
jnxpwTDMCfgMissingPktsToSes,
jnxpwTDMCfgTimestampMode,
jnxpwTDMCfgStorageType,
jnxpwTDMCfgPktFiller,
jnxpwTDMCfgName
}
STATUS current
DESCRIPTION
"Collection of objects for basic TDM PW config and
status."
::= { jnxpwTDMGroups 1 }
jnxpwTDMPerfCurrentGroup OBJECT-GROUP
OBJECTS {
jnxpwTDMPerfCurrentMissingPkts,
jnxpwTDMPerfCurrentPktsReOrder,
jnxpwTDMPerfCurrentJtrBfrUnderruns,
jnxpwTDMPerfCurrentMisOrderDropped,
jnxpwTDMPerfCurrentMalformedPkt,
jnxpwTDMPerfCurrentESs,
jnxpwTDMPerfCurrentSESs,
jnxpwTDMPerfCurrentUASs,
jnxpwTDMPerfCurrentFC
}
STATUS current
DESCRIPTION
"Collection of current statistics objects for TDM PWs."
::= { jnxpwTDMGroups 2 }
jnxpwTDMPerfIntervalGroup OBJECT-GROUP
OBJECTS {
jnxpwTDMPerfIntervalValidData,
jnxpwTDMPerfIntervalDuration,
jnxpwTDMPerfIntervalMissingPkts,
jnxpwTDMPerfIntervalPktsReOrder,
jnxpwTDMPerfIntervalJtrBfrUnderruns,
jnxpwTDMPerfIntervalMisOrderDropped,
jnxpwTDMPerfIntervalMalformedPkt,
jnxpwTDMPerfIntervalESs,
jnxpwTDMPerfIntervalSESs,
jnxpwTDMPerfIntervalUASs,
jnxpwTDMPerfIntervalFC
}
STATUS current
DESCRIPTION
"Collection of Interval statistics objects for TDM PWs."
::= { jnxpwTDMGroups 3 }
jnxpwTDMPerf1DayIntervalGroup OBJECT-GROUP
OBJECTS {
jnxpwTDMPerf1DayIntervalValidData,
jnxpwTDMPerf1DayIntervalDuration,
jnxpwTDMPerf1DayIntervalMissingPkts,
jnxpwTDMPerf1DayIntervalPktsReOrder,
jnxpwTDMPerf1DayIntervalJtrBfrUnderruns,
jnxpwTDMPerf1DayIntervalMisOrderDropped,
jnxpwTDMPerf1DayIntervalMalformedPkt,
jnxpwTDMPerf1DayIntervalESs,
jnxpwTDMPerf1DayIntervalSESs,
jnxpwTDMPerf1DayIntervalUASs,
jnxpwTDMPerf1DayIntervalFC
}
STATUS current
DESCRIPTION
"Collection of Daily statistics objects for TDM PWs."
::= { jnxpwTDMGroups 4 }
END