mibs/junos/JUNIPER-SOAM-PM-MIB
--
-- Juniper Enterprise Specific MIB: SOAM
--
-- Copyright (c) 2012-2013, Juniper Networks, Inc.
-- All rights reserved.
--
-- The contents of this document are subject to change without notice.
--
JUNIPER-SOAM-PM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
Integer32, Counter32, Counter64,
Unsigned32,Gauge32 FROM SNMPv2-SMI -- [RFC2578]
TEXTUAL-CONVENTION,
TimeInterval,
TimeStamp, RowStatus,
TruthValue, MacAddress,
TDomain, TAddress, DateAndTime FROM SNMPv2-TC -- [RFC2579]
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580]
InterfaceIndex,
InterfaceIndexOrZero FROM IF-MIB -- [RFC2863]
LldpChassisId,
LldpChassisIdSubtype,
LldpPortId,
LldpPortIdSubtype FROM LLDP-MIB -- [IEEExxx]
ieee802dot1mibs,
IEEE8021VlanIndex FROM IEEE8021-TC-MIB
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
dot1agCfmMepEntry,
Dot1afCfmIndexIntegerNextFree,
Dot1agCfmMepIdOrZero FROM IEEE8021-CFM-MIB
jnxMibs FROM JUNIPER-SMI
IEEE8021PriorityValue FROM IEEE8021-TC-MIB
;
jnxSoamPmMib MODULE-IDENTITY
LAST-UPDATED "201605310000Z" -- Tue May 31 00:00:00 2016 UTC
ORGANIZATION "Juniper Networks, Inc."
CONTACT-INFO
"Juniper Technical Assistance Center
Juniper Networks, Inc.
1133 Innovation Way
Sunnyvale, CA 94089
E-mail: support@juniper.net"
DESCRIPTION
"This MIB module contains the management objects for the
management of Ethernet Services Operations, Administration
and Maintenance for Performance Monitoring.
"
REVISION "201201131200Z" -- January 13, 2012
DESCRIPTION
"Initial Version."
REVISION "201605310000Z" -- 31-May-16
DESCRIPTION
"Removed duplicate entries"
::= { jnxMibs 78 }
-- *****************************************************************************
-- Object definitions in the SOAM PM MIB Module
-- *****************************************************************************
jnxSoamPmNotifications OBJECT IDENTIFIER ::= { jnxSoamPmMib 0 }
jnxSoamPmMibObjects OBJECT IDENTIFIER ::= { jnxSoamPmMib 1 }
jnxSoamPmMibConformance OBJECT IDENTIFIER ::= { jnxSoamPmMib 2 }
-- *****************************************************************************
-- Groups in the SOAM PM MIB Module
-- *****************************************************************************
jnxSoamPmMep OBJECT IDENTIFIER ::= { jnxSoamPmMibObjects 1 }
jnxSoamPmLmObjects OBJECT IDENTIFIER ::= { jnxSoamPmMibObjects 2 }
jnxSoamPmDmObjects OBJECT IDENTIFIER ::= { jnxSoamPmMibObjects 3 }
jnxSoamPmNotificationCfg OBJECT IDENTIFIER ::= { jnxSoamPmMibObjects 4 }
jnxSoamPmNotificationObj OBJECT IDENTIFIER ::= { jnxSoamPmMibObjects 5 }
-- ******************************************************************
-- Textual conventions
-- ******************************************************************
JnxSoamTcTestPatternType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This enumeration data type indicates the type of test pattern to be
sent in an OAM PDU Test TLV.
The valid enumerated values associated with this type are:
null(1) Null signal without CRC-32
nullCrc32(2) Null signal with CRC-32
prbs(3) PRBS 2^31-1 without CRC-32
prbsCrc32(4) PRBS 2^31-1 with CRC-32
"
REFERENCE
"[MEF7.1], Appendix III.2 Enumeration, [Y.1731] 7.7"
SYNTAX INTEGER {
null(1),
nullCrc32(2),
prbs(3),
prbsCrc32(4)
}
JnxSoamTcDataPatternType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This enumeration data type indicates the type of data pattern to be
sent in an OAM PDU Data TLV.
The valid enumerated values associated with this type are:
zeroPattern(1) indicates the Data TLV contains all zeros
onesPattern(2) indicates the Data TLV contains all ones
"
SYNTAX INTEGER {
zeroPattern(1),
onesPattern(2)
}
JnxSoamTcOperationTimeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This enumeration data type indicates the operation type start
or end time to indicate when an OAM operation is
initiated or stopped.
The valid enumerated values associated with this type are:
none(1) The operation is never started or is stopped immediately
if used to indicate a start time, or the operation never
ends if it is used to indicate an end time
immediate(2) The operation is to begin immediately
relative(3) The operation is to begin at a relative time from the
current time or stop a relative time after it has started
fixed(4) The operation is to begin/stop at the given UTC time/date
"
REFERENCE
"[SOAM-PM] R2, [SOAM-FM] 8.7"
SYNTAX INTEGER {
none(1),
immediate(2),
relative(3),
fixed(4)
}
JnxSoamTcAvailabilityType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This enumeration data type defines the availability of a session,
measured by a loss measurement session. The valid enumerated values
associated with this type are:
available(1) indicates the MEP is available.
unavailable(2) indicates the MEP is unavailable.
unknown(3) indicates the availability is not known, for
instance because insufficient time has passed to
make an availability calculation, the time has been
excluded because of a maintenance interval, or because
availability measurement is not enabled.
"
SYNTAX INTEGER {
available(1),
unavailable(2),
unknown(3)
}
JnxSoamTcDelayMeasurementBinType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This enumeration data type is used to distinguish between
measurement bins for Frame Delay, Frame Delay Range, and
Inter-frame Delay variation.
The valid enumerated values associated with this type are:
twoWayFrameDelay(1) indicates a measurement bin for two-way
Frame Delay.
forwardFrameDelay(2) indicates a measurement bin for one-way
Frame Delay in the forward direction.
backwardFrameDelay(3) indicates a measurement bin for one-way
Frame Delay in the backward direction.
twoWayIfdv(4) indicates a measurement bin for two-way
Inter-frame Delay Variation.
forwardIfdv(5) indicates a measurement bin for one-way
Inter-frame Delay Variation in the forward
direction.
backwardIfdv(6) indicates a measurement bin for one-way
Inter-frame Delay Variation in the backward
direction.
twoWayFrameDelayRange(7) indicates a measurement bin for two-way
Frame Delay Range.
forwardFrameDelayRange(8) indicates a measurement bin for one-way
Frame Delay Range in the forward direction.
backwardFrameDelayRange(9) indicates a measurement bin for one-way
Frame Delay Range in the backward direction.
"
SYNTAX INTEGER {
twoWayFrameDelay(1),
forwardFrameDelay(2),
backwardFrameDelay(3),
twoWayIfdv(4),
forwardIfdv(5),
backwardIfdv(6),
twoWayFrameDelayRange(7),
forwardFrameDelayRange(8),
backwardFrameDelayRange(9)
}
-- *****************************************************************************
-- Ethernet MEP Performance Monitoring Configuration
-- *****************************************************************************
jnxSoamPmMepTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamPmMepEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is an extension of the dot1agCfmMepTable and rows
are automatically added or deleted from this table based upon row
creation and destruction of the dot1agCfmMepTable.
This table represents the local MEP PM configuration table. The
primary purpose of this table is provide local parameters for the
SOAM PM function found in [Y.1731] and [MEF SOAM-PM] and instantiated
at a MEP.
"
REFERENCE
"[Y.1731], [MEF SOAM-PM]"
::= { jnxSoamPmMep 1 }
jnxSoamPmMepEntry OBJECT-TYPE
SYNTAX JnxSoamPmMepEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamPmMepTable."
AUGMENTS {
dot1agCfmMepEntry
}
--INDEX { dot1agCfmMdIndex,
-- dot1agCfmMaIndex,
-- dot1agCfmMepIdentifier
-- }
::= { jnxSoamPmMepTable 1 }
JnxSoamPmMepEntry ::= SEQUENCE {
jnxSoamPmMepOperNextIndex Dot1afCfmIndexIntegerNextFree,
jnxSoamPmMepLmSingleEndedResponder TruthValue,
jnxSoamPmMepSlmSingleEndedResponder TruthValue,
jnxSoamPmMepDmSingleEndedResponder TruthValue
}
jnxSoamPmMepOperNextIndex OBJECT-TYPE
SYNTAX Dot1afCfmIndexIntegerNextFree
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an unused value for a PM session number on a
MEP that can be used for either LM or DM sessions, or a zero to
indicate that none exist. This value needs to be read in order to
find an available index for row-creation of a PM session on a MEP and
then used when a row is created. This value is automatically updated
by the SNMP Agent after the row is created.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never to be reused for other PM sessions on the same MEP while this
session is active, or until it wraps to zero. The index value keeps
increasing up to that time. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused.
This object is an extension of the dot1agCfmMepTable and the object is
automatically added or deleted based upon row creation and destruction
of the dot1agCfmMepTable.
"
::= { jnxSoamPmMepEntry 1 }
jnxSoamPmMepLmSingleEndedResponder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies whether the Loss Measurement (LMM) single-ended
Responder is enabled.
The value 'true' indicates the single-ended Loss Measurement Responder
is enabled and if a LMM message is received a LMR will be sent in reply.
The value 'false' indicates the single-ended Loss Measurement Responder
is disabled. If a LMM message is received no response will be sent and
the message will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.
"
DEFVAL { true }
::= { jnxSoamPmMepEntry 2 }
jnxSoamPmMepSlmSingleEndedResponder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies whether the Synthetic Loss Measurement (SLM)
single-ended Responder is enabled.
The value 'true' indicates the single-ended SLM Responder is enabled and
if a SLM message is received a SLR will be sent in reply.
The value 'false' indicates the single-ended SLM Responder is disabled.
If a SLM message is received no response will be sent and the message
will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.
"
DEFVAL { true }
::= { jnxSoamPmMepEntry 3 }
jnxSoamPmMepDmSingleEndedResponder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies whether the Delay Measurement (DMM) single
ended Responder is enabled.
The value 'true' indicates the single-ended Delay Measurement Responder
is enabled and if a DMM message is received a DMR will be sent in reply.
The value 'false' indicates the single-ended Delay Measurement Responder
is disabled. If a DMM message is received no response will be sent and
the message will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.
"
DEFVAL { true }
::= { jnxSoamPmMepEntry 4 }
-- *****************************************************************************
-- Ethernet Loss Measurement Configuration Table
-- *****************************************************************************
jnxSoamLmCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamLmCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table includes configuration objects and operations for the
Frame Loss Measurement function defined in [Y.1731] and [MEF SOAM-PM].
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP. A
Loss Measurement session is created on an existing MEP by first
accessing the jnxSoamPmMepOperNextIndex object and using this value as
the jnxSoamLmCfgIndex in the row creation.
Some writable objects in this table are only applicable in certain cases
(as described under each object), and attempts to write values for them
in other cases will be ignored.
The writable objects in this table need to be persistent upon reboot
or restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R68; [Y.1731]"
::= { jnxSoamPmLmObjects 1 }
jnxSoamLmCfgEntry OBJECT-TYPE
SYNTAX JnxSoamLmCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamLmCfgTable."
INDEX { dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamLmCfgIndex
}
::= { jnxSoamLmCfgTable 1 }
JnxSoamLmCfgEntry ::= SEQUENCE {
jnxSoamLmCfgIndex Unsigned32,
jnxSoamLmCfgType INTEGER,
jnxSoamLmCfgVersion Unsigned32,
jnxSoamLmCfgEnabled TruthValue,
jnxSoamLmCfgMeasurementEnable BITS,
jnxSoamLmCfgMessagePeriod Integer32,
jnxSoamLmCfgPriority IEEE8021PriorityValue,
jnxSoamLmCfgFrameSize Unsigned32,
jnxSoamLmCfgDataPattern JnxSoamTcDataPatternType,
jnxSoamLmCfgTestTlvIncluded TruthValue,
jnxSoamLmCfgTestTlvPattern JnxSoamTcTestPatternType,
jnxSoamLmCfgNumIntervalsStored Unsigned32,
jnxSoamLmCfgDestMepId Dot1agCfmMepIdOrZero,
jnxSoamLmCfgDestIsMepId TruthValue,
jnxSoamLmCfgStartTimeType JnxSoamTcOperationTimeType,
jnxSoamLmCfgFixedStartDateAndTime DateAndTime,
jnxSoamLmCfgRelativeStartTime TimeInterval,
jnxSoamLmCfgRepetitionTime Unsigned32,
jnxSoamLmCfgAlignMeasurementIntervals TruthValue,
jnxSoamLmCfgAlignMeasurementOffset Unsigned32,
jnxSoamLmCfgSessionType OCTET STRING,
jnxSoamLmCfgSessionStatus OCTET STRING,
jnxSoamLmCfgHistoryClear TruthValue,
jnxSoamLmCfgRowStatus RowStatus,
jnxSoamLmCfgMeasurementInterval Unsigned32,
jnxSoamLmCfgDestMacAddress MacAddress,
jnxSoamLmCfgStopTimeType JnxSoamTcOperationTimeType,
jnxSoamLmCfgFixedStopDateAndTime DateAndTime,
jnxSoamLmCfgRelativeStopTime TimeInterval,
jnxSoamLmCfgAvailabilityMeasurementInterval Unsigned32,
jnxSoamLmCfgAvailabilityNumConsecutiveMeasPdus Unsigned32,
jnxSoamLmCfgAvailabilityFlrThreshold Unsigned32,
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals Unsigned32,
jnxSoamLmCfgAvailabilityNumConsecutiveHighFlr Unsigned32
}
jnxSoamLmCfgIndex
OBJECT-TYPE
SYNTAX Unsigned32(1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An index to the Loss Measurement Configuration table which indicates
the specific measurement session for the MEP.
jnxSoamPmMepOperNextIndex needs to be inspected to find an
available index for row-creation.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused for other PM sessions on the same MEP while this
session is active. The index value keeps increasing until it
wraps to 0. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused.
"
::= { jnxSoamLmCfgEntry 1 }
jnxSoamLmCfgType OBJECT-TYPE
SYNTAX INTEGER {
lmLmm (1),
lmSlm (2),
lmCcm (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies what type of Loss Measurement
will be performed.
lmLmm(1) LMM SOAM PDU generated and received LMR responses tracked
lmSlm(2) SLM SOAM PDU generated and received SLR responses tracked
lmCcm(3) CCM SOAM PDU generated and received CCM PDUs tracked
The lmSlm value is required. The lmLmm and lmCcm values are optional.
The lmCcm loss measurement values are only valid for a point-to-point
MEG. Multipoint MEGs may give unreliable loss measurements.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[Y.1731] [MEF SOAM-PM] R51, R68, O7, R102"
DEFVAL { lmSlm }
::= { jnxSoamLmCfgEntry 2 }
jnxSoamLmCfgVersion OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the version of the PDUs used to perform
Loss Measurement.
The value is placed in the Version field of the PDU and indicates
that the PDU format used is the format defined in Y.1731 with
that version.
The exact PDUs to use are specified by this object in combination with
jnxSoamLmCfgType.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[Y.1731]"
DEFVAL { 0 }
::= { jnxSoamLmCfgEntry 3 }
jnxSoamLmCfgEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies whether the Loss Measurement session
is enabled.
The value 'true' indicates the Loss Measurement session is enabled and
SOAM PDUs are sent and/or measurements are collected when the session
is running according to the scheduling objects (start time, stop time,
etc.).
The value 'false' indicates the Loss Measurement session is disabled
and SOAM PDUs are not sent and/or measurements collected.
For a Loss Measurement session to be removed the row is
deleted in order to release internal resources.
This object can written/modified after row creation time.
If the LM session is enabled it resumes after shutdown/restart.
If the LM session is disabled the current Measurement Interval is
stopped, if it in process at the time, and all the in process calculations
for the partially completed Measurement Interval are finalized.
This object does not affect whether the single-ended Responder is
enabled or not, which is enabled or disabled by the
jnxSoamPmMepLmSingleEndedResponder and
jnxSoamPmMepSlmSingleEndedResponder objects.
"
REFERENCE
"[MEF SOAM-PM] R4, R5, R6, O1, R12, R14"
DEFVAL { true }
::= { jnxSoamLmCfgEntry 4 }
jnxSoamLmCfgMeasurementEnable OBJECT-TYPE
SYNTAX BITS {
bForwardTransmitedFrames(0),
bForwardReceivedFrames(1),
bForwardMinFlr(2),
bForwardMaxFlr(3),
bForwardAvgFlr(4),
bBackwardTransmitedFrames(5),
bBackwardReceivedFrames(6),
bBackwardMinFlr(7),
bBackwardMaxFlr(8),
bBackwardAvgFlr(9),
bSoamPdusSent(10),
bSoamPdusReceived (11),
bAvailForwardHighLoss(12),
bAvailForwardConsecutiveHighLoss(13),
bAvailForwardAvailable(14),
bAvailForwardUnavailable(15),
bAvailForwardMinFlr(16),
bAvailForwardMaxFlr(17),
bAvailForwardAvgFlr(18),
bAvailBackwardHighLoss(19),
bAvailBackwardConsecutiveHighLoss(20),
bAvailBackwardAvailable(21),
bAvailBackwardUnavailable(22),
bAvailBackwardMinFlr(23),
bAvailBackwardMaxFlr(24),
bAvailBackwardAvgFlr(25),
bMeasuredStatsForwardMeasuredFlr(26),
bMeasuredStatsBackwardMeasuredFlr(27),
bMeasuredStatsAvailForwardStatus(28),
bMeasuredStatsAvailBackwardStatus(29)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A vector of bits that indicates the type of SOAM LM counters found
in the jnxSoamLmMeasuredStatsTable, jnxSoamLmCurrentStatsTable,
jnxSoamLmHistoryStatsTable that are enabled.
that are enabled.
A bit set to '1' enables the specific SOAM LM counter. A bit set to
'0' disables the SOAM LM counter.
If a particular SOAM LM counter is not supported the BIT value is
set to '0'.
Not all SOAM LM counters are supported for all SOAM LM types.
This object can only be written at row creation time and cannot be
modified once it has been created.
bForwardTransmitedFrames (0)
Enables/disables the jnxSoamLmCurrentStatsForwardTransmittedFrames
and jnxSoamLmHistoryStatsForwardTransmittedFrames counters.
bForwardReceivedFrames(1)
Enables/disables the jnxSoamLmCurrentStatsForwardReceivedFrames
and jnxSoamLmHistoryStatsForwardReceivedFrames counters.
bForwardMinFlr(2)
Enables/disables the jnxSoamLmCurrentStatsForwardMinFlr
and jnxSoamLmHistoryStatsForwardMinFlr counters.
bForwardMaxFlr(3)
Enables/disables the jnxSoamLmCurrentStatsForwardMaxFlr
and jnxSoamLmHistoryStatsForwardMaxFlr counters.
bForwardAvgFlr(4)
Enables/disables the jnxSoamLmCurrentStatsForwardAvgFlr
and jnxSoamLmHistoryStatsForwardAvgFlr counters.
bBackwardTransmitedFrames(5)
Enables/disables the jnxSoamLmCurrentStatsBackwardTransmittedFrames
and jnxSoamLmHistoryStatsBackwardTransmittedFrames counters.
bBackwardReceivedFrames(6)
Enables/disables the jnxSoamLmCurrentStatsBackwardReceivedFrames
and jnxSoamLmHistoryStatsBackwardReceivedFrames counters.
bBackwardMinFlr(7)
Enables/disables the jnxSoamLmCurrentStatsBackwardMinFlr
and jnxSoamLmHistoryStatsBackwardMinFlr counters.
bBackwardMaxFlr(8)
Enables/disables the jnxSoamLmCurrentStatsBackwardMaxFlr
and jnxSoamLmHistoryStatsBackwardMaxFlr counters.
bBackwardAvgFlr(9)
Enables/disables the jnxSoamLmCurrentStatsBackwardAvgFlr
and jnxSoamLmHistoryStatsBackwardAvgFlr counters.
bSoamPdusSent (10)
Enables/disables the jnxSoamLmCurrentStatsSoamPdusSent
and jnxSoamLmHistoryStatsSoamPdusSent counters.
bSoamPdusReceivedbReceivedMeasurements (11)
Enables/disables the jnxSoamLmCurrentStatsSoamPdusReceived
and jnxSoamLmHistoryStatsSoamPdusReceived counters.
bAvailForwardHighLoss(12)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardHighLoss
and jnxSoamLmHistoryAvailStatsForwardHighLoss counters.
bAvailForwardConsecutiveHighLoss(13)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardConsecutiveHighLoss
and jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLoss counters.
bAvailForwardAvailable(14)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardAvailable
and jnxSoamLmHistoryAvailStatsForwardAvailable counters.
bAvailForwardUnavailable(15)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardUnavailable
and jnxSoamLmHistoryAvailStatsForwardUnavailable counters.
bAvailForwardMinFlr(16)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardMinFlr
and jnxSoamLmHistoryAvailStatsForwardMinFlr counters.
bAvailForwardMaxFlr(17)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardMaxFlr
and jnxSoamLmHistoryAvailStatsForwardMaxFlr counters.
bAvailForwardAvgFlr(18)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardAvgFlr
and jnxSoamLmHistoryAvailStatsForwardAvgFlr counters.
bAvailBackwardHighLoss(19)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardHighLoss
and jnxSoamLmHistoryAvailStatsBackwardHighLoss counters.
bAvailBackwardConsecutiveHighLoss(20)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss
and jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss counters.
bAvailBackwardAvailable(21)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardAvailable
and jnxSoamLmHistoryAvailStatsBackwardAvailable counters.
bAvailBackwardUnavailable(22)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardUnavailable
and jnxSoamLmHistoryAvailStatsBackwardUnavailable counters.
bAvailBackwardMinFlr(23)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardMinFlr
and jnxSoamLmHistoryAvailStatsBackwardMinFlr counters.
bAvailBackwardMaxFlr(24)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardMaxFlr
and jnxSoamLmHistoryAvailStatsBackwardMaxFlr counters.
bAvailBackwardAvgFlr(25)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardAvgFlr
and jnxSoamLmHistoryAvailStatsBackwardAvgFlr counters.
Enables/disables the jnxSoamLmCurrentStatsSoamPdusReceived
and jnxSoamLmHistoryStatsSoamPdusReceived counters.
bMeasuredStatsForwardMeasuredFlr(26)
Enables/disables the jnxSoamLmMeasuredStatsForwardFlr counter.
bMeasuredStatsBackwardMeasuredFlr(27)
Enables/disables the jnxSoamLmMeasuredStatsBackwardFlr counter.
bMeasuredStatsAvailForwardStatus(28)
Enables/disables the jnxSoamLmMeasuredStatsAvailForwardStatus counter.
bMeasuredStatsAvailBackwardStatus(29)
Enables/disables the jnxSoamLmMeasuredStatsAvailBackwardStatus counter.
"
REFERENCE
"[Y.1731]"
DEFVAL { { } }
::= { jnxSoamLmCfgEntry 5 }
jnxSoamLmCfgMessagePeriod OBJECT-TYPE
SYNTAX Integer32
UNITS "ms"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval between Loss Measurement
OAM message transmission. For Loss Measurement monitoring
applications the default value is 1 sec.
This object is not applicable if jnxSoamLmCfgType is set to lmCcm
and is ignored for that Loss Measurement Type.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R76, R77, D29, D30"
DEFVAL { 1000 }
::= { jnxSoamLmCfgEntry 6 }
jnxSoamLmCfgPriority OBJECT-TYPE
SYNTAX IEEE8021PriorityValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Loss Measurement OAM message priority
as well as the priority of the service/OAM traffic to be monitored.
Only frames of the same Class of Service are counted.
The default value is to be the value which yields the lowest frame
loss.
This object is not applicable if jnxSoamLmCfgType is set to lmCcm.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R1, R2, R71, D28, R72, R73, R105-R109, D45;
[MEF 10.2.1] Section 6.8"
::= { jnxSoamLmCfgEntry 7 }
jnxSoamLmCfgFrameSize OBJECT-TYPE
SYNTAX Unsigned32 (64..9600)
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Loss Measurement frame size between
64 bytes and the maximum transmission unit of the EVC.
The range of frame sizes from 64 through 2000 octets need to be
supported, and the range of frame sizes from 2001 through 9600 octets
is suggested be supported.
The adjustment to the frame size of the standard frame size is
accomplished by the addition of a Data or Test TLV. A Data or Test TLV
is only added to the frame if the frame size is greater than 64 bytes.
This object is only valid for the entity transmitting the Loss
Measurement frames, type 'lmSlm', and is ignored by the
entity receiving frames. It is not applicable for the 'lmCcm' or
'lmLmm' types.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R78, R79, D31, D32 [Y.1731]"
DEFVAL { 64 }
::= { jnxSoamLmCfgEntry 8 }
jnxSoamLmCfgDataPattern OBJECT-TYPE
SYNTAX JnxSoamTcDataPatternType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the LM data pattern included in a Data TLV
when the size of the LM frame is determined by the
jnxSoamLmFrameSize object and jnxoamLmTestTlvIncluded is 'false'.
If the frame size object does not define the LM frame size or
jnxSoamLmTestTlvIncluded is 'true' the value of this object is
ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
DEFVAL { zeroPattern }
::= { jnxSoamLmCfgEntry 9 }
jnxSoamLmCfgTestTlvIncluded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether a Test TLV or Data TLV is included when the size
of the LM frame is determined by the jnxSoamLmFrameSize object.
A value of 'true' indicates that the Test TLV is to be included. A
value of 'false' indicates that the Data TLV is to be included.
If the frame size object does not define the LM frame size
the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[Y.1731] 9.3"
DEFVAL { false }
::= { jnxSoamLmCfgEntry 10 }
jnxSoamLmCfgTestTlvPattern OBJECT-TYPE
SYNTAX JnxSoamTcTestPatternType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the type of test pattern to be
sent in the LM frame Test TLV when the size of LM PDU is
determined by the jnxSoamLmFrameSize object and
jnxSoamLmTestTlvIncluded is 'true'. If the frame size object
does not define the LM frame size or jnxSoamLmTestTlvIncluded
is 'false' the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
DEFVAL { null }
::= { jnxSoamLmCfgEntry 11 }
jnxSoamLmCfgNumIntervalsStored OBJECT-TYPE
SYNTAX Unsigned32 (1..1000)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the number of completed Measurement Intervals
to store in the history statistic table (jnxSoamLmHistoryStatsTable)
At least 32 completed Measurement Intervals need to be stored. 96
Measurement Intervals are recommended to be stored.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R21, D8, D9"
DEFVAL { 32 }
::= { jnxSoamLmCfgEntry 12 }
jnxSoamLmCfgDestMepId OBJECT-TYPE
SYNTAX Dot1agCfmMepIdOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Maintenance Association End Point Identifier of
another MEP in the same Maintenance Association to which
the SOAM LM frame is to be sent.
This address will be used if the value of the column
jnxSoamLmDestIsMepId is 'true'. A value of zero
means that the destination MEP ID has not been configured.
This object is only valid for the entity transmitting the Loss
Measurement frames, types 'lmLmm' and 'lmSlm'. It is not applicable for
the 'lmCcm' type.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R70, R104"
DEFVAL { 0 }
::= { jnxSoamLmCfgEntry 13 }
jnxSoamLmCfgDestIsMepId OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A value of 'true' indicates that MEPID of the target MEP is used for
SOAM LM frame transmission.
A value of 'false' indicates that the MAC address of the
target MEP is used for SOAM LM frame transmission.
This object is only valid for the entity transmitting the Loss
Measurement frames, types 'lmLmm' and 'lmSlm'. It is not applicable for
the 'lmCcm' type.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R70, R104"
DEFVAL { true }
::= { jnxSoamLmCfgEntry 14 }
jnxSoamLmCfgStartTimeType OBJECT-TYPE
SYNTAX JnxSoamTcOperationTimeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the type of start time of the SOAM LM
session. The start time can be disabled (none), immediate, relative,
or fixed.
The value of 'none' is illegal and a write error will be returned
if this value is used.
The value of 'immediate' starts the SOAM LM session when the
jnxSoamLmCfgEnabled is true.
The value of 'fixed' starts the SOAM LM session when the
jnxSoamLmFixedStartDateAndTime is less than or equal to the current
system date and time and jnxSoamLmCfgEnabled is true. This value is used
to implement an On-Demand fixed time PM session.
The value of 'relative' starts the SOAM LM session when the current
system date and time minus the jnxSoamLmRelativeStartTime is greater
than or equal to the system date and time when the jnxSoamLmStartTimeType
object was written and jnxSoamLmCfgEnabled is true. This value is used
to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R3, R7, R8, D1"
DEFVAL { immediate }
::= { jnxSoamLmCfgEntry 15 }
jnxSoamLmCfgFixedStartDateAndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the fixed start date/time for the
SOAM Loss Measurement session. This object is used only used if
jnxSoamLmStartTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R9"
DEFVAL { '0000010100000000'H }
::= { jnxSoamLmCfgEntry 16 }
jnxSoamLmCfgRelativeStartTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the relative start time, from the
current system time, for the SOAM LM session. This
object is used only if jnxSoamLmStartTimeType is 'relative' and is
ignored otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R9"
DEFVAL { 0 }
::= { jnxSoamLmCfgEntry 17 }
jnxSoamLmCfgRepetitionTime OBJECT-TYPE
SYNTAX Unsigned32 (0..31536000)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies a configurable repetition time between
Measurement Intervals in a Loss Measurement session, in seconds.
If the value is 0 (none), there is no time gap between the end of one
Measurement Interval and the start of a new Measurement Interval.
This is the normal usage case.
If the value is greater than 0 but less than or equal to the measurement
interval, an error is returned.
If the value is greater than one Measurement Interval there is time gap
between the end of one Measurement Interval and the start of the next
Measurement Interval. The repetition time specifies the time between
the start of consecutive Measurement Intervals; hence the gap between
the end of one Measurement Interval and the start of the next is equal
to the difference between the repetition time and the measurement
interval. During this gap, no SOAM PDUs are sent for this session and
no measurements are made.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R18, D3, R19, R20"
DEFVAL { 0 }
::= { jnxSoamLmCfgEntry 18 }
jnxSoamLmCfgAlignMeasurementIntervals OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies whether the Measurement Intervals for
the Loss Measurement session are aligned with a zero offset to
real time.
The value 'true' indicates that each Measurement Interval starts
at a time which is aligned to NE time source hour, if the repetition
time (or the Measurement Interval, if the repetition time is 0) is
a factor of an hour, i.e. 60min/15min = 4. For instance, a
Measurement Interval/repetition time of 15 minutes would stop/start
the Measurement Interval at 0, 15, 30, and 45 minutes of an hour. A
Measurement Interval/Repetition Time of 7 minutes would not align
to the hour since 7 minutes is NOT a factor of an hour, i.e.
60min/7min = 8.6. In this case the behavior is the same as if the
object is set to 'false'.
The value 'false' indicates that the first Measurement Interval starts
at an arbitrary time and each subsequent Measurement Interval starts
at a time which is determined by jnxSoamLmCfgRepetitionTime.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] D4, D5, D6"
DEFVAL { true }
::= { jnxSoamLmCfgEntry 19 }
jnxSoamLmCfgAlignMeasurementOffset OBJECT-TYPE
SYNTAX Unsigned32 (0..525600)
UNITS "minutes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the offset in minutes from the time of day value
if jnxSoamLmCfgAlignMeasurementIntervals is 'true' and the repetition
time is a factor of 60 minutes. If not, the value of this object
is ignored.
If the Measurement Interval is 15 minutes and
jnxSoamLmCfgAlignMeasurementIntervals is true and if this object was
set to 5 minutes, the Measurement Intervals would start at 5, 20, 35, 50
minutes past each hour.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] D7"
DEFVAL { 0 }
::= { jnxSoamLmCfgEntry 20 }
jnxSoamLmCfgSessionType OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1..42))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the current session is defined to
be 'Proactive' or 'On-Demand'. A value of 'proactive'
indicates the current session is 'Proactive'. A value of 'onDemand'
indicates the current session is 'On-Demand'.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R3"
DEFVAL { "proactive" }
::= { jnxSoamLmCfgEntry 21 }
jnxSoamLmCfgSessionStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1..44))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current status of the LM session. A value
of 'active' indicates the current LM session is active, i.e. the current
time lies between the start time and the stop time, and
jnxSoamLmCfgEnabled is true. A value of 'notActive' indicates the
current LM session is not active, i.e. it has not started yet, has
stopped upon reaching the stop time, or is disabled.
"
::= { jnxSoamLmCfgEntry 22 }
jnxSoamLmCfgHistoryClear OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object when written clears the Loss Measurement history
Table (jnxSoamLmHistoryStatsTable) - all rows are deleted.
When read the value always returns 'false'.
Writing this value does not change the current stat table,
nor any of the items in the configuration table.
Writing this value during row creation has no effect.
"
DEFVAL { false }
::= { jnxSoamLmCfgEntry 23 }
jnxSoamLmCfgRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the row.
The writable columns in a row cannot be changed if the row
is active, except for jnxSoamLmCfgHistoryClear and jnxSoamLmCfgEnabled
objects. All columns must have a valid value before a row
can be activated.
"
::= { jnxSoamLmCfgEntry 24 }
jnxSoamLmCfgMeasurementInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..525600)
UNITS "minutes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Measurement Interval for FLR statistics,
in minutes. A Measurement Interval of 15 minutes needs to be supported,
other intervals may be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R16, R17, R110, R111, D46"
DEFVAL { 15 }
::= { jnxSoamLmCfgEntry 25 }
jnxSoamLmCfgDestMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Target or Destination MAC Address Field to be transmitted.
If jnxSoamLmCfgType is 'lmCcm', the destination MAC address is always a
multicast address indicating the level of the MEG: 01-80-c2-00-00-3y,
where y is the level of the MEG. An error is returned if this object
is set to any other value.
If jnxSoamLmCfgType is 'lmLmm' or 'lmSlm', the destination address is
the unicast address of the destination MEP. An error is returned if
this object is set to a multicast address.
This address will be used if the value of the object
mefSoamLmDestIsMepId is 'false'.
This object is only valid for the entity transmitting the
SOAM LM frames and is ignored by the entity receiving
SOAM LM frames.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R70, R104"
::= { jnxSoamLmCfgEntry 26 }
jnxSoamLmCfgStopTimeType OBJECT-TYPE
SYNTAX JnxSoamTcOperationTimeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the type of stop time to terminate the
SOAM LM session. The stop time can be forever (none), relative, or
fixed.
The value of 'none' indicates that the SOAM LM session never ends once it
has started unless it the session is disabled.
The value of 'immediate' is illegal and a write error will be returned
if this value is used.
The value of 'fixed' stops the SOAM LM session when the
jnxSoamLmFixedStopDateAndTime is less than or equal
to the current system date and time. This
value is used to implement an On-Demand fixed time PM session.
The value of 'relative' stops the SOAM LM session when the time
indicated by jnxSoamLmRelativeStopTime has passed since the session
start time as determined by the jnxSoamLmCfgStartTimeType,
jnxSoamLmCfgFixedStartDateAndTime and jnxSoamLmCfgRelativeStartTime
objects. This value is used to implement an On-Demand relative time
PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R3, R10, D2"
DEFVAL { none }
::= { jnxSoamLmCfgEntry 27 }
jnxSoamLmCfgFixedStopDateAndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the fixed stop date/time for the
SOAM Loss Measurement session. This object is used only used
if jnxSoamLmStopTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R10, R13"
DEFVAL { '0000010100000000'H }
::= { jnxSoamLmCfgEntry 28 }
jnxSoamLmCfgRelativeStopTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the relative stop time, from the
session start time, to stop the SOAM LM session. This
object is used only if jnxSoamLmStopTimeType is 'relative' and is
ignored otherwise.
object can only be written at row creation time 1922 and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R11"
DEFVAL { 0 }
::= { jnxSoamLmCfgEntry 29 }
jnxSoamLmCfgAvailabilityMeasurementInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..525600)
UNITS "minutes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the availability Measurement Interval in
minutes.
A Measurement Interval of 15 minutes is to be supported, other intervals
can be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R16, R17"
DEFVAL { 15 }
::= { jnxSoamLmCfgEntry 30 }
jnxSoamLmCfgAvailabilityNumConsecutiveMeasPdus OBJECT-TYPE
SYNTAX Unsigned32 (1..1000000)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies a configurable number of consecutive
loss measurement PDUs to be used in evaluating the
availability/unavailability status of each availability
indicator per MEF 10.2.1. Loss Measurement PDUs (LMMs, CCMs or
SLMs) are sent regularly with a period defined by
jnxSoamLmCfgMessagePeriod. Therefore, this object, when
multiplied by mefSoamLmCfgMessagePeriod, 2050 is equivalent to
is equivalent to the Availability parameter of 'delta_t' as
specified by MEF 10.2.1.
If the jnxSoamLmCfgType is lmLMM or lmCCM, this object defines the
number of LMM or CCM PDUs transmitted during each 'delta_t' period.
The Availability flr for a given 'delta_t' can be calculated based
on the counters in the last LMM/R or CCM during this 'delta_t' and
the last LMM/R or CCM in the previous 'delta_t'.
If the jnxSoamLmCfgType is lmSLM, this object defines the number
of SLM PDUs transmitted during each 'delta_t' period. The
Availability flr for a given 'delta_t' is calculated based on the
number of those SLM PDUs that are lost.
If the jnxSoamLmCfgType is lmLMM or lmCCM, the number range of 1
through 10 must be supported. The number range of 10 through 1000000
may be supported, but is not mandatory.
If the jnxSoamLmCfgType is lmSLM, the number range of 10 through
100 must be supported. The number range of 100 through 1000000
may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF 10.2.1] Section 7.9.8; [MEF SOAM-PM] R80, D33, R81"
DEFVAL { 10 }
::= { jnxSoamLmCfgEntry 31 }
jnxSoamLmCfgAvailabilityFlrThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies a configurable availability threshold to be
used in evaluating the availability/unavailability status of an
availability indicator per MEF 10.2.1. The availability threshold range
of 0.00 (0) through 1.00 (100000) is supported. This parameter is
equivalent to the Availability parameter of 'C' as specified by
MEF 10.2.1.
Units are in milli-percent, where 1 indicates 0.001 percent.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF 10.2.1] Section 7.9.8; [MEF SOAM-PM] R81, R82, D34"
DEFVAL { 50000 }
::= { jnxSoamLmCfgEntry 32 }
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals OBJECT-TYPE
SYNTAX Unsigned32 (1..1000)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies a configurable number of consecutive
availability indicators to be used to determine a change in the
availability status as indicated by MEF 10.2.1. This parameter is
equivalent to the Availability parameter of 'n' as specified
by MEF 10.2.1.
The number range of 1 through 10 must be supported. The number
range of 1 through 1000 may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF 10.2.1] Section 7.9.8; [MEF SOAM-PM] R80, D33"
DEFVAL { 10 }
::= { jnxSoamLmCfgEntry 33 }
jnxSoamLmCfgAvailabilityNumConsecutiveHighFlr OBJECT-TYPE
SYNTAX Unsigned32 (1..1000)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies a configurable number of consecutive
availability indicators to be used for assessing CHLI. This
parameter is equivalent to the Resilency parameter of 'p' as
specified by MEF 10.2.1.
jnxSoamLmCfgAvailabilityNumConsecutiveHighFlr must be strictly less than
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals. If not, the count of
high loss intervals over time, jnxSoamLmAvailabilityHighLoss, and the
count of consecutive high loss levels,
jnxSoamLmAvailabilityConsecutiveHighLoss, is disabled.
The number range of 1 through 10 must be supported. The number range
of 1 through 1000 may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF 10.2.1] Section 7.9.8; [MEF SOAM-PM] R86, D35, D36"
DEFVAL { 5 }
::= { jnxSoamLmCfgEntry 34 }
-- *****************************************************************************
-- Ethernet Loss Measurement Measured Statistic Table
-- *****************************************************************************
jnxSoamLmMeasuredStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamLmMeasuredStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object contains the last measured results for a SOAM Loss
Measurement session.
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Loss Measurement session is running.
Each object in this table applies only if the corresponding bit is set in
jnxSoamLmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot
or restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, 8D18"
::= { jnxSoamPmLmObjects 2 }
jnxSoamLmMeasuredStatsEntry OBJECT-TYPE
SYNTAX JnxSoamLmMeasuredStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamLmMeasuredStatsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamLmCfgIndex
}
::= { jnxSoamLmMeasuredStatsTable 1 }
JnxSoamLmMeasuredStatsEntry ::= SEQUENCE {
jnxSoamLmMeasuredStatsForwardFlr Unsigned32,
jnxSoamLmMeasuredStatsBackwardFlr Unsigned32,
jnxSoamLmMeasuredStatsAvailForwardStatus JnxSoamTcAvailabilityType,
jnxSoamLmMeasuredStatsAvailBackwardStatus JnxSoamTcAvailabilityType,
jnxSoamLmMeasuredStatsAvailForwardLastTransitionTime DateAndTime,
jnxSoamLmMeasuredStatsAvailBackwardLastTransitionTime DateAndTime
}
jnxSoamLmMeasuredStatsForwardFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the last frame loss ratio in the forward direction
calculated by this MEP. The FLR value
is a ratio that is expressed as a percent with a value of 0 (ratio
0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmMeasuredStatsEntry 1 }
jnxSoamLmMeasuredStatsBackwardFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the last frame loss ratio in the backward direction
calculated by this MEP. The FLR value
is a ratio that is expressed as a percent with a value of 0 (ratio
0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmMeasuredStatsEntry 2 }
jnxSoamLmMeasuredStatsAvailForwardStatus OBJECT-TYPE
SYNTAX JnxSoamTcAvailabilityType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability status (the outcome of the
last known availability indicator) in the forward direction.
Note that the status of an availability indicator is not known until
the loss for a number of subsequent availability indicators has been
calculated (as determined by
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals)
"
REFERENCE
"[MEF SOAM-PM] R83"
::= { jnxSoamLmMeasuredStatsEntry 3 }
jnxSoamLmMeasuredStatsAvailBackwardStatus OBJECT-TYPE
SYNTAX JnxSoamTcAvailabilityType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability status (the outcome of the
last availability indicator) in the backward direction.
Note that the status of an availability indicator is not known until
the loss for a number of subsequent availability indicators has been
calculated (as determined by
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals)
"
REFERENCE
"[MEF SOAM-PM] R83"
::= { jnxSoamLmMeasuredStatsEntry 4 }
jnxSoamLmMeasuredStatsAvailForwardLastTransitionTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the time of the last transition
between available and unavailable in the forward direction.
If there have been no transitions since the Loss Measurement
Session was started, this is set to 0.
"
REFERENCE
"[MEF SOAM-PM] R83"
::= { jnxSoamLmMeasuredStatsEntry 5 }
jnxSoamLmMeasuredStatsAvailBackwardLastTransitionTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the time of the last transition
between available and unavailable in the backward direction.
If there have been no transitions since the Loss Measurement
Session was started, this is set to 0.
"
REFERENCE
"[MEF SOAM-PM] R83"
::= { jnxSoamLmMeasuredStatsEntry 6 }
-- *****************************************************************************
-- Ethernet Loss Measurement Current Statistic Table
-- *****************************************************************************
jnxSoamLmCurrentStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamLmCurrentStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the results for the current Measurement
Interval in a SOAM Loss Measurement session gathered during the interval
indicated by iterator counts.
A row in this table is created automatically
by the SNMP Agent when the Loss Measurement session is configured.
Each row in the table represents the current statistics for a Loss
Measurement session for the defined MEP. This table uses four indices.
The first three indices are the indices of the Maintenance Domain, MaNet,
and MEP tables. The fourth index is the specific LM session on the
selected MEP. There may be more than one LM session per MEP. The
main use case for this is to allow multiple CoS instances to be
operating simultaneously for a MEP.
The objects in this table apply regardless of the value of
jnxSoamLmCfgType unless otherwise specified in the object description.
Except for jnxSoamLmCurrentStatsIndex, jnxSoamLmCurrentStatsStartTime,
jnxSoamLmCurrentStatsElapsedTime and jnxSoamLmCurrentStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamLmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or
restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, D9, D18"
::= { jnxSoamPmLmObjects 3 }
jnxSoamLmCurrentStatsEntry OBJECT-TYPE
SYNTAX JnxSoamLmCurrentStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamLmCurrentStatsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamLmCfgIndex
}
::= { jnxSoamLmCurrentStatsTable 1 }
JnxSoamLmCurrentStatsEntry ::= SEQUENCE {
jnxSoamLmCurrentStatsIndex Unsigned32,
jnxSoamLmCurrentStatsStartTime DateAndTime,
jnxSoamLmCurrentStatsElapsedTime TimeInterval,
jnxSoamLmCurrentStatsSuspect TruthValue,
jnxSoamLmCurrentStatsForwardTransmittedFrames Gauge32,
jnxSoamLmCurrentStatsForwardReceivedFrames Gauge32,
jnxSoamLmCurrentStatsForwardMinFlr Unsigned32,
jnxSoamLmCurrentStatsForwardMaxFlr Unsigned32,
jnxSoamLmCurrentStatsForwardAvgFlr Unsigned32,
jnxSoamLmCurrentStatsBackwardTransmittedFrames Gauge32,
jnxSoamLmCurrentStatsBackwardReceivedFrames Gauge32,
jnxSoamLmCurrentStatsBackwardMinFlr Unsigned32,
jnxSoamLmCurrentStatsBackwardMaxFlr Unsigned32,
jnxSoamLmCurrentStatsBackwardAvgFlr Unsigned32,
jnxSoamLmCurrentStatsSoamPdusSent Gauge32,
jnxSoamLmCurrentStatsSoamPdusReceived Gauge32
}
jnxSoamLmCurrentStatsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index for the current Measurement Interval for this
PM session. This value will become the value for
jnxSoamLmHistoryStatsIndex once the Measurement Interval
is completed.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.
"
::= { jnxSoamLmCurrentStatsEntry 1 }
jnxSoamLmCurrentStatsStartTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the current Measurement Interval started.
"
REFERENCE
"[MEF SOAM-PM] R22, R87, R112"
::= { jnxSoamLmCurrentStatsEntry 2 }
jnxSoamLmCurrentStatsElapsedTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the current Measurement Interval has been running, in 0.01
seconds.
"
REFERENCE
"[MEF SOAM-PM] R24, R87, R112"
::= { jnxSoamLmCurrentStatsEntry 3 }
jnxSoamLmCurrentStatsSuspect OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the Measurement Interval has been marked as suspect.
The object is set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
"
REFERENCE
"[MEF SOAM-PM] R39, R40, R41"
::= { jnxSoamLmCurrentStatsEntry 4 }
jnxSoamLmCurrentStatsForwardTransmittedFrames OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of frames transmitted in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmCurrentStatsEntry 5 }
jnxSoamLmCurrentStatsForwardReceivedFrames OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of frames received in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmCurrentStatsEntry 6 }
jnxSoamLmCurrentStatsForwardMinFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentStatsEntry 7 }
jnxSoamLmCurrentStatsForwardMaxFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentStatsEntry 8 }
jnxSoamLmCurrentStatsForwardAvgFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentStatsEntry 9 }
jnxSoamLmCurrentStatsBackwardTransmittedFrames OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of frames transmitted in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmCurrentStatsEntry 10 }
jnxSoamLmCurrentStatsBackwardReceivedFrames OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of frames received in the
backward direction by this MEP.
For a PM Session of type lmLmm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmCurrentStatsEntry 11 }
jnxSoamLmCurrentStatsBackwardMinFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentStatsEntry 12 }
jnxSoamLmCurrentStatsBackwardMaxFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentStatsEntry 13 }
jnxSoamLmCurrentStatsBackwardAvgFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentStatsEntry 14 }
jnxSoamLmCurrentStatsSoamPdusSent OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or
lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames
transmitted.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmCurrentStatsEntry 15 }
jnxSoamLmCurrentStatsSoamPdusReceived OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of SOAM PDUs
PDUs received in this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or
lmCcm. This object indicates the number of LMR, CCM, or SLR SOAM
frames received.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmCurrentStatsEntry 16 }
-- *****************************************************************************
-- Ethernet Loss Measurement Loss History Statistic Table
-- *****************************************************************************
jnxSoamLmHistoryStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamLmHistoryStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the results for history Measurement
Intervals in a SOAM Loss Measurement session.
Rows of this table object are created automatically
by the SNMP Agent when the Loss Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the history statistics for a Loss
Measurement session Measurement Interval for the defined MEP. This
table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific LM session on the selected MEP. The fifth index index the
specific Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval may be deleted (row deletion). If the measurement
interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
Except for jnxSoamLmHistoryStatsIndex, jnxSoamLmHistoryStatsEndTime,
jnxSoamLmHistoryStatsElapsedTime and jnxSoamLmHistoryStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamLmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, R21, D8, R25"
::= { jnxSoamPmLmObjects 4 }
jnxSoamLmHistoryStatsEntry OBJECT-TYPE
SYNTAX JnxSoamLmHistoryStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamLmHistoryStatsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamLmCfgIndex,
jnxSoamLmHistoryStatsIndex
}
::= { jnxSoamLmHistoryStatsTable 1 }
JnxSoamLmHistoryStatsEntry ::= SEQUENCE {
jnxSoamLmHistoryStatsIndex Unsigned32,
jnxSoamLmHistoryStatsEndTime DateAndTime,
jnxSoamLmHistoryStatsElapsedTime TimeInterval,
jnxSoamLmHistoryStatsSuspect TruthValue,
jnxSoamLmHistoryStatsForwardTransmittedFrames Gauge32,
jnxSoamLmHistoryStatsForwardReceivedFrames Gauge32,
jnxSoamLmHistoryStatsForwardMinFlr Unsigned32,
jnxSoamLmHistoryStatsForwardMaxFlr Unsigned32,
jnxSoamLmHistoryStatsForwardAvgFlr Unsigned32,
jnxSoamLmHistoryStatsBackwardTransmittedFrames Gauge32,
jnxSoamLmHistoryStatsBackwardReceivedFrames Gauge32,
jnxSoamLmHistoryStatsBackwardMinFlr Unsigned32,
jnxSoamLmHistoryStatsBackwardMaxFlr Unsigned32,
jnxSoamLmHistoryStatsBackwardAvgFlr Unsigned32,
jnxSoamLmHistoryStatsSoamPdusSent Gauge32,
jnxSoamLmHistoryStatsSoamPdusReceived Gauge32
}
jnxSoamLmHistoryStatsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index for the Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1. Measurement Intervals
for FLR (stored in this table) are based on
iterator count and are indexed independently
of Measurement Intervals for availability
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time.
"
::= { jnxSoamLmHistoryStatsEntry 1 }
jnxSoamLmHistoryStatsEndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the Measurement Interval ended.
"
REFERENCE
"[MEF SOAM-PM] R23, R87, R112"
::= { jnxSoamLmHistoryStatsEntry 2 }
jnxSoamLmHistoryStatsElapsedTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of time that the Measurement Interval ran for,
in 0.01 seconds.
"
REFERENCE
"[MEF SOAM-PM] R24, R87, R112"
::= { jnxSoamLmHistoryStatsEntry 3 }
jnxSoamLmHistoryStatsSuspect OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
"
REFERENCE
"[MEF SOAM-PM] R39, R40, R41, R42"
::= { jnxSoamLmHistoryStatsEntry 4 }
jnxSoamLmHistoryStatsForwardTransmittedFrames OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of frames transmitted in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of OAM
ETH-SLM frames only.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmHistoryStatsEntry 5 }
jnxSoamLmHistoryStatsForwardReceivedFrames OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of frames received in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of OAM
ETH-SLM frames only.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmHistoryStatsEntry 6 }
jnxSoamLmHistoryStatsForwardMinFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryStatsEntry 7 }
jnxSoamLmHistoryStatsForwardMaxFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryStatsEntry 8 }
jnxSoamLmHistoryStatsForwardAvgFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryStatsEntry 9 }
jnxSoamLmHistoryStatsBackwardTransmittedFrames OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of frames transmitted in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryStatsEntry 10 }
jnxSoamLmHistoryStatsBackwardReceivedFrames OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of frames received in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmHistoryStatsEntry 11 }
jnxSoamLmHistoryStatsBackwardMinFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] R69, R87, R112"
::= { jnxSoamLmHistoryStatsEntry 12 }
jnxSoamLmHistoryStatsBackwardMaxFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryStatsEntry 13 }
jnxSoamLmHistoryStatsBackwardAvgFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryStatsEntry 14 }
jnxSoamLmHistoryStatsSoamPdusSent OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm,
or lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames
transmitted.
"
REFERENCE
"[MEF SOAM-PM] R69, R87"
::= { jnxSoamLmHistoryStatsEntry 15 }
jnxSoamLmHistoryStatsSoamPdusReceived OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm,
or lmCcm. This object indicates the number of LMR, CCM, or SLR
SOAM frames received.
"
REFERENCE
"[MEF SOAM-PM] R69, R87"
::= { jnxSoamLmHistoryStatsEntry 16 }
-- *****************************************************************************
-- Ethernet Delay Measurement Configuration Table
-- *****************************************************************************
jnxSoamDmCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamDmCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table includes configuration objects and operations for the
Delay Measurement function.
Each row in the table represents a Delay Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP.
A Delay Measurement session is created on an existing MEP by first
accessing the jnxSoamDmOperNextIndex object and using this value as
the jnxSoamDmCfgIndex in the row creation.
Some writable objects in this table are only applicable in certain cases
(as described under each object), and attempts to write values for them
in other cases will be ignored.
The writable objects in this table need to be persistent upon reboot
or restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R50; [Y.1731]"
::= { jnxSoamPmDmObjects 1 }
jnxSoamDmCfgEntry OBJECT-TYPE
SYNTAX JnxSoamDmCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamDmCfgTable."
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamDmCfgIndex
}
::= { jnxSoamDmCfgTable 1 }
JnxSoamDmCfgEntry ::= SEQUENCE {
jnxSoamDmCfgIndex Unsigned32,
jnxSoamDmCfgType INTEGER,
jnxSoamDmCfgVersion Unsigned32,
jnxSoamDmCfgEnabled TruthValue,
jnxSoamDmCfgMeasurementEnable BITS,
jnxSoamDmCfgMessagePeriod Integer32,
jnxSoamDmCfgPriority IEEE8021PriorityValue,
jnxSoamDmCfgFrameSize Unsigned32,
jnxSoamDmCfgDataPattern JnxSoamTcDataPatternType,
jnxSoamDmCfgTestTlvIncluded TruthValue,
jnxSoamDmCfgTestTlvPattern JnxSoamTcTestPatternType,
jnxSoamDmCfgNumIntervalsStored Unsigned32,
jnxSoamDmCfgDestMepId Dot1agCfmMepIdOrZero,
jnxSoamDmCfgDestIsMepId TruthValue,
jnxSoamDmCfgStartTimeType JnxSoamTcOperationTimeType,
jnxSoamDmCfgRepetitionTime Unsigned32,
jnxSoamDmCfgAlignMeasurementIntervals TruthValue,
jnxSoamDmCfgInterFrameDelayVariationSelectionOffset Unsigned32,
jnxSoamDmCfgSessionType OCTET STRING,
jnxSoamDmCfgSessionStatus OCTET STRING,
jnxSoamDmCfgHistoryClear TruthValue,
jnxSoamDmCfgRowStatus RowStatus,
jnxSoamDmCfgMeasurementInterval Unsigned32,
jnxSoamDmCfgDestMacAddress MacAddress,
jnxSoamDmCfgSourceMacAddress MacAddress,
jnxSoamDmCfgFixedStartDateAndTime DateAndTime,
jnxSoamDmCfgRelativeStartTime TimeInterval,
jnxSoamDmCfgStopTimeType JnxSoamTcOperationTimeType,
jnxSoamDmCfgFixedStopDateAndTime DateAndTime,
jnxSoamDmCfgRelativeStopTime TimeInterval,
jnxSoamDmCfgAlignMeasurementOffset Unsigned32,
jnxSoamDmCfgNumMeasBinsPerFrameDelayInterval Unsigned32,
jnxSoamDmCfgNumMeasBinsPerInterFrameDelayVariationInterval Unsigned32,
jnxSoamDmCfgNumMeasBinsPerFrameDelayRangeInterval Unsigned32
}
jnxSoamDmCfgIndex
OBJECT-TYPE
SYNTAX Unsigned32(1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An index to the Delay Measurement Configuration table which indicates
the specific measurement session for the MEP.
jnxSoamPmMepOperNextIndex needs to be inspected to find an
available index for row-creation.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused for other PM sessions on the same MEP while this
session is active. The index value keeps increasing until it
wraps to zero. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused.
"
::= { jnxSoamDmCfgEntry 1 }
jnxSoamDmCfgType OBJECT-TYPE
SYNTAX INTEGER {
dmDmm (1),
dm1DmTx (2),
dm1DmRx (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates what type of Delay Measurement is to
be performed.
dmDmm(1) DMM SOAM PDU generated, DMR responses received
(one-way or two-way measurements)
dm1DmTx(2) 1DM SOAM PDU generated (one-way measurements are made by
the receiver)
dm1DmRx(3) 1DM SOAM PDU received and tracked (one-way measurements)
The exact PDUs to use are specified by this object in combination with
jnxSoamDmCfgVersion.
The value dmDMM is required. The values dm1DmTx and dm1DmRx are optional.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R52, R53, R54, O5, R88"
::= { jnxSoamDmCfgEntry 2 }
jnxSoamDmCfgVersion OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the version of the PDUs used to perform
Delay Measurement.
Version 0 indicates the PDU formats defined in Y.1731-2008.
Version 1 indicates the PDU formats defined in Y.1731-2011.
The exact PDUs to use are specified by this object in combination with
jnxSoamDmCfgType.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[Y.1731]"
DEFVAL { 0 }
::= { jnxSoamDmCfgEntry 3 }
jnxSoamDmCfgEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies whether the Delay Measurement session is
enabled.
The value 'true' indicates the Delay Measurement session is enabled AND
SOAM PDUs are sent and/or measurements are collected when the session
is running according to the scheduling objects (start time, stop time,
etc.).
The value 'false' indicates the Delay Measurement session is disabled
AND SOAM PDUs are not sent and/or measurements collected.
For a Delay Measurement session to be removed the row is deleted in
order to release internal resources.
This object can written/modified after row creation time.
If the DM session is enabled it resumes after shutdown/restart.
If the DM session is disabled the current Measurement Interval is
stopped, if it in process at the time, and all the in process calculations
for the partially completed Measurement Interval are finalized.
This object does not affect whether the single-ended Responder is
enabled or not, which is enabled or disabled by the
jnxSoamPmMepDmSingleEndedResponder object.
"
REFERENCE
"[MEF SOAM-PM] R4, R5, R6, O1, R12, R14"
DEFVAL { true }
::= { jnxSoamDmCfgEntry 4 }
jnxSoamDmCfgMeasurementEnable OBJECT-TYPE
SYNTAX BITS {
bSoamPdusSent(0),
bSoamPdusReceived(1),
bFrameDelayTwoWayBins(2),
bFrameDelayTwoWayMin(3),
bFrameDelayTwoWayMax(4),
bFrameDelayTwoWayAvg(5),
bFrameDelayForwardBins(6),
bFrameDelayForwardMin(7),
bFrameDelayForwardMax(8),
bFrameDelayForwardAvg(9),
bFrameDelayBackwardBins(10),
bFrameDelayBackwardMin(11),
bFrameDelayBackwardMax(12),
bFrameDelayBackwardAvg(13),
bIfdvForwardBins(14),
bIfdvForwardMin(15),
bIfdvForwardMax(16),
bIfdvForwardAvg(17),
bIfdvBackwardBins(18),
bIfdvBackwardMin(19),
bIfdvBackwardMax(20),
bIfdvBackwardAvg(21),
bIfdvTwoWayBins(22),
bIfdvTwoWayMin(23),
bIfdvTwoWayMax(24),
bIfdvTwoWayAvg(25),
bFrameDelayRangeForwardBins(26),
bFrameDelayRangeForwardMax(27),
bFrameDelayRangeForwardAvg(28),
bFrameDelayRangeBackwardBins(29),
bFrameDelayRangeBackwardMax(30),
bFrameDelayRangeBackwardAvg(31),
bFrameDelayRangeTwoWayBins(32),
bFrameDelayRangeTwoWayMax(33),
bFrameDelayRangeTwoWayAvg(34),
bMeasuredStatsFrameDelayTwoWay(35),
bMeasuredStatsFrameDelayForward(36),
bMeasuredStatsFrameDelayBackward(37),
bMeasuredStatsIfdvTwoWay(38),
bMeasuredStatsIfdvForward(39),
bMeasuredStatsIfdvBackward(40)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A vector of bits that indicates the type of SOAM DM counters that
are enabled.
A bit set to '1' enables the specific SOAM DM counter.
A bit set to '0' disables the SOAM DM counter.
If a particular SOAM DM counter is not supported the BIT value is
set to '0'.
Not all SOAM DM counters are supported for all SOAM DM types.
This object can only be written at row creation time and cannot be
modified once it has been created.
bSoamPdusSent(0)
Enables/disables the jnxSoamDmCurrentStatsSoamPdusSent
and jnxSoamDmHistoryStatsSoamPdusSent counters.
bSoamPdusReceived(1)
Enables/disables the jnxSoamDmCurrentStatsSoamPdusReceived
and jnxSoamDmHistoryStatsSoamPdusReceived counters.
bFrameDelayTwoWayBins(2)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayFrameDelay'.
bFrameDelayTwoWayMin(3)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayMin
and jnxSoamDmHistoryStatsFrameDelayTwoWayMin counters.
bFrameDelayTwoWayMax(4)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayMax
and jnxSoamDmHistoryStatsFrameDelayTwoWayMax counters.
bFrameDelayTwoWayAvg(5)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayAvg
and jnxSoamDmHistoryStatsFrameDelayTwoWayAvg counters.
bFrameDelayForwardBins(6)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardFrameDelay'.
bFrameDelayForwardMin(7)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardMin
and jnxSoamDmHistoryStatsFrameDelayForwardMin counters.
bFrameDelayForwardMax(8)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardMax
and jnxSoamDmHistoryStatsFrameDelayForwardMax counters.
bFrameDelayForwardAvg(9)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardAvg
and jnxSoamDmHistoryStatsFrameDelayForwardAvg counters.
bFrameDelayBackwardBins(10)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardFrameDelay'.
bFrameDelayBackwardMin(11)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardMin
and jnxSoamDmHistoryStatsFrameDelayBackwardMin counters.
bFrameDelayBackwardMax(12)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardMax
and jnxSoamDmHistoryStatsFrameDelayBackwardMax counters.
bFrameDelayBackwardAvg(13)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardAvg
and jnxSoamDmHistoryStatsFrameDelayBackwardAvg counters.
bIfdvForwardBins(14)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardIfdv'.
bIfdvForwardMin(15)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardMin
and jnxSoamDmHistoryStatsIfdvForwardMin counters.
bIfdvForwardMax(16)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardMax
and jnxSoamDmHistoryStatsIfdvForwardMax counters.
bIfdvForwardAvg(17)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardAvg
and jnxSoamDmHistoryStatsIfdvForwardAvg counters.
bIfdvBackwardBins(18)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardIfdv'.
bIfdvBackwardMin(19)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardMin
and jnxSoamDmHistoryStatsIfdvBackwardMin counters.
bIfdvBackwardMax(20)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardMax
and jnxSoamDmHistoryStatsIfdvBackwardMax counters.
bIfdvBackwardAvg(21)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardAvg
and jnxSoamDmHistoryStatsIfdvBackwardAvg counters.
bIfdvTwoWayBins(22)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayIfdv'.
bIfdvTwoWayMin(23)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayMin
and jnxSoamDmHistoryStatsIfdvTwoWayMin counters.
bIfdvTwoWayMax(24)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayMax
and jnxSoamDmHistoryStatsIfdvTwoWayMax counters.
bIfdvTwoWayAvg(25)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayAvg
and jnxSoamDmHistoryStatsIfdvTwoWayAvg counters.
bFrameDelayRangeForwardBins(26)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardFrameDelayRange'.
bFrameDelayRangeForwardMax(27)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeForwardMax
and jnxSoamDmHistoryStatsFrameDelayRangeForwardMax counters.
bFrameDelayRangeForwardAvg(28)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg
and jnxSoamDmHistoryStatsFrameDelayRangeForwardAvg counters.
bFrameDelayRangeBackwardBins(29)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardFrameDelayRange'.
bFrameDelayRangeBackwardMax(30)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax
and jnxSoamDmHistoryStatsFrameDelayRangeBackwardMax counters.
bFrameDelayRangeBackwardAvg(31)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg
and jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvg counters.
bFrameDelayRangeTwoWayBins(32)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayFrameDelayRange'.
bFrameDelayRangeTwoWayMax(33)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax
and jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMax counters.
bFrameDelayRangeTwoWayAvg(34)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg
and jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvg counters.
bMeasuredStatsFrameDelayTwoWay(35)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayTwoWay
counter.
bMeasuredStatsFrameDelayForward(36)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayForward
counter.
bMeasuredStatsFrameDelayBackward(37)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayBackward
counter.
bMeasuredStatsIfdvTwoWay(38)
Enables/disables the jnxSoamDmMeasuredStatsIfdvTwoWay
counter.
bMeasuredStatsIfdvForward(39)
Enables/disables the jnxSoamDmMeasuredStatsIfdvForward
counter.
bMeasuredStatsIfdvBackward(40)
Enables/disables the jnxSoamDmMeasuredStatsIfdvBackward
counter.
"
REFERENCE
"[MEF SOAM-PM]"
DEFVAL { { } }
::= { jnxSoamDmCfgEntry 5 }
jnxSoamDmCfgMessagePeriod OBJECT-TYPE
SYNTAX Integer32
UNITS "ms"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the interval between Delay Measurement
OAM message transmission. For Delay Measurement monitoring
applications, the default value is 100ms.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R61, R62, D22, R95, R96, D39"
DEFVAL { 100 }
::= { jnxSoamDmCfgEntry 6 }
jnxSoamDmCfgPriority OBJECT-TYPE
SYNTAX IEEE8021PriorityValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the priority of frames with
Delay Measurement OAM message information.
The default value is to be the value which yields the lowest frame
loss.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R1, R2, R56, D21, R57, R58, R90-R94, D28;
[MEF 10.2.1] Section 6.8"
::= { jnxSoamDmCfgEntry 7 }
jnxSoamDmCfgFrameSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the Delay Measurement frame size between
64 bytes and the maximum transmission unit of the EVC.
The range of frame sizes from 64 through 2000 octets need to be
supported, and the range of frame sizes from 2001 through 9600 octets
is suggested to be supported.
The adjustment to the frame size of the standard frame size is
accomplished by the addition of a Data or Test TLV. A Data or Test TLV
is only added to the frame if the frame size is greater than 64 bytes.
This object is only valid for the entity transmitting the Delay
Measurement frames (dmDmm, dm1DmTx) and is ignored by the entity
receiving frames.
In addition, this object is not valid when jnxSoamDmCfgVersion is 0.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R63, R64, D23, D24, R97, R98, D40, D41"
DEFVAL { 64 }
::= { jnxSoamDmCfgEntry 8 }
jnxSoamDmCfgDataPattern OBJECT-TYPE
SYNTAX JnxSoamTcDataPatternType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the DM data pattern included in a Data TLV
when the size of the DM frame is determined by the
jnxSoamDmFrameSize object and jnxSoamDmTestTlvIncluded is 'false'.
If the frame size object does not define the DM frame size or
jnxSoamDmTestTlvIncluded is 'true' the value of this object is
ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
DEFVAL { zeroPattern }
::= { jnxSoamDmCfgEntry 9 }
jnxSoamDmCfgTestTlvIncluded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether a Test TLV or Data TLV is included when the size
of the DM frame is determined by the jnxSoamDmFrameSize object.
A value of 'true' indicates that the Test TLV is to be included. A
value of 'false' indicates that the Data TLV is to be included.
If the frame size object does not define the DM frame size
the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[Y.1731] 9.3"
DEFVAL { false }
::= { jnxSoamDmCfgEntry 10 }
jnxSoamDmCfgTestTlvPattern OBJECT-TYPE
SYNTAX JnxSoamTcTestPatternType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the type of test pattern to be
sent in the DM frame Test TLV when the size
of DM PDU is determined by the jnxSoamDmFrameSize object and
jnxSoamDmTestTlvIncluded is 'true'. If the frame size object
does not define the DM frame size or jnxSoamDmTestTlvIncluded
is 'false' the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
DEFVAL { null }
::= { jnxSoamDmCfgEntry 11 }
jnxSoamDmCfgNumIntervalsStored OBJECT-TYPE
SYNTAX Unsigned32 (1..1000)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the number of completed Measurement Intervals
to store in the history statistic table.
At least 32 completed Measurement Intervals are to be stored. 96
Measurement Intervals are recommended to be stored.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R21, D8, D9"
DEFVAL { 32 }
::= { jnxSoamDmCfgEntry 12 }
jnxSoamDmCfgDestMepId OBJECT-TYPE
SYNTAX Dot1agCfmMepIdOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Maintenance Association End Point Identifier of
another MEP in the same Maintenance Association to which
the SOAM DM frame is to be sent.
This address will be used if the value of the column
jnxSoamDmDestIsMepId is 'true'. A value of zero
means that the destination MEP ID has not been configured.
This object is only valid for the entity transmitting the Delay
Measurement frames, types 'dmDmm' and 'dm1DmTx'. It is not applicable
for the 'dm1DmRx' type.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R55, R89"
DEFVAL { 0 }
::= { jnxSoamDmCfgEntry 13 }
jnxSoamDmCfgDestIsMepId OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A value of 'true' indicates that MEPID of the target MEP is used for
SOAM DM frame transmission.
A value of 'false' indicates that the destination MAC address of the
target MEP is used for SOAM DM frame transmission.
This object is only valid for the entity transmitting the Delay
Measurement frames, types 'dmDmm' and 'dm1DmTx'. It is not applicable
for the 'dm1DmRx type.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R55, R89"
DEFVAL { true }
::= { jnxSoamDmCfgEntry 14 }
jnxSoamDmCfgStartTimeType OBJECT-TYPE
SYNTAX JnxSoamTcOperationTimeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the type of start time of the SOAM DM
session. The start time can be disabled (none), immediate, relative,
or fixed.
The value of 'none' is illegal and a write error will be returned
if this value is used.
The value of 'immediate' starts the SOAM DM session when the
jnxSoamDmCfgEnabled is true.
The value of 'fixed' starts the SOAM DM session when the
jnxSoamDmFixedStartDateAndTime is less than or equal to the current
system date and time and jnxSoamDmCfgEnabled is true. This value is used
to implement an On-Demand fixed time PM session.
The value of 'relative' starts the SOAM DM session when the current
system date and time minus the jnxSoamDmRelativeStartTime is greater than
or equal to the system date and time when the jnxSoamDmStartTimeType
object was written and jnxSoamDmCfgEnabled is true. This value is used
to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R3, R7, R8, D1"
DEFVAL { immediate }
::= { jnxSoamDmCfgEntry 15 }
jnxSoamDmCfgRepetitionTime OBJECT-TYPE
SYNTAX Unsigned32 (0..31536000)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies a configurable repetition time between
Measurement Intervals in a Delay Measurement session in seconds.
If the value is 0 (none), there is no time gap between the end of one
Measurement Interval and the start of a new Measurement Interval.
This is the normal usage case.
If the value is greater than one Measurement Interval there is time gap
between the end of one Measurement Interval and the start of the next
Measurement Interval. The repetition time specifies the time between
the start of consecutive Measurement Intervals; hence the gap between
the end of one Measurement Interval and the start of the next is equal
to the difference between the repetition time and the measurement
interval. During this gap, no SOAM PDUs are sent for this session and
no measurements are made.
If the value is greater 0 but less than or equal to the measurement
interval, an error is returned.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R18, D3, R19, R20"
DEFVAL { 0 }
::= { jnxSoamDmCfgEntry 16 }
jnxSoamDmCfgAlignMeasurementIntervals OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies whether the Measurement Intervals for
the Delay Measurement session are aligned with a zero offset to
real time.
The value 'true' indicates that each Measurement Interval starts
at a time which is aligned to NE time source hour, if the repetition
time (or the Measurement Interval, if the repetition time is 0) is
a factor of an hour, i.e. 60min/15min = 4. For instance, a
Measurement Interval/Repetition Time of 15 minutes would stop/start
the Measurement Interval at 0, 15, 30, and 45 minutes of an hour. A
Measurement Interval/Repetition Time of 7 minutes would not align
to the hour since 7 minutes is NOT a factor of an hour, i.e.
60min/7min = 8.6. In this case the behavior is the same as if the
object is set to 'false'.
The value 'false' indicates that the first Measurement Interval starts
at an arbitrary time and each subsequent Measurement Interval starts
at a time which is determined by jnxSoamLmCfgRepetitionTime.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] D4, D5, D6"
DEFVAL { true }
::= { jnxSoamDmCfgEntry 17 }
jnxSoamDmCfgInterFrameDelayVariationSelectionOffset OBJECT-TYPE
SYNTAX Unsigned32 (1..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the selection offset for
Inter-Frame Delay Variation measurements. If this value
is set to n, then the IFDV is calculated by taking the
difference in frame delay between frame F and frame (F+n).
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] O4, D25, O6, D42"
DEFVAL { 1 }
::= { jnxSoamDmCfgEntry 18 }
jnxSoamDmCfgSessionType OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1..42))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the current session is defined to
be 'Proactive' or 'On-Demand'. A value of 'proactive'
indicates the current session is 'Proactive'. A value of 'onDemand'
indicates the current session is 'On-Demand'.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R3"
DEFVAL { "proactive" }
::= { jnxSoamDmCfgEntry 19 }
jnxSoamDmCfgSessionStatus OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(1..42))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current status of the DM session. A value
of 'active' indicates the current DM session is active, i.e. the current
time lies between the start time and the stop time, and
jnxSoamDmCfgEnabled is true. A value of 'notActive' indicates the
current DM session is not active, i.e. it has not started yet, has
stopped upon reaching the stop time, or is disabled.
"
::= { jnxSoamDmCfgEntry 20 }
jnxSoamDmCfgHistoryClear OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object when written clears the Delay Measurement history
tables (jnxSoamDmHistoryStatsTable)
- all rows are deleted. When read the value always returns 'false'.
Writing this value does not change the current stat table,
nor any of the items in the configuration table.
Writing this object at row creation has no effect.
"
DEFVAL { false }
::= { jnxSoamDmCfgEntry 21 }
jnxSoamDmCfgRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the row.
The writable columns in a row cannot be changed if the row
is active, except for jnxSoamDmCfgEnabled and jnxSoamDmCfgHistoryClear
objects. All columns are to have a valid value before a row
can be activated.
"
::= { jnxSoamDmCfgEntry 22 }
jnxSoamDmCfgMeasurementInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..1440)
UNITS "minutes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies a Measurement Interval in minutes.
A Measurement Interval 15 minutes needs to be supported, other intervals
may be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R16, R17"
DEFVAL { 15 }
::= { jnxSoamDmCfgEntry 23 }
jnxSoamDmCfgDestMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Target or Destination MAC Address Field to be transmitted.
If mefSoamDmCfgType is 'dmDmm', the destination address is to be the
unicast address of the destination MEP. An error is returned if this
object is set to a multicast address.
If mefSoamDmCfgType is 'dm1DmTx', the destination address is normally the
unicast address of the destination MEP, but can be a multicast address
indicating the level of the MEG: 01-80-c2-00-00-3y, where y is the
level of the MEG. An error is returned if this object is set to any
other multicast address.
If mefSoamDmCfgType is 'dm1DmRx', this object is ignored.
This address will be used if the value of the object
mefSoamDmDestIsMepId is 'false'.
This object is only valid for the entity transmitting the
SOAM DM frames and is ignored by the entity receiving
SOAM DM frames.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R55, R89"
::= { jnxSoamDmCfgEntry 24 }
jnxSoamDmCfgSourceMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Source MAC Address Field of the received SOAM DM session PDUs.
If mefSoamDmCfgType is dm1DmRx this object indicates the source
address of the dm1DmTx DM session.
This object is only valid for mefSoamDmCfgType set to dm1DmRx. It is
ignored for mefSoamDmCfgType set to dmDmm or dm1DmTx.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R55, R89"
::= { jnxSoamDmCfgEntry 25 }
jnxSoamDmCfgFixedStartDateAndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the fixed start date/time for the
SOAM Delay Measurement session. This object is used only used if
mefSoamDmStartTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R9"
DEFVAL { '0000010100000000'H }
::= { jnxSoamDmCfgEntry 26 }
jnxSoamDmCfgRelativeStartTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the relative start time, from
the current system time, for the SOAM DM session. This
object is used only if mefSoamDmStartTimeType is 'relative'
and is ignored otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R9"
DEFVAL { 0 }
::= { jnxSoamDmCfgEntry 27 }
jnxSoamDmCfgStopTimeType OBJECT-TYPE
SYNTAX JnxSoamTcOperationTimeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the type of stop time to terminate the
SOAM DM session. The stop time can be forever (none), relative, or
fixed.
The value of 'none' indicates that the SOAM DM session never ends once it
has started unless the session is disabled.
The value of 'immediate' is illegal and a write error will be returned
if this value is used.
The value of 'fixed' stops the SOAM DM session when the
mefSoamDmFixedStopDateAndTime is less than or equal
to the current system date. This
value is used to implement an On-Demand fixed time PM session.
The value of 'relative' stops the SOAM DM session when the time
indicated by mefSoamDmRelativeStopTime has passed since the session
start time as determined by the mefSoamDmCfgStartTimeType,
mefSoamDmCfgFixedStartDateAndTime and mefSoamDmCfgRelativeStartTime
objects.
This value is used to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R3, R10, D2"
DEFVAL { none }
::= { jnxSoamDmCfgEntry 28 }
jnxSoamDmCfgFixedStopDateAndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the fixed stop date/time for the
SOAM Delay Measurement session. This object is used only used
if mefSoamDmStopTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R10, R13"
DEFVAL { '0000010100000000'H }
::= { jnxSoamDmCfgEntry 29 }
jnxSoamDmCfgRelativeStopTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the relative stop time, from the
session start time, to stop the SOAM DM session. This
object is used only if mefSoamDmStopTimeType is 'relative' and is
otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R11"
DEFVAL { 0 }
::= { jnxSoamDmCfgEntry 30 }
jnxSoamDmCfgAlignMeasurementOffset OBJECT-TYPE
SYNTAX Unsigned32 (0..525600)
UNITS "minutes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the offset in minutes from the time of day value
if mefSoamDmCfgAlignMeasurementIntervals is 'true' and the repetition
time is a factor of 60 minutes. If not, the value of this object
is ignored.
If the Measurement Interval is 15 minutes and
mefSoamDmCfgAlignMeasurementIntervals is true and if this object was
set to 5 minutes, the Measurement Intervals would start at 5, 20, 35, 50
minutes past each hour.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] D7"
DEFVAL { 0 }
::= { jnxSoamDmCfgEntry 31 }
jnxSoamDmCfgNumMeasBinsPerFrameDelayInterval OBJECT-TYPE
SYNTAX Unsigned32 (2..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the number of measurement bins
per Measurement Interval for Frame Delay measurements.
At least 3 bins are to be supported; at least 10 bins are recommended
to be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R27, D11, R28, D12"
DEFVAL { 3 }
::= { jnxSoamDmCfgEntry 32 }
jnxSoamDmCfgNumMeasBinsPerInterFrameDelayVariationInterval OBJECT-TYPE
SYNTAX Unsigned32 (2..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the number of measurement bins
per Measurement Interval for Inter-Frame Delay Variation
measurements.
The minimum number of measurement bins to be supported is 2. The
supported is 10.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R29, D13, R30, D14"
DEFVAL { 2 }
::= { jnxSoamDmCfgEntry 33 }
jnxSoamDmCfgNumMeasBinsPerFrameDelayRangeInterval OBJECT-TYPE
SYNTAX Unsigned32 (2..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the number of measurement bins
per Measurement Interval for Frame Delay Range measurements.
At least 2 bins are to be supported; at least 10 bins are recommended
to be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.
"
REFERENCE
"[MEF SOAM-PM] R31, D15, R32, D16"
DEFVAL { 2 }
::= { jnxSoamDmCfgEntry 34 }
-- *****************************************************************************
-- Ethernet Delay Measurement Measured Statistic Table
-- *****************************************************************************
jnxSoamDmMeasuredStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamDmMeasuredStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object contains the last measured results for a SOAM Delay
Measurement session.
Each row in the table represents a Delay Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Delay Measurement session is running.
Each object in this table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or restart
of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, D18"
::= { jnxSoamPmDmObjects 2 }
jnxSoamDmMeasuredStatsEntry OBJECT-TYPE
SYNTAX JnxSoamDmMeasuredStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamDmMeasuredStatsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamDmCfgIndex
}
::= { jnxSoamDmMeasuredStatsTable 1 }
JnxSoamDmMeasuredStatsEntry ::= SEQUENCE {
jnxSoamDmMeasuredStatsFrameDelayTwoWay Unsigned32,
jnxSoamDmMeasuredStatsFrameDelayForward Unsigned32,
jnxSoamDmMeasuredStatsFrameDelayBackward Unsigned32,
jnxSoamDmMeasuredStatsIfdvTwoWay Unsigned32,
jnxSoamDmMeasuredStatsIfdvForward Unsigned32,
jnxSoamDmMeasuredStatsIfdvBackward Unsigned32
}
jnxSoamDmMeasuredStatsFrameDelayTwoWay OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the two-way frame delay calculated by this
MEP from the last received SOAM PDU.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmMeasuredStatsEntry 1 }
jnxSoamDmMeasuredStatsFrameDelayForward OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the frame delay in the forward direction
calculated by this MEP from the last received SOAM PDU. The value of this
object may not be accurate in the absence of sufficiently precise clock
synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmMeasuredStatsEntry 2 }
jnxSoamDmMeasuredStatsFrameDelayBackward OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the frame delay in the backward direction
calculated by this MEP from the last received SOAM PDU. The value of this
object may not be accurate in the absence of sufficiently precise clock
synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmMeasuredStatsEntry 3 }
jnxSoamDmMeasuredStatsIfdvTwoWay OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the last two-way inter-frame delay
interval calculated by this MEP.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmMeasuredStatsEntry 4 }
jnxSoamDmMeasuredStatsIfdvForward OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the last one-way inter-frame delay
interval in the forward direction calculated by this MEP.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmMeasuredStatsEntry 5 }
jnxSoamDmMeasuredStatsIfdvBackward OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the last one-way inter-frame delay
interval in the backward direction calculated by this MEP.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmMeasuredStatsEntry 6 }
-- *****************************************************************************
-- Ethernet Delay Measurement Current Statistic Table
-- *****************************************************************************
jnxSoamDmCurrentStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamDmCurrentStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the results for the current Measurement
Interval in a SOAM Delay Measurement session gathered during the interval
indicated by iterator count.
A row in this table is created automatically
by the SNMP Agent when the Delay Measurement session is configured.
Each row in the table represents the current statistics for a Delay
Measurement session for the defined MEP. This table uses four indices.
The first three indices are the indices of the Maintenance Domain, MaNet,
and MEP tables. The fourth index is the specific DM session on the
selected MEP. There can be more than one DM session per MEP.
The objects in this table apply regardless of the value of
jnxSoamDmCfgType unless otherwise specified in the object description.
Backward and two-way statistic objects are undefined if jnxSoamDmCfgType
is dm1DmRx.
Except for jnxSoamDmCurrentStatsIndex, jnxSoamDmCurrentStatsStartTime
jnxSoamDmCurrentStatsElapsedTime and jnxSoamDmCurrentStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or
restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, D9, D18"
::= { jnxSoamPmDmObjects 3 }
jnxSoamDmCurrentStatsEntry OBJECT-TYPE
SYNTAX JnxSoamDmCurrentStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamDmCurrentStatsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamDmCfgIndex
}
::= { jnxSoamDmCurrentStatsTable 1 }
JnxSoamDmCurrentStatsEntry ::= SEQUENCE {
jnxSoamDmCurrentStatsIndex Unsigned32,
jnxSoamDmCurrentStatsStartTime DateAndTime,
jnxSoamDmCurrentStatsElapsedTime TimeInterval,
jnxSoamDmCurrentStatsSuspect TruthValue,
jnxSoamDmCurrentStatsFrameDelayTwoWayMin Unsigned32,
jnxSoamDmCurrentStatsFrameDelayTwoWayMax Unsigned32,
jnxSoamDmCurrentStatsFrameDelayTwoWayAvg Unsigned32,
jnxSoamDmCurrentStatsFrameDelayForwardMin Unsigned32,
jnxSoamDmCurrentStatsFrameDelayForwardMax Unsigned32,
jnxSoamDmCurrentStatsFrameDelayForwardAvg Unsigned32,
jnxSoamDmCurrentStatsFrameDelayBackwardMin Unsigned32,
jnxSoamDmCurrentStatsFrameDelayBackwardMax Unsigned32,
jnxSoamDmCurrentStatsFrameDelayBackwardAvg Unsigned32,
jnxSoamDmCurrentStatsIfdvForwardMin Unsigned32,
jnxSoamDmCurrentStatsIfdvForwardMax Unsigned32,
jnxSoamDmCurrentStatsIfdvForwardAvg Unsigned32,
jnxSoamDmCurrentStatsIfdvBackwardMin Unsigned32,
jnxSoamDmCurrentStatsIfdvBackwardMax Unsigned32,
jnxSoamDmCurrentStatsIfdvBackwardAvg Unsigned32,
jnxSoamDmCurrentStatsIfdvTwoWayMin Unsigned32,
jnxSoamDmCurrentStatsIfdvTwoWayMax Unsigned32,
jnxSoamDmCurrentStatsIfdvTwoWayAvg Unsigned32,
jnxSoamDmCurrentStatsSoamPdusSent Gauge32,
jnxSoamDmCurrentStatsSoamPdusReceived Gauge32,
jnxSoamDmCurrentStatsFrameDelayRangeForwardMax Unsigned32,
jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg Unsigned32,
jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax Unsigned32,
jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg Unsigned32,
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax Unsigned32,
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg Unsigned32
}
jnxSoamDmCurrentStatsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index for the current Measurement Interval for this
PM session. This value will become the value for
jnxSoamDmHistoryStatsIndex once the Measurement Interval
is completed.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.
"
::= { jnxSoamDmCurrentStatsEntry 1 }
jnxSoamDmCurrentStatsStartTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the current Measurement Interval started.
"
REFERENCE
"[MEF SOAM-PM] R22, R66, R100"
::= { jnxSoamDmCurrentStatsEntry 2 }
jnxSoamDmCurrentStatsElapsedTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the current Measurement Interval has been running, in 0.01
seconds.
"
REFERENCE
"[MEF SOAM-PM] R24, R66, R100"
::= { jnxSoamDmCurrentStatsEntry 3 }
jnxSoamDmCurrentStatsSuspect OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the Measurement Interval has been marked as suspect.
The object is to be set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
"
REFERENCE
"[MEF SOAM-PM] R39, R40, R41"
::= { jnxSoamDmCurrentStatsEntry 4 }
jnxSoamDmCurrentStatsFrameDelayTwoWayMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmCurrentStatsEntry 5 }
jnxSoamDmCurrentStatsFrameDelayTwoWayMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmCurrentStatsEntry 6 }
jnxSoamDmCurrentStatsFrameDelayTwoWayAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmCurrentStatsEntry 7 }
jnxSoamDmCurrentStatsFrameDelayForwardMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R67, R101"
::= { jnxSoamDmCurrentStatsEntry 8 }
jnxSoamDmCurrentStatsFrameDelayForwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R67, R101"
::= { jnxSoamDmCurrentStatsEntry 9 }
jnxSoamDmCurrentStatsFrameDelayForwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R67, R101"
::= { jnxSoamDmCurrentStatsEntry 10 }
jnxSoamDmCurrentStatsFrameDelayBackwardMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R67"
::= { jnxSoamDmCurrentStatsEntry 11 }
jnxSoamDmCurrentStatsFrameDelayBackwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R67"
::= { jnxSoamDmCurrentStatsEntry 12 }
jnxSoamDmCurrentStatsFrameDelayBackwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R67"
::= { jnxSoamDmCurrentStatsEntry 13 }
jnxSoamDmCurrentStatsIfdvForwardMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmCurrentStatsEntry 14 }
jnxSoamDmCurrentStatsIfdvForwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmCurrentStatsEntry 15 }
jnxSoamDmCurrentStatsIfdvForwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmCurrentStatsEntry 16 }
jnxSoamDmCurrentStatsIfdvBackwardMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmCurrentStatsEntry 17 }
jnxSoamDmCurrentStatsIfdvBackwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmCurrentStatsEntry 18 }
jnxSoamDmCurrentStatsIfdvBackwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmCurrentStatsEntry 19 }
jnxSoamDmCurrentStatsIfdvTwoWayMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmCurrentStatsEntry 20 }
jnxSoamDmCurrentStatsIfdvTwoWayMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmCurrentStatsEntry 21 }
jnxSoamDmCurrentStatsIfdvTwoWayAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmCurrentStatsEntry 22 }
jnxSoamDmCurrentStatsSoamPdusSent OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamDmCfgType is dmDmm or dm1DmTx and
is undefined if jnxSoamDmCfgType is dm1DmRx. It indicates the
number of DMM or 1DM SOAM frames transmitted.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmCurrentStatsEntry 23 }
jnxSoamDmCurrentStatsSoamPdusReceived OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object indicates the number of DMR and 1DM SOAM frames
received. This object applies when jnxSoamDmCfgTypeis dmDmm or
dm1DmRx and is undefined if jnxSoamDmCfgTypeis dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmCurrentStatsEntry 24 }
jnxSoamDmCurrentStatsFrameDelayRangeForwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame delay range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmCurrentStatsEntry 25 }
jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame delay range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmCurrentStatsEntry 26 }
jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame delay range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmCurrentStatsEntry 27 }
jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame delay range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmCurrentStatsEntry 28 }
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum two-way frame delay range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmCurrentStatsEntry 29 }
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average two-way frame delay range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmCurrentStatsEntry 30 }
-- *****************************************************************************
-- Ethernet Delay Measurement History Statistic Table
-- *****************************************************************************
jnxSoamDmHistoryStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamDmHistoryStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the results for history Measurement
Intervals in a SOAM Delay Measurement session.
Rows of this table are created automatically
by the SNMP Agent when the Delay Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the Measurement Interval history
statistics for a Delay Measurement session for the defined MEP. This
table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific DM session on the selected MEP. The fifth index is the
Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval can be deleted (row deletion). If the measurement
interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
The objects in this table apply regardless of the value of
jnxSoamDmCfgType unless otherwise specified in the object description.
Backward and two-way statistic objects are undefined if jnxSoamDmCfgType
is dm1DmRx.
Except for jnxSoamDmHistoryStatsIndex, jnxSoamDmHistoryStatsEndTime,
jnxSoamDmHistoryStatsElapsedTime and jnxSoamDmHistoryStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, R21, D8, R25"
::= { jnxSoamPmDmObjects 4 }
jnxSoamDmHistoryStatsEntry OBJECT-TYPE
SYNTAX JnxSoamDmHistoryStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamDmHistoryStatsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamDmCfgIndex,
jnxSoamDmHistoryStatsIndex
}
::= { jnxSoamDmHistoryStatsTable 1 }
JnxSoamDmHistoryStatsEntry ::= SEQUENCE {
jnxSoamDmHistoryStatsIndex Unsigned32,
jnxSoamDmHistoryStatsEndTime DateAndTime,
jnxSoamDmHistoryStatsElapsedTime TimeInterval,
jnxSoamDmHistoryStatsSuspect TruthValue,
jnxSoamDmHistoryStatsFrameDelayTwoWayMin Unsigned32,
jnxSoamDmHistoryStatsFrameDelayTwoWayMax Unsigned32,
jnxSoamDmHistoryStatsFrameDelayTwoWayAvg Unsigned32,
jnxSoamDmHistoryStatsFrameDelayForwardMin Unsigned32,
jnxSoamDmHistoryStatsFrameDelayForwardMax Unsigned32,
jnxSoamDmHistoryStatsFrameDelayForwardAvg Unsigned32,
jnxSoamDmHistoryStatsFrameDelayBackwardMin Unsigned32,
jnxSoamDmHistoryStatsFrameDelayBackwardMax Unsigned32,
jnxSoamDmHistoryStatsFrameDelayBackwardAvg Unsigned32,
jnxSoamDmHistoryStatsIfdvForwardMin Unsigned32,
jnxSoamDmHistoryStatsIfdvForwardMax Unsigned32,
jnxSoamDmHistoryStatsIfdvForwardAvg Unsigned32,
jnxSoamDmHistoryStatsIfdvBackwardMin Unsigned32,
jnxSoamDmHistoryStatsIfdvBackwardMax Unsigned32,
jnxSoamDmHistoryStatsIfdvBackwardAvg Unsigned32,
jnxSoamDmHistoryStatsIfdvTwoWayMin Unsigned32,
jnxSoamDmHistoryStatsIfdvTwoWayMax Unsigned32,
jnxSoamDmHistoryStatsIfdvTwoWayAvg Unsigned32,
jnxSoamDmHistoryStatsSoamPdusSent Gauge32,
jnxSoamDmHistoryStatsSoamPdusReceived Gauge32,
jnxSoamDmHistoryStatsFrameDelayRangeForwardMax Unsigned32,
jnxSoamDmHistoryStatsFrameDelayRangeForwardAvg Unsigned32,
jnxSoamDmHistoryStatsFrameDelayRangeBackwardMax Unsigned32,
jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvg Unsigned32,
jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMax Unsigned32,
jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvg Unsigned32
}
jnxSoamDmHistoryStatsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index for the Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time.
"
::= { jnxSoamDmHistoryStatsEntry 1 }
jnxSoamDmHistoryStatsEndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the Measurement Interval ended.
"
REFERENCE
"[MEF SOAM-PM] R23, R66, R100"
::= { jnxSoamDmHistoryStatsEntry 2 }
jnxSoamDmHistoryStatsElapsedTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of time that the Measurement Interval ran for,
in 0.01 seconds.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 3 }
jnxSoamDmHistoryStatsSuspect OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
"
REFERENCE
"[MEF SOAM-PM] R39, R40, R41, R42"
::= { jnxSoamDmHistoryStatsEntry 4 }
jnxSoamDmHistoryStatsFrameDelayTwoWayMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 5 }
jnxSoamDmHistoryStatsFrameDelayTwoWayMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 6 }
jnxSoamDmHistoryStatsFrameDelayTwoWayAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 7 }
jnxSoamDmHistoryStatsFrameDelayForwardMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 8 }
jnxSoamDmHistoryStatsFrameDelayForwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 9 }
jnxSoamDmHistoryStatsFrameDelayForwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 10 }
jnxSoamDmHistoryStatsFrameDelayBackwardMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 11 }
jnxSoamDmHistoryStatsFrameDelayBackwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 12 }
jnxSoamDmHistoryStatsFrameDelayBackwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 13 }
jnxSoamDmHistoryStatsIfdvForwardMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 14 }
jnxSoamDmHistoryStatsIfdvForwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 15 }
jnxSoamDmHistoryStatsIfdvForwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 16 }
jnxSoamDmHistoryStatsIfdvBackwardMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 17 }
jnxSoamDmHistoryStatsIfdvBackwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 18 }
jnxSoamDmHistoryStatsIfdvBackwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 19 }
jnxSoamDmHistoryStatsIfdvTwoWayMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmHistoryStatsEntry 20 }
jnxSoamDmHistoryStatsIfdvTwoWayMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmHistoryStatsEntry 21 }
jnxSoamDmHistoryStatsIfdvTwoWayAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmHistoryStatsEntry 22 }
jnxSoamDmHistoryStatsSoamPdusSent OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamDmCfgType is dmDmm or dm1DmTx and
is undefined if jnxSoamDmCfgType is dm1DmRx. It indicates the
number of DMM or 1DM SOAM frames transmitted.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 23 }
jnxSoamDmHistoryStatsSoamPdusReceived OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object indicates the number of DMR and 1DM SOAM frames
received. This object applies when jnxSoamDmCfgType is dmDmm or
dm1DmRx and is undefined if jnxSoamDmCfgType is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 24 }
jnxSoamDmHistoryStatsFrameDelayRangeForwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way Frame Delay Range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 25 }
jnxSoamDmHistoryStatsFrameDelayRangeForwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way Frame Delay Range
in the forward direction calculated by this MEP for this
Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.
"
REFERENCE
"[MEF SOAM-PM] R66, R100"
::= { jnxSoamDmHistoryStatsEntry 26 }
jnxSoamDmHistoryStatsFrameDelayRangeBackwardMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way Frame Delay Range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 27 }
jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way Frame Delay Range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
REFERENCE
"[MEF SOAM-PM] R66"
::= { jnxSoamDmHistoryStatsEntry 28 }
jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum two-way Frame Delay Range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmHistoryStatsEntry 29 }
jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvg OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average two-way Frame Delay Range
Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.
"
::= { jnxSoamDmHistoryStatsEntry 30 }
-- *****************************************************************************
-- Performance Measurement Loss Threshold Configuration Table
-- *****************************************************************************
jnxSoamLmThresholdCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamLmThresholdCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the list of Loss Measurement configuration threshold
values for LM Performance Monitoring.
The main purpose of the threshold configuration table is to configure
threshold alarm notifications indicating that a specific performance
metric is not being met.
Each row in the table represents a Loss Measurement session threshold
set for the defined MEP. This table uses five indices. The first three
indices are the indices of the Maintenance Domain, MaNet, and MEP tables.
The fourth index is the specific LM session on the selected MEP. The
fifth index is the specific threshold set number.
Rows in this table are not created automatically. A row is created in
this table to set up a threshold set on a configured MEP that has a
configured LM session.
If two managers try to 'create' the same row at the same time, the first
creation would succeed, the second creation attempt would result in an
error. The second creation attempt would then need to select a new index
value to successfully create a new row.
An NE needs to support at least one threshold set for NE SOAM PM compliance. A
second threshold set on the NE is desirable. More than two threshold
sets can be configured on the NE if supported on the NE.
All the objects in the row have a default value that disables the
particular threshold measurement. In order to enable a threshold
measurement the particular bit in the jnxSoamLmThresholdCfgEnable object
is to be set to '1' and the selected threshold measurement is to have
a threshold value configured. Non-configured threshold measurements
are disabled by default.
The writable objects in this table need to be persistent upon reboot
or restart of a device.
"
::= { jnxSoamPmLmObjects 5 }
jnxSoamLmThresholdCfgEntry OBJECT-TYPE
SYNTAX JnxSoamLmThresholdCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamLmThresholdCfgTable."
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamLmCfgIndex,
jnxSoamLmThresholdCfgIndex
}
::= {jnxSoamLmThresholdCfgTable 1 }
JnxSoamLmThresholdCfgEntry ::= SEQUENCE {
jnxSoamLmThresholdCfgIndex Unsigned32,
jnxSoamLmThresholdCfgEnable BITS,
jnxSoamLmThresholdCfgAvgFlrForwardThreshold Unsigned32,
jnxSoamLmThresholdCfgAvgFlrBackwardThreshold Unsigned32,
jnxSoamLmThresholdCfgRowStatus RowStatus
}
jnxSoamLmThresholdCfgIndex OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index of the threshold number for the specific LM
threshold entry.
An index value of '1' needs to be supported. Other index values
can also be supported.
"
::= { jnxSoamLmThresholdCfgEntry 1 }
jnxSoamLmThresholdCfgEnable OBJECT-TYPE
SYNTAX BITS {
bJnxSoamLmMeasuredFlrForwardThreshold(0),
bJnxSoamLmMaxFlrForwardThreshold(1),
bJnxSoamLmAvgFlrForwardThreshold(2),
bJnxSoamLmMeasuredFlrBackwardThreshold(3),
bJnxSoamLmMaxFlrBackwardThreshold(4),
bJnxSoamLmAvgFlrBackwardThreshold(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A vector of bits that indicates the type of SOAM LM thresholds
notifications that are enabled.
A bit set to '1' enables the specific SOAM LM threshold notification
and when the specific counter is enabled and the threshold is crossed a
notification is generated.
A bit set to '0' disables the specific SOAM LM threshold notification.
If a particular SOAM LM threshold is not supported the BIT value is
set to '0'.
bJnxSoamLmMeasuredFlrForwardThreshold(0)
Enables/disables measured frame loss forward ratio threshold
notification. The notification is sent immediately when the
jnxSoamLmMeasuredStatsForwardFlr value is
greater than or equal to the threshold value.
bJnxSoamLmMaxFlrForwardThreshold(1)
Enables/disables maximum frame loss forward ratio threshold
notification. The notification is sent immediately when the
jnxSoamLmCurrentStatsForwardMaxFlr value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamLmAvgFlrForwardThreshold(2)
Enables/disables average frame loss forward ratio threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamLmCurrentStatsForwardAvgFlr value is greater
than or equal to the threshold value.
bJnxSoamLmMeasuredFlrBackwardThreshold(3)
Enables/disables measured frame loss backward ratio threshold
notification. The notification is sent immediately when the
jnxSoamLmMeasuredStatsBackwardFlr value is
greater than or equal to the threshold value.
bJnxSoamLmMaxFlrBackwardThreshold(4)
Enables/disables maximum frame loss backward ratio threshold
notification. The notification is sent immediately when the
jnxSoamLmCurrentStatsBackwardMaxFlr value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamLmAvgFlrBackwardThreshold(5)
Enables/disables average frame loss backward ratio threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamLmCurrentStatsBackwardAvgFlr value is
greater than or equal to the threshold value.
"
DEFVAL { { } }
::= { jnxSoamLmThresholdCfgEntry 2 }
jnxSoamLmThresholdCfgAvgFlrForwardThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to set the average forward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.
"
DEFVAL { 100000 }
::= { jnxSoamLmThresholdCfgEntry 3 }
jnxSoamLmThresholdCfgAvgFlrBackwardThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to set the average backward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.
"
DEFVAL { 100000 }
::= { jnxSoamLmThresholdCfgEntry 4 }
jnxSoamLmThresholdCfgRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the row.
The writable columns in a row cannot be changed if the row
is active. All columns are to have a valid value before a row
can be activated.
"
::= { jnxSoamLmThresholdCfgEntry 5 }
-- *****************************************************************************
-- Ethernet Loss Measurement Current Availability Statistic Table
-- *****************************************************************************
jnxSoamLmCurrentAvailStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamLmCurrentAvailStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object contains the current results for a SOAM Loss Measurement
session for availability statistics gathered during the interval
indicated by jnxSoamLmCfgAvailabilityMeasurementInterval.
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Loss Measurement session is running.
The objects in this table apply regardless of the value of
jnxSoamLmCfgType unless otherwise specified in the object description.
Except for jnxSoamLmCurrentAvailStatsIndex,
jnxSoamLmCurrentAvailStatsStartTime, jnxSoamLmCurrentAvailStatsElapsedTime
and jnxSoamLmCurrentAvailStatsSuspect, each object in this table applies
only if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable.
The objects in this table may be persistent upon reboot or restart
of a device.
"
REFERENCE
"[MEF SOAM-PM] D9, D18"
::= { jnxSoamPmLmObjects 6 }
jnxSoamLmCurrentAvailStatsEntry OBJECT-TYPE
SYNTAX JnxSoamLmCurrentAvailStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamLmCurrentAvailStatsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamLmCfgIndex
}
::= { jnxSoamLmCurrentAvailStatsTable 1 }
JnxSoamLmCurrentAvailStatsEntry ::= SEQUENCE {
jnxSoamLmCurrentAvailStatsIndex Unsigned32,
jnxSoamLmCurrentAvailStatsStartTime DateAndTime,
jnxSoamLmCurrentAvailStatsElapsedTime TimeInterval,
jnxSoamLmCurrentAvailStatsSuspect TruthValue,
jnxSoamLmCurrentAvailStatsForwardHighLoss Unsigned32,
jnxSoamLmCurrentAvailStatsBackwardHighLoss Unsigned32,
jnxSoamLmCurrentAvailStatsForwardConsecutiveHighLoss Unsigned32,
jnxSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss Unsigned32,
jnxSoamLmCurrentAvailStatsForwardAvailable Gauge32,
jnxSoamLmCurrentAvailStatsBackwardAvailable Gauge32,
jnxSoamLmCurrentAvailStatsForwardUnavailable Gauge32,
jnxSoamLmCurrentAvailStatsBackwardUnavailable Gauge32,
jnxSoamLmCurrentAvailStatsForwardMinFlr Unsigned32,
jnxSoamLmCurrentAvailStatsForwardMaxFlr Unsigned32,
jnxSoamLmCurrentAvailStatsForwardAvgFlr Unsigned32,
jnxSoamLmCurrentAvailStatsBackwardMinFlr Unsigned32,
jnxSoamLmCurrentAvailStatsBackwardMaxFlr Unsigned32,
jnxSoamLmCurrentAvailStatsBackwardAvgFlr Unsigned32
}
jnxSoamLmCurrentAvailStatsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index for the current availability Measurement Interval for this
PM session. This value will become the value for
jnxSoamLmHistoryAvailStatsIndex once the Measurement Interval
is completed. The duration of the Measurement Interval is specified
by jnxSoamLmCfgAvailabilityMeasurementInterval.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.
"
::= { jnxSoamLmCurrentAvailStatsEntry 1 }
jnxSoamLmCurrentAvailStatsStartTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the current Measurement Interval started.
"
REFERENCE
"[MEF SOAM-PM] R87, R112"
::= { jnxSoamLmCurrentAvailStatsEntry 2 }
jnxSoamLmCurrentAvailStatsElapsedTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the current Measurement Interval has been running, in 0.01
seconds.
"
REFERENCE
"[MEF SOAM-PM] R24, R87, R112"
::= { jnxSoamLmCurrentAvailStatsEntry 3 }
jnxSoamLmCurrentAvailStatsSuspect OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the Measurement Interval has been marked as suspect.
The object is set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
"
REFERENCE
"[MEF SOAM-PM] R39, R40, R41"
::= { jnxSoamLmCurrentAvailStatsEntry 4 }
jnxSoamLmCurrentAvailStatsForwardHighLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of high loss intervals (HLI) over
time in the forward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.
"
REFERENCE
"[MEF 10.2.1] 6.9.9; [MEF SOAM-PM] R87"
::= { jnxSoamLmCurrentAvailStatsEntry 5 }
jnxSoamLmCurrentAvailStatsBackwardHighLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of high loss intervals (HLI) over
time in the backwards direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.
"
REFERENCE
"[MEF 10.2.1] 6.9.9; [MEF SOAM-PM] R87"
::= { jnxSoamLmCurrentAvailStatsEntry 6 }
jnxSoamLmCurrentAvailStatsForwardConsecutiveHighLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.
"
REFERENCE
"[MEF 10.2.1] 6.9.9; [MEF SOAM-PM] R87"
::= { jnxSoamLmCurrentAvailStatsEntry 7 }
jnxSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of consecutive high loss intervals
(CHLI) over time in the backward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.
"
REFERENCE
"[MEF 10.2.1] 6.9.9; [MEF SOAM-PM] R87"
::= { jnxSoamLmCurrentAvailStatsEntry 8 }
jnxSoamLmCurrentAvailStatsForwardAvailable OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of availability indicators
evaluated as available in the forward direction by this MEP during
this Measurement Interval.
"
REFERENCE
"[MEF SOAM-PM] R87; [MEF 10.2.1]"
::= { jnxSoamLmCurrentAvailStatsEntry 9 }
jnxSoamLmCurrentAvailStatsBackwardAvailable OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of availability indicators
evaluated as available in the backward direction by this MEP during
this Measurement Interval.
"
REFERENCE
"[MEF SOAM-PM] R87"
::= { jnxSoamLmCurrentAvailStatsEntry 10 }
jnxSoamLmCurrentAvailStatsForwardUnavailable OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of availability indicators
evaluated as unavailable in the forward direction by this MEP during
this Measurement Interval.
"
REFERENCE
"[MEF SOAM-PM] R87"
::= { jnxSoamLmCurrentAvailStatsEntry 11 }
jnxSoamLmCurrentAvailStatsBackwardUnavailable OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of availability indicators
evaluated as unavailable in the backward direction by this MEP
during this Measurement Interval.
"
REFERENCE
"[MEF SOAM-PM] R87"
::= { jnxSoamLmCurrentAvailStatsEntry 12 }
jnxSoamLmCurrentAvailStatsForwardMinFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 2626 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentAvailStatsEntry 13 }
jnxSoamLmCurrentAvailStatsForwardMaxFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentAvailStatsEntry 14 }
jnxSoamLmCurrentAvailStatsForwardAvgFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentAvailStatsEntry 15 }
jnxSoamLmCurrentAvailStatsBackwardMinFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentAvailStatsEntry 16 }
jnxSoamLmCurrentAvailStatsBackwardMaxFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentAvailStatsEntry 17 }
jnxSoamLmCurrentAvailStatsBackwardAvgFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmCurrentAvailStatsEntry 18 }
-- *****************************************************************************
-- Ethernet Loss Measurement Availability History Statistic Table
-- *****************************************************************************
jnxSoamLmHistoryAvailStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamLmHistoryAvailStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the results for availability history Measurement
Intervals in a SOAM Loss Measurement session.
Rows of this table object are created automatically
by the SNMP Agent when the Loss Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the history statistics for a Loss
Measurement session availability Measurement Interval for the defined
MEP. This table uses five indices. The first three indices are the indices
of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific LM session on the selected MEP. The fifth index index the
specific Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval can be deleted (row deletion). If the availability
Measurement Interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
Except for jnxSoamLmHistoryAvailStatsIndex,
jnxSoamLmHistoryAvailStatsEndTime, jnxSoamLmHistoryAvailStatsElapsedTime and
jnxSoamLmHistoryAvailStatsSuspect, each object in this table applies only
if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, R21, D8, R25"
::= { jnxSoamPmLmObjects 7 }
jnxSoamLmHistoryAvailStatsEntry OBJECT-TYPE
SYNTAX JnxSoamLmHistoryAvailStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamLmHistoryAvailStatsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamLmCfgIndex,
jnxSoamLmHistoryAvailStatsIndex
}
::= { jnxSoamLmHistoryAvailStatsTable 1 }
JnxSoamLmHistoryAvailStatsEntry ::= SEQUENCE {
jnxSoamLmHistoryAvailStatsIndex Unsigned32,
jnxSoamLmHistoryAvailStatsEndTime DateAndTime,
jnxSoamLmHistoryAvailStatsElapsedTime TimeInterval,
jnxSoamLmHistoryAvailStatsSuspect TruthValue,
jnxSoamLmHistoryAvailStatsForwardHighLoss Unsigned32,
jnxSoamLmHistoryAvailStatsBackwardHighLoss Unsigned32,
jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLoss Unsigned32,
jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss Unsigned32,
jnxSoamLmHistoryAvailStatsForwardAvailable Gauge32,
jnxSoamLmHistoryAvailStatsBackwardAvailable Gauge32,
jnxSoamLmHistoryAvailStatsForwardUnavailable Gauge32,
jnxSoamLmHistoryAvailStatsBackwardUnavailable Gauge32,
jnxSoamLmHistoryAvailStatsForwardMinFlr Unsigned32,
jnxSoamLmHistoryAvailStatsForwardMaxFlr Unsigned32,
jnxSoamLmHistoryAvailStatsForwardAvgFlr Unsigned32,
jnxSoamLmHistoryAvailStatsBackwardMinFlr Unsigned32,
jnxSoamLmHistoryAvailStatsBackwardMaxFlr Unsigned32,
jnxSoamLmHistoryAvailStatsBackwardAvgFlr Unsigned32
}
jnxSoamLmHistoryAvailStatsIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for the availability Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1. Measurement Intervals
for availability (stored in this table) are based on
jnxSoamLmCfgAvailabilityMeasurementInterval and are indexed independently
of Measurement Intervals for FLR (stored in jnxSoamLmHistoryStatsTable).
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time.
"
::= { jnxSoamLmHistoryAvailStatsEntry 1 }
jnxSoamLmHistoryAvailStatsEndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the Measurement Interval ended.
"
REFERENCE
"[MEF SOAM-PM] R23, R87, R112"
::= { jnxSoamLmHistoryAvailStatsEntry 2 }
jnxSoamLmHistoryAvailStatsElapsedTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of time that the Measurement Interval ran for,
in 0.01 seconds.
"
REFERENCE
"[MEF SOAM-PM] R24, R87, R112"
::= { jnxSoamLmHistoryAvailStatsEntry 3 }
jnxSoamLmHistoryAvailStatsSuspect OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts service
"
REFERENCE
"[MEF SOAM-PM] R39, R40, R41, R42"
::= { jnxSoamLmHistoryAvailStatsEntry 4 }
jnxSoamLmHistoryAvailStatsForwardHighLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of high loss intervals (HLI) over
time in the forward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.
"
REFERENCE
"[MEF 10.2.1] 6.9.9; [MEF SOAM-PM] R87"
::= { jnxSoamLmHistoryAvailStatsEntry 5 }
jnxSoamLmHistoryAvailStatsBackwardHighLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of high loss intervals (HLI) over
time in the backward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.
"
REFERENCE
"[MEF 10.2.1] 6.9.9; [MEF SOAM-PM] R87"
::= { jnxSoamLmHistoryAvailStatsEntry 6 }
jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.
"
REFERENCE
"[MEF 10.2.1] 6.9.9; 3266 [MEF SOAM-PM] R87"
::= { jnxSoamLmHistoryAvailStatsEntry 7 }
jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.
"
REFERENCE
"[MEF 10.2.1] 6.9.9; [MEF SOAM-PM] R87"
::= { jnxSoamLmHistoryAvailStatsEntry 8 }
jnxSoamLmHistoryAvailStatsForwardAvailable OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of availability indicators
evaluated as available in the forward direction by this MEP during
this Measurement Interval.
"
REFERENCE
"[MEF SOAM-PM] R87; [MEF 10.2.1]"
::= { jnxSoamLmHistoryAvailStatsEntry 9 }
jnxSoamLmHistoryAvailStatsBackwardAvailable OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of availability indicators
evaluated as available in the backward direction by this MEP during
this Measurement Interval.
"
REFERENCE
"[MEF SOAM-PM] R87"
::= { jnxSoamLmHistoryAvailStatsEntry 10 }
jnxSoamLmHistoryAvailStatsForwardUnavailable OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of availability indicators
evaluated as unavailable in the forward direction by this MEP during
this Measurement Interval.
"
REFERENCE
"[MEF SOAM-PM] R87"
::= { jnxSoamLmHistoryAvailStatsEntry 11 }
jnxSoamLmHistoryAvailStatsBackwardUnavailable OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of availability indicators
evaluated as unavailable in the backward direction by this MEP
during this Measurement Interval.
"
REFERENCE
"[MEF SOAM-PM] R87"
::= { jnxSoamLmHistoryAvailStatsEntry 12 }
jnxSoamLmHistoryAvailStatsForwardMinFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryAvailStatsEntry 13 }
jnxSoamLmHistoryAvailStatsForwardMaxFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryAvailStatsEntry 14 }
jnxSoamLmHistoryAvailStatsForwardAvgFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryAvailStatsEntry 15 }
jnxSoamLmHistoryAvailStatsBackwardMinFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the minimum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryAvailStatsEntry 16 }
jnxSoamLmHistoryAvailStatsBackwardMaxFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the maximum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryAvailStatsEntry 17 }
jnxSoamLmHistoryAvailStatsBackwardAvgFlr OBJECT-TYPE
SYNTAX Unsigned32 (0..100000)
UNITS "milli-percent"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the average one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 3458 0.001 percent.
"
REFERENCE
"[MEF SOAM-PM] D37"
::= { jnxSoamLmHistoryAvailStatsEntry 18 }
-- *****************************************************************************
-- Performance Measurement Delay Threshold Configuration Table
-- *****************************************************************************
jnxSoamDmThresholdCfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamDmThresholdCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the list of Delay Measurement threshold configuration
values for DM Performance Monitoring.
The main purpose of the threshold configuration table is to configure
threshold alarm notifications indicating that a specific performance
metric is not being met.
Each row in the table represents a Delay Measurement session threshold
set for the defined MEP. This table uses five indices. The first three
indices are the indices of the Maintenance Domain, MaNet, and MEP tables.
The fourth index is the specific DM session on the selected MEP. The
fifth index is the specific threshold set number.
Rows in this table are not created automatically. A row is created in
this table to set up a threshold set on a configured MEP that has a
configured DM session.
An NE needs to support at least one threshold set for NE SOAM PM compliance. A
second threshold set on the NE is desirable. More than two threshold
sets on the NE can be configured if supported on the NE.
All the objects in the row have a default value that disables the
particular threshold measurement. In order to enable a threshold
measurement the particular bit in the jnxSoamDmThresholdCfgEnable object
is to be set to '1' and the selected threshold measurement is to have
a threshold value configured. Non-configured threshold measurements
are disabled by default.
The writable objects in this table need to be persistent upon reboot
or restart of a device.
"
::= { jnxSoamPmDmObjects 5 }
jnxSoamDmThresholdCfgEntry OBJECT-TYPE
SYNTAX JnxSoamDmThresholdCfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamDmThresholdCfgTable."
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamDmCfgIndex,
jnxSoamDmThresholdCfgIndex
}
::= {jnxSoamDmThresholdCfgTable 1 }
JnxSoamDmThresholdCfgEntry ::= SEQUENCE {
jnxSoamDmThresholdCfgIndex Unsigned32,
jnxSoamDmThresholdCfgEnable BITS,
jnxSoamDmThresholdCfgAvgFrameDelayTwoWayThreshold Unsigned32,
jnxSoamDmThresholdCfgAvgIfdvTwoWayThreshold Unsigned32,
jnxSoamDmThresholdCfgRowStatus RowStatus
}
jnxSoamDmThresholdCfgIndex OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The index of the threshold number for the specific DM
threshold entry.
An index value of '1' is to be supported. Other index values
can be supported.
"
::= { jnxSoamDmThresholdCfgEntry 1 }
jnxSoamDmThresholdCfgEnable OBJECT-TYPE
SYNTAX BITS {
bJnxSoamDmMeasuredFrameDelayTwoWayThreshold(0),
bJnxSoamDmMaxFrameDelayTwoWayThreshold(1),
bJnxSoamDmAvgFrameDelayTwoWayThreshold(2),
bJnxSoamDmMeasuredIfdvTwoWayThreshold(3),
bJnxSoamDmMaxIfdvTwoWayThreshold(4),
bJnxSoamDmAvgIfdvTwoWayThreshold(5),
bJnxSoamDmMaxFrameDelayRangeTwoWayThreshold(6),
bJnxSoamDmAvgFrameDelayRangeTwoWayThreshold(7),
bJnxSoamDmMeasuredFrameDelayForwardThreshold(8),
bJnxSoamDmMaxFrameDelayForwardThreshold(9),
bJnxSoamDmAvgFrameDelayForwardThreshold(10),
bJnxSoamDmMeasuredIfdvForwardThreshold(11),
bJnxSoamDmMaxIfdvForwardThreshold(12),
bJnxSoamDmAvgIfdvForwardThreshold(13),
bJnxSoamDmMaxFrameDelayRangeForwardThreshold(14),
bJnxSoamDmAvgFrameDelayRangeForwardThreshold(15),
bJnxSoamDmMeasuredFrameDelayBackwardThreshold(16),
bJnxSoamDmMaxFrameDelayBackwardThreshold(17),
bJnxSoamDmAvgFrameDelayBackwardThreshold(18),
bJnxSoamDmMeasuredIfdvBackwardThreshold(19),
bJnxSoamDmMaxIfdvBackwardThreshold(20),
bJnxSoamDmAvgIfdvBackwardThreshold(21),
bJnxSoamDmMaxFrameDelayRangeBackwardThreshold(22),
bJnxSoamDmAvgFrameDelayRangeBackwardThreshold(23)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A vector of bits that indicates the type of SOAM DM threshold
notifications that are enabled.
A bit set to '1' enables the specific SOAM DM threshold notification
and when the specific counter is enabled and the threshold is crossed a
notification is generated.
A bit set to '0' disables the specific SOAM DM threshold notification.
If a particular SOAM DM threshold is not supported the BIT value is
set to '0'.
bJnxSoamDmMeasuredFrameDelayTwoWayThreshold(0)
Enables/disables measured frame two-way delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayTwoWay value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayTwoWayThreshold(1)
Enables/disables maximum frame two-way delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayTwoWayMax value is
greater than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayTwoWayThreshold(2)
Enables/disables average frame two-way delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvTwoWayThreshold(3)
Enables/disables measured frame IFDV two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvTwoWay value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvTwoWayThreshold(4)
Enables/disables maximum frame IFDV two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvTwoWayMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvTwoWayThreshold(5)
Enables/disables average frame IFDV two-way threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeTwoWayThreshold(6)
Enables/disables maximum Frame Delay Range two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeTwoWayThreshold(7)
Enables/disables average Frame Delay Range two-way threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredFrameDelayForwardThreshold(8)
Enables/disables measured forward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayForward value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayForwardThreshold(9)
Enables/disables maximum forward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayForwardMax value is
greater than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayForwardThreshold(10)
Enables/disables average forward frame delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvForwardThreshold(11)
Enables/disables measured frame IFDV forward threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvForward value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvForwardThreshold(12)
Enables/disables maximum frame IFDV forward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvForwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvForwardThreshold(13)
Enables/disables average frame IFDV forward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeForwardThreshold(14)
Enables/disables maximum Frame Delay Range forward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeForwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeForwardThreshold(15)
Enables/disables average Frame Delay Range forward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredFrameDelayBackwardThreshold(16)
Enables/disables measured backward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayBackward value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayBackwardThreshold(17)
Enables/disables maximum backward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayBackwardMax value is
greater than or equal to threshold value in a
Measurement Interval.
bJnxSoamDmAvgFrameDelayBackwardThreshold(18)
Enables/disables average backward frame delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayBackwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvBackwardThreshold(19)
Enables/disables measured frame IFDV backward threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvBackward value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvBackwardThreshold(20)
Enables/disables maximum frame IFDV backward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvBackwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvBackwardThreshold(21)
Enables/disables average frame IFDV backward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvBackwardAvg value is greater
than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeBackwardThreshold(22)
Enables/disables maximum Frame Delay Range backward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeBackwardThreshold(23)
Enables/disables average Frame Delay Range backward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg value is greater
than or equal to the threshold value.
"
DEFVAL { { } }
::= { jnxSoamDmThresholdCfgEntry 2 }
jnxSoamDmThresholdCfgAvgFrameDelayTwoWayThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to set the average two-way delay threshold
value that will be used to determine if a threshold notification is
generated.
"
DEFVAL { 4294967295 }
::= { jnxSoamDmThresholdCfgEntry 3 }
jnxSoamDmThresholdCfgAvgIfdvTwoWayThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to set the average two-way IFDV threshold
value that will be used to determine if a threshold notification is
generated.
"
DEFVAL { 4294967295 }
::= { jnxSoamDmThresholdCfgEntry 4 }
jnxSoamDmThresholdCfgRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the row.
The writable columns in a row cannot be changed if the row
is active. All columns are to have a valid value before a row
can be activated.
"
::= { jnxSoamDmThresholdCfgEntry 5 }
-- *****************************************************************************
-- Ethernet Delay Measurement Bin Configuration Table
-- *****************************************************************************
jnxSoamDmCfgMeasBinTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamDmCfgMeasBinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table includes configuration objects for the Delay Measurement
bins to collect stats.
Each row in the table is automatically created when the Delay
Measurement session is defined for the selected MEP. The number of rows
created is based upon three items: the DM type, the number of bins
defined for each type, and whether bins are enabled for each type.
The first four indices are the same as used to create the DM session:
Maintenance Domain, MaNet, MEP identification, and jnxSoamDmCfgIndex. The
fifth index is the type of bin, and the sixth index is the bin number.
For a dmDmm session all nine types of bins can be created. For a dm1DmmTx
session no bins are created. For a dm1DmmRx session only types
forwardFrameDelay, forwardIfdv, and forwardFrameDelayRange can be created.
The number of bins created for a bin type is based upon: the
jnxSoamDmCfgNumMeasBinsPerFrameDelayInterval object, the
jnxSoamDmCfgNumMeasBinsPerInterFrameDelayVariationInterval object, the
jnxSoamDmCfgNumMeasBinsPerFrameDelayRangeInterval object, and
the jnxSoamDmCfgMeasurementEnable object.
For instance, if a dmDmm session with Bins per Frame Delay Interval
set to 5, Bins per Frame Delay Variation Interval set to 3, and Frame
Delay Range set to 2 (default), all of the appropriate bits set in
jnxSoamDmMeasurementCfgEnable, the following number of rows would be
created:
For bin types TwoWayFrameDelay(1), forwardFrameDelay(2), and
backwardFrameDelay(3) = 5 bins * 3 types = 15 rows
For bin types TwoWayIfdv(4), forwardIfdv(5), backwardIfdv(6) =
3 bins * 3 types = 9 rows.
For bins types twoWayFrameDelayRange(7), forwardFrameDelayRange(8),
backwardFrameDelayRange(9) =
2 bins * 3 types = 6 rows.
This gives a total of 30 rows created for the DMM session example.
Each value in the bin defaults to 5000us greater than the previous bin,
with the first bin default value set to 0.
For the delay example above (5 bins), the following default values
would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < 10,000us)
bin 3: 10000 (range is 10,000us <= measurement < 15,000us)
bin 4: 15000 (range is 15,000us <= measurement < 20,000us)
bin 5: 20000 (range is 20,000us <= measurement < infinity)
For the delay variation example above (3 bins), the following default
values would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < 10,000us)
bin 3: 10000 (range is 10,000us <= measurement < infinity)
For the frame delay range example above (2 bins), the following default
values would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < infinity)
The writable objects in this table need to be persistent upon reboot
or restart of a device.
Rows are only created if the corresponding measurement type has been enabled
via the jnxSoamDmCfgMeasurementEnable object.
"
REFERENCE
"[MEF SOAM-PM] R34, R36, R37, D17, R38, R65, D26, D27, R99, D43, D44"
::= { jnxSoamPmDmObjects 6 }
jnxSoamDmCfgMeasBinEntry OBJECT-TYPE
SYNTAX JnxSoamDmCfgMeasBinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamDmCfgMeasBinTable."
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamDmCfgIndex,
jnxSoamDmCfgMeasBinType,
jnxSoamDmCfgMeasBinNumber
}
::= { jnxSoamDmCfgMeasBinTable 1 }
JnxSoamDmCfgMeasBinEntry ::= SEQUENCE {
jnxSoamDmCfgMeasBinType JnxSoamTcDelayMeasurementBinType,
jnxSoamDmCfgMeasBinNumber Unsigned32,
jnxSoamDmCfgMeasBinLowerBound Unsigned32
}
jnxSoamDmCfgMeasBinType OBJECT-TYPE
SYNTAX JnxSoamTcDelayMeasurementBinType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies whether the bin number is for
Frame Delay or Inter-Frame Delay Variation.
"
::= { jnxSoamDmCfgMeasBinEntry 1 }
jnxSoamDmCfgMeasBinNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object specifies the bin number for the
configured boundary. The first bin has bin number 1.
"
::= { jnxSoamDmCfgMeasBinEntry 2 }
jnxSoamDmCfgMeasBinLowerBound OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds (us)"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the lower boundary for a
measurement bin. The upper boundary is defined by the next bin
value or infinite for the last bin defined.
The measurement boundary for each measurement bin is to
be larger than the measurement boundary of the preceding
measurement bin. By default, the next bin is set to 5000us larger
than the lower bin boundary.
The values in a bin boundary object represents the time range
used to segregate delay data into the appropriate statistical
data bin. For five bins with default values, each bin has the
following time range:
bin 1 = 0, range is 0us <= measurement < 5,000us
bin 2 = 5000, range is 5,000us <= measurement < 10,000us
bin 3 = 10000, range is 10,000us <= measurement < 15,000us
bin 4 = 15000, range is 15,000us <= measurement < 20,000us
< infinity
The first bin boundary (jnxSoamDmCfgBinNumber set to 1) always contains
the value of 0. Attempting to write a non-zero value to this bin will
result in an error.
"
REFERENCE
"[MEF SOAM-PM] R33, R35, D17"
::= { jnxSoamDmCfgMeasBinEntry 3 }
-- *****************************************************************************
-- Ethernet Delay Measurement Current Bin Statistic Table
-- *****************************************************************************
jnxSoamDmCurrentStatsBinsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamDmCurrentStatsBinsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the result bins for the current Measurement
Interval in a SOAM Delay Measurement session.
Each row in the table represents the current bin statistics for a
Delay Measurement session for the defined MEP. This table uses six
indices. The first three indices are the indices of the Maintenance
Domain, MaNet, and MEP tables. The fourth index is the specific DM
session on the selected MEP. The fifth index indicates bin type and
the sixth indicates the specific bin number.
A row in this table is created automatically by the SNMP Agent when
the Delay Measurement session is configured and the bin counter value
is set to 0.
The objects in this table are ignored if jnxSoamDmCfgType is 1DmTx.
This table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot
or restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, D9"
::= { jnxSoamPmDmObjects 7 }
jnxSoamDmCurrentStatsBinsEntry OBJECT-TYPE
SYNTAX JnxSoamDmCurrentStatsBinsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamDmCurrentStatsBinsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamDmCfgIndex,
jnxSoamDmCfgMeasBinType,
jnxSoamDmCfgMeasBinNumber
}
::= { jnxSoamDmCurrentStatsBinsTable 1 }
JnxSoamDmCurrentStatsBinsEntry ::= SEQUENCE {
jnxSoamDmCurrentStatsBinsCounter Gauge32
}
jnxSoamDmCurrentStatsBinsCounter OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of completed
measurements initiated in this Measurement Interval whose value
falls within the range specified for this bin (that is, greater
than or equal to the measurement boundary for the bin, and
(unless the bin is the last bin) less than the measurement
boundary for the following bin.
"
REFERENCE
"[MEF SOAM-PM] R66, R67, R100, R101"
::= { jnxSoamDmCurrentStatsBinsEntry 1 }
-- *****************************************************************************
-- Ethernet Delay Measurement Bin History Statistic Table
-- *****************************************************************************
jnxSoamDmHistoryStatsBinsTable OBJECT-TYPE
SYNTAX SEQUENCE OF JnxSoamDmHistoryStatsBinsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the result bins for the history Measurement
Intervals in a SOAM Delay Measurement session.
Rows of this table are created automatically
by the SNMP Agent when the Delay Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the Measurement Interval history
statistics for a specific bin in a Delay Measurement session for the
defined MEP. This table uses seven indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP. The
fifth index is the Measurement Interval. The sixth index is the
specific bin type. The seventh index is the specific bin number.
Rows in this table pertaining to a given Measurement Interval are
row in the
jnxSoamDmHistoryStatsTable is deleted.
The objects in this table are ignored if jnxSoamDmCfgType is 1DmTx.
This table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table need to be persistent upon reboot
or restart of a device.
"
REFERENCE
"[MEF SOAM-PM] R7, R15, R21, D8, R66, R67"
::= { jnxSoamPmDmObjects 8 }
jnxSoamDmHistoryStatsBinsEntry OBJECT-TYPE
SYNTAX JnxSoamDmHistoryStatsBinsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The conceptual row of jnxSoamDmHistoryStatsBinsTable"
INDEX {
dot1agCfmMdIndex,
dot1agCfmMaIndex,
dot1agCfmMepIdentifier,
jnxSoamDmCfgIndex,
jnxSoamDmHistoryStatsIndex,
jnxSoamDmCfgMeasBinType,
jnxSoamDmCfgMeasBinNumber
}
::= { jnxSoamDmHistoryStatsBinsTable 1 }
JnxSoamDmHistoryStatsBinsEntry ::= SEQUENCE {
jnxSoamDmHistoryStatsBinsCounter Gauge32
}
jnxSoamDmHistoryStatsBinsCounter OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the count of the number of completed
measurements initiated in this Measurement Interval whose value
falls within the range specified for this bin (that is, greater
than or equal to the measurement boundary for the bin, and
(unless the bin is the last bin) less than the measurement
boundary for the following bin.
"
REFERENCE
"[MEF SOAM-PM] R66, R67, R100, R101"
::= { jnxSoamDmHistoryStatsBinsEntry 1 }
-- *****************************************************************************
-- Notification Data Objects
-- *****************************************************************************
jnxSoamPmNotificationObjDateAndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object contains the time and date at the time that
the notification event is detected, not the time of the notification
generation.
This object is used only for notifications. The mechanism to set and keep
current the date and time is not specified.
"
::= { jnxSoamPmNotificationObj 1 }
jnxSoamPmNotificationObjThresholdId OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The Object Identifier of the object that caused the generation of the
notification from the jnxSoamLmThresholdEntry or jnxSoamDmThresholdEntry.
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 2 }
jnxSoamPmNotificationObjThresholdConfig OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The configured threshold value of the object that caused the generation
of the notification.
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 3 }
jnxSoamPmNotificationObjThresholdValue OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The measured value of the object at the time of the generation of the
Notification, from the jnxSoamLmMeasuredStatsTable,
jnxSoamLmCurrentStatsTable,
jnxSoamDmMeasuredStatsTable or jnxSoamDmCurrentStatsTable.
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 4 }
jnxSoamPmNotificationObjSuspect OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The suspect flag for the current Measurement Interval in which the
notification was generated from the jnxSoamLmCurrentStatsTable,
or jnxSoamDmCurrentStatsTable.
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 5 }
jnxSoamPmNotificationObjCrossingType OBJECT-TYPE
SYNTAX INTEGER {
aboveAlarm (1),
setAlarm (2),
clearAlarm (3)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The Notification Crossing Type of the object that caused the generation
of the notification from the jnxSoamLmThresholdEntry or
jnxSoamDmThresholdEntry.
aboveAlarm(1) indicates that the crossing type alarm was an above
threshold
setAlarm(2) indicates that the crossing type alarm was a set
threshold
clearAlarm(3) indicates that the crossing type alarm was a clear
threshold
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 6 }
jnxSoamPmNotificationObjDestinationMep OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The MAC address of the Destination MEP associated the notification found
in either the jnxSoamDmCfgTable or jnxSoamLmCfgTable.
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 7 }
jnxSoamPmNotificationObjPriority OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The CoS priority of the associated notification found
in either the jnxSoamDmCfgTable or jnxSoamLmCfgTable.
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 8 }
jnxSoamPmNotificationTotalFlaps OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The measured value of total number of flaps occured during the
flap trap timer itnerval.
"
::= { jnxSoamPmNotificationObj 9 }
jnxSoamPmNotificationAccTotalFlaps OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The measured value of total number of accumulated flaps occured during the
flap trap timer itnerval.
"
::= { jnxSoamPmNotificationObj 10 }
jnxSoamPmNotificationObjThresholdLastValue OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The measured value of the object at the time of the generation of the
last Notification during the flap trap timer interval.
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 11 }
jnxSoamPmNotificationObjCurrentState OBJECT-TYPE
SYNTAX INTEGER {
aboveAlarm (1),
setAlarm (2),
clearAlarm (3)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The Current Notification Crossing Type of the
object that caused the generation
of the notification at the end of timer interval
from the jnxSoamLmThresholdEntry or
jnxSoamDmThresholdEntry.
aboveAlarm(1) indicates that the crossing type alarm was an above
threshold
setAlarm(2) indicates that the crossing type alarm was a set
threshold
clearAlarm(3) indicates that the crossing type alarm was a clear
threshold
This object is only used for the notification.
"
::= { jnxSoamPmNotificationObj 12 }
jnxSoamPmNotificationObjLastDateAndTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object contains the time and date at the time that
the last notification event is detected, at the end of flap timer interval
and not the time of the first notification
generation.
This object is used only for notifications. The mechanism to set and keep
current the date and time is not specified.
"
::= { jnxSoamPmNotificationObj 13 }
-- *****************************************************************************
-- NOTIFICATIONS (TRAPS)
-- *****************************************************************************
jnxSoamLmSessionStartStopAlarm NOTIFICATION-TYPE
OBJECTS {
jnxSoamLmCfgSessionStatus,
jnxSoamPmNotificationObjDateAndTime,
jnxSoamPmNotificationObjDestinationMep
}
STATUS current
DESCRIPTION
"An jnxSoamLmSessionStartStopAlarm notification is sent when the state of
jnxSoamLmCfgSessionStatus changes.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the individual PM session reporting the start/stop
by the indices in the OID jnxSoamLmCfgSessionStatus, including
dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier, and
jnxSoamLmCfgIndex.
An agent is not to generate more than one jnxSoamLmSessionStartStopAlarm
'notification-event' in a given time interval per LM session as specified
by the jnxSoamPmNotificationCfgAlarmInterval. A 'notification-event' is
the transmission of a single notification to a list of notification
destinations.
If additional operational state changes occur within the
jnxSoamPmNotificationCfgAlarmInterval period, then notification
generation for these changes are be suppressed by the agent until
the current alarm interval expires. At the end of an alarm interval
period, one notification-event is generated if any operational
state changes occurred since the start of the alarm interval period. In
such a case, another alarm interval period is started right away.
"
::= { jnxSoamPmNotifications 1 }
jnxSoamDmSessionStartStopAlarm NOTIFICATION-TYPE
OBJECTS {
jnxSoamDmCfgSessionStatus,
jnxSoamPmNotificationObjDateAndTime,
jnxSoamPmNotificationObjDestinationMep
}
STATUS current
DESCRIPTION
"An jnxSoamDmSessionStartStopAlarm notification is sent when the state of
jnxSoamDmCfgSessionStatus changes.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the individual PM session reporting the start/stop
by the indices in the OID jnxSoamDmCfgSessionStatus, including
dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier, and
jnxSoamDmCfgIndex.
An agent is not to generate more than one jnxSoamDmSessionStartStopAlarm
'notification-event' in a given time interval per DM session as specified
by jnxSoamPmNotificationCfgAlarmInterval. A 'notification-event' is the
transmission of a single notification to a list of notification
destinations.
If additional operational state changes occur within the
jnxSoamPmNotificationCfgAlarmInterval period, then notification generation
for these changes are suppressed by the agent until the current alarm
interval expires. At the end of an alarm interval period, one
notification-event is generated if any operational state changes
occurred since the start of the alarm interval period. In such a case,
another alarm interval period is started right away.
"
::= { jnxSoamPmNotifications 2 }
jnxSoamPmThresholdCrossingAlarm NOTIFICATION-TYPE
OBJECTS {
jnxSoamPmNotificationObjCrossingType,
jnxSoamPmNotificationObjThresholdId,
jnxSoamPmNotificationObjThresholdConfig,
jnxSoamPmNotificationObjThresholdValue,
jnxSoamPmNotificationObjSuspect,
jnxSoamPmNotificationObjDateAndTime,
jnxSoamPmNotificationObjDestinationMep
}
STATUS current
DESCRIPTION
"An jnxSoamPmThresholdCrossingAlarm notification is sent if the
following conditions are met for a particular type.
For an aboveAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdAboveAlarm is enabled;
and
d) the measured value of the parameter exceeds the value configured in
the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdAboveAlarm; and
e) no previous jnxSoamPmThresholdCrossingAlarm notifications with type
aboveAlarm have been sent relating to the same threshold in the
jnxSoamLmThresholdCfgTable or jnxSoamDmThresholdCfgTable and the
same parameter, during this Measurement Interval.
For a setAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdSetClearAlarm is enabled;
and
d) the measured value of the parameter exceeds the value configured in
the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdSetClearAlarm for the Measurement Interval; and
e) the previous measured value did not
exceed the value configured in the jnxSoamLmThresholdCfgTable for
a LM crossing entry or jnxSoamDmThresholdCfgTable for a DM crossing
entry for a type of bPmThresholdSetClearAlarm.
For a clearAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdSetClearAlarm is enabled;
and
d) the measured value of the parameter did not exceed the value configured
in the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdSetClearAlarm for the Measurement Interval; and
e) the previous measured value did
exceed the value configured in the jnxSoamLmThresholdCfgTable for
a LM crossing entry or jnxSoamDmThresholdCfgTable for a DM crossing
entry for a type of bPmThresholdSetClearAlarm.
In the case of thresholds applied to a maximum or average measurement
counter, the previous measured value is the value of the counter at the
end of the preceding Measurement Interval. In the case of thresholds
applied to the last measured value, it is the previous measured value.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the LM or DM session reporting the threshold
crossing by the indices in the jnxSoamPmNotificationCfgThresholdId object,
including dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier,
and the jnxSoamLmCfgIndex or jnxSoamDmCfgIndex.
An agent is not to generate more than one jnxSoamLmThresholdCrossingAlarm
'notification-event' of a given type per LM or DM session as specified
by jnxSoamPmNotificationCfgAlarmInterval. A 'notification-event' is the
transmission of a single notification to a list of notification
destinations.
If additional threshold crossing events occur within the
jnxSoamPmNotificationCfgAlarmInterval period, then notification
generation for these changes are suppressed by the agent until
the current alarm interval expires. At the end of an alarm interval
period, one notification-event is generated if any threshold
crossing events occurred since the start of the alarm interval period.
In such a case, another alarm interval period is started right away.
"
::= { jnxSoamPmNotifications 3 }
jnxSoamPmThresholdFlapAlarm NOTIFICATION-TYPE
OBJECTS {
jnxSoamPmNotificationObjThresholdId,
jnxSoamPmNotificationObjThresholdConfig,
jnxSoamPmNotificationObjThresholdLastValue,
jnxSoamPmNotificationTotalFlaps,
jnxSoamPmNotificationAccTotalFlaps,
jnxSoamPmNotificationObjCurrentState,
jnxSoamPmNotificationObjDestinationMep
}
STATUS current
DESCRIPTION
" The jnxSoamPmThresholdFlapAlarm is sent when the CFM Threshold Flap
Notification feature is enabled which would dampen the
jnxSoamPmThresholdCrossingAlarm sent to NMS. The jnxSoamPmThresholdFlapAlarm
gives details about Flaps occured during the time interval. The
jnxSoamPmThresholdFlapAlarm is sent for the follwing below conditions
a) Trap is sent if one flap sequence has occured
b) Trap is sent if threshold or timer changes happens.
c) Trap is sent when finite iterations counts expires.
"
::= { jnxSoamPmNotifications 4 }
END