mibs/nokia/aos7/ALCATEL-IND1-PIM-MIB
ALCATEL-IND1-PIM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
NOTIFICATION-TYPE,
IpAddress, Integer32, TimeTicks,
Unsigned32, Counter32
FROM SNMPv2-SMI
InetAddressType, InetAddress,
InetAddressPrefixLength
FROM INET-ADDRESS-MIB
pimInterfaceEntry
FROM PIM-STD-MIB
RowStatus, TruthValue
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
routingIND1Pim
FROM ALCATEL-IND1-BASE;
alcatelIND1PIMMIB MODULE-IDENTITY
LAST-UPDATED "201505280000Z"
ORGANIZATION "Alcatel-Lucent"
CONTACT-INFO
"Please consult with Customer Service to ensure the most appropriate
version of this document is used with the products in question:
Alcatel-Lucent, Enterprise Solutions Division
(Formerly Alcatel Internetworking, Incorporated)
26801 West Agoura Road
Agoura Hills, CA 91301-5122
United States Of America
Telephone: North America +1 800 995 2696
Latin America +1 877 919 9526
Europe +31 23 556 0100
Asia +65 394 7933
All Other +1 818 878 4507
Electronic Mail: support@ind.alcatel.com
World Wide Web: http://alcatel-lucent.com/wps/portal/enterprise
File Transfer Protocol: ftp://ftp.ind.alcatel.com/pub/products/mibs"
DESCRIPTION
"This module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
This proprietary MIB contains management information for
the configuration of PIM-SM and PIM-DM global configuration
parameters.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2007 Alcatel-Lucent
Copyright (C) 2015 ALE USA, Inc.
ALL RIGHTS RESERVED WORLDWIDE"
REVISION "200704030000Z"
DESCRIPTION
"The latest version of this MIB Module."
REVISION "201505280000Z"
DESCRIPTION
"Added V4/V6 bidir ssm compatibility, bidir fast-join, asm fast-join and ssm-fast-join."
::= { routingIND1Pim 1 }
alcatelIND1PIMMIBObjects OBJECT IDENTIFIER ::= { alcatelIND1PIMMIB 1 }
alaPimsmGlobalConfig OBJECT IDENTIFIER ::= { alcatelIND1PIMMIBObjects 1 }
alaPimdmGlobalConfig OBJECT IDENTIFIER ::= { alcatelIND1PIMMIBObjects 2 }
alaPimGlobalConfig OBJECT IDENTIFIER ::= { alcatelIND1PIMMIBObjects 3 }
-- ************************************************************************
-- PIM-SM Global Configuration
-- ************************************************************************
alaPimsmAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables the
PIM-SM protocol on this router."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 1}
alaPimsmMaxRPs OBJECT-TYPE
SYNTAX Integer32 (1..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of C-RPs allowed in the PIM-SM
domain."
DEFVAL { 32 }
::= { alaPimsmGlobalConfig 2 }
alaPimsmProbeTime OBJECT-TYPE
SYNTAX Integer32 (1..300)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When NULL Registers are used, this is the time
between sending a NULL Register and the Register-
Suppression-Timer expiring unless it is restarted
by receiving a Register-Stop."
DEFVAL { 5 }
::= { alaPimsmGlobalConfig 3}
alaPimsmOldRegisterMessageSupport OBJECT-TYPE
SYNTAX INTEGER {
header(1),
full(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the application of the checksum function on
received Register messages in the PIM-SM domain. When
set to full(2), the checksum for a register message
is computed for the entire packet (i.e. includes data).
When set to header(1), the checksum is done only on the
first 8 bytes of the packet. This variable is provided
for interoperability reasons and may be required for
Compatibility with older implementations of PIM-SM v2.
This parameter must be set the same throughout the
PIM-SM domain."
DEFVAL { header }
::= { alaPimsmGlobalConfig 4 }
alaPimsmAdminSPTConfig OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables SPT Switchover
upon receiving the first data packet."
DEFVAL { enable }
::= {alaPimsmGlobalConfig 5 }
alaPimsmRPThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Sets the RP threshold value (in bps) to be used
in determining when to switch to native
forwarding at the RP. The value of 0
disables the RP Threshold functionality."
DEFVAL { 1 }
::= {alaPimsmGlobalConfig 6 }
alaPimsmV6AdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables the
PIM-SM IPv6 protocol on this router."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 7 }
alaPimsmV6SPTConfig OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables PIM IPv6 SPT Switchover
upon receiving the first data packet."
DEFVAL { enable }
::= {alaPimsmGlobalConfig 8 }
alaPimsmV6RPSwitchover OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether PIM IPv6
will attempt to switch to native forwarding at the RP
upon receiving the first register-encapsulated packet."
DEFVAL { enable }
::= {alaPimsmGlobalConfig 9 }
alaPimsmBidirStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables the
PIM BIDIR protocol on this router."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 10}
alaPimsmBidirPeriodicInterval OBJECT-TYPE
SYNTAX Integer32 (0..2000)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This is the interval at which the DF for each RPA
will periodically announce its status in a
Winner message.
A value of 0 indicates that periodic messages will
not be sent."
DEFVAL { 60 }
::= { alaPimsmGlobalConfig 11 }
alaPimsmBidirDFAbort OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether the DF
election will be automatically aborted if a PIM hello
is received from a PIM neighbor without the
bidirectional capable option. By default, the DF
election will still occur among those PIM routers that
support BIDIR. By enabling this option, if a BIDIR-
capable router receives a PIM hello from a
non-BIDIR-capable router, the DF election is aborted."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 12}
alaPimsmNonBidirHelloPeriod OBJECT-TYPE
SYNTAX Unsigned32 (10..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum time that must elapse between
alaPimNonBidirHello notifications originated by this router.
The default value of 65535 represents an 'infinite' time, in
which case, no alaPimNonBidirHello notifications are ever
sent.
The non-zero minimum allowed value provides resilience
against propagation of denial-of-service attacks from the
control plane to the network management plane."
DEFVAL { 65535 }
::= { alaPimsmGlobalConfig 13 }
alaPimsmNonBidirHelloMsgsRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PIM Hello messages that have been
received by a BIDIR-capable device that do not have the
Bidirectional Capable option.
This counter is incremented if BIDIR mode is enabled on
this router and a PIM Hello message is received from a
PIM neighbor that does not include the Bidirectional Capable
option.
By default, the reception of these messages will not
effect the BIDIR DF election. The alaPimsmBidirDFAbort
object may be used to change the default behavior
and have the DF election aborted whenever a BIDIR-capable
router receives a PIM hello from a non-BIDIR-capable
router."
::= { alaPimsmGlobalConfig 14 }
alaPimsmNonBidirHelloAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type stored in alaPimsmNonBidirHelloOrigin.
If no Non Bidir Hello messages have been received, this
object is set to unknown(0)."
::= { alaPimsmGlobalConfig 15 }
alaPimsmNonBidirHelloOrigin OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The source address of the last Non Bidir Hello message
received by this device."
::= { alaPimsmGlobalConfig 16 }
alaPimsmV6BidirStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables the
PIM IPv6 BIDIR protocol on this router."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 17}
alaPimsmRPHashStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables applying the PIM hash function
defined in RFC 4601 when selecting an RP from two or more equal
group-range-to-RP mappings."
REFERENCE "RFC 4601 section 4.7.2"
DEFVAL { disable }
::= {alaPimsmGlobalConfig 18 }
alaPimsmBidirSsmCompat OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether PIM
BIDIR will support receiving IGMPv3 source-specific
joins and treat them as a (*,G) join.
By default, IGMPv3 source-specific joins are ignored
when PIM is operating in BIDIR mode."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 19}
alaPimsmV6BidirSsmCompat OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether IPv6 PIM
BIDIR will support receiving MLDv2 source-specific
joins and treat them as a (*,G) join.
By default, MLDv2 source-specific joins are ignored
when PIM is operating in BIDIR mode."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 20}
alaPimsmBidirFastJoin OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether PIM
BIDIR will automatically create the routes in hardware
as soon as the BIDIR (*,G) routes are learned.
By default, this is disabled and the routes are not
installed in hardware until the multicast traffic
reaches the switch."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 21}
alaPimsmV6BidirFastJoin OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether IPv6 PIM
BIDIR will automatically create the routes in hardware
as soon as the BIDIR (*,G) routes are learned.
By default, this is disabled and the routes are not
installed in hardware until the multicast traffic
reaches the switch."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 22}
alaPimsmAsmFastJoin OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether PIM
ASM will automatically create the (*,G) routes in
hardware as soon as the ASM (*,G) routes are learned.
By default, this is disabled and the routes are not
installed in hardware until the multicast traffic
reaches the switch."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 23}
alaPimsmV6AsmFastJoin OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether IPv6 PIM
ASM will automatically create the (*,G) routes in
hardware as soon as the ASM (*,G) routes are learned.
By default, this is disabled and the routes are not
installed in hardware until the multicast traffic
reaches the switch."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 24}
alaPimsmSsmFastJoin OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether PIM
will automatically create the (S,G) routes in
hardware as soon as the (S,G) routes are learned.
This includes PIM Sparse Mode (S,G) routes as well
as PIM SSM (S,G) routes.
By default, this is disabled and the routes are not
installed in hardware until the multicast traffic
reaches the switch."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 25}
alaPimsmV6SsmFastJoin OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables whether IPv6 PIM
will automatically create the (S,G) routes in hardware
as soon as the (S,G) routes are learned.
This includes PIM Sparse Mode (S,G) routes as well
as PIM SSM (S,G) routes.
By default, this is disabled and the routes are not
installed in hardware until the multicast traffic
reaches the switch."
DEFVAL { disable }
::= {alaPimsmGlobalConfig 26}
-- ************************************************************************
-- PIM-DM Global Configuration
-- ************************************************************************
alaPimdmAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables the
PIM-DM protocol on this router."
DEFVAL { disable }
::= {alaPimdmGlobalConfig 1}
alaPimdmStateRefreshTimeToLive OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The TTL to be used by this router's originated State
Refresh messages if the data packet's TTL is not
recorded."
DEFVAL { 16 }
::= {alaPimdmGlobalConfig 2}
alaPimdmStateRefreshLimitInterval OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This router will not forward successive State Refresh
messages received at less than this interval."
DEFVAL { 0 }
::= {alaPimdmGlobalConfig 3}
alaPimdmV6AdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables the
PIM-DM IPv6 protocol on this router."
DEFVAL { disable }
::= {alaPimdmGlobalConfig 4}
--
-- The PIM Dense Group Table
-- This table allows the configuration of pim group mappings to be
-- used with dense mode. These mappings correspond to the sparse
-- mappings defined in the pimStaticRPTable defined in the PIM-STD-MIB.
--
alaPimdmDenseGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlaPimdmDenseGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to manage configuration of dense groups.
If the group prefixes configured for two or more rows in
this table overlap, the row with the greatest value of
alaPimdmDenseGroupGrpPrefixLength is used for the overlapping
range."
::= { alaPimdmGlobalConfig 5 }
alaPimdmDenseGroupEntry OBJECT-TYPE
SYNTAX AlaPimdmDenseGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the alaPimdmDenseGroupTable. This
entry is preserved on agent restart."
INDEX { alaPimdmDenseGroupAddressType,
alaPimdmDenseGroupGrpAddress,
alaPimdmDenseGroupGrpPrefixLength }
::= { alaPimdmDenseGroupTable 1 }
AlaPimdmDenseGroupEntry ::= SEQUENCE {
alaPimdmDenseGroupAddressType InetAddressType,
alaPimdmDenseGroupGrpAddress InetAddress,
alaPimdmDenseGroupGrpPrefixLength InetAddressPrefixLength,
alaPimdmDenseGroupOverrideDynamic TruthValue,
alaPimdmDenseGroupPrecedence Unsigned32,
alaPimdmDenseGroupRowStatus RowStatus
}
alaPimdmDenseGroupAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of this entry."
::= { alaPimdmDenseGroupEntry 1 }
alaPimdmDenseGroupGrpAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group address that, when combined with
alaPimdmDenseGroupGrpPrefixLength, gives the group prefix for this
entry. The InetAddressType is given by the
alaPimdmDenseGroupAddressType object.
This address object is only significant up to
alaPimdmDenseGroupGrpPrefixLength bits. The remainder of the
address bits are zero. This is especially important for
this index field, which is part of the index of this entry.
Any non-zero bits would signify an entirely different
entry."
::= { alaPimdmDenseGroupEntry 2 }
alaPimdmDenseGroupGrpPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength (4..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group prefix length that, when combined
with alaPimdmDenseGroupGrpAddress, gives the group prefix for this
entry. The InetAddressType is given by the
alaPimdmDenseGroupAddressType object. If alaPimdmDenseGroupAddressType is
'ipv4' or 'ipv4z', this object must be in the range 4..32.
If alaPimdmDenseGroupGrpAddressType is 'ipv6' or 'ipv6z', this
object must be in the range 8..128."
::= { alaPimdmDenseGroupEntry 3 }
alaPimdmDenseGroupOverrideDynamic OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Whether this dense group configuration will override other
group mappings in this group prefix. If this object is
TRUE, then it will override:
- RP information learned dynamically for groups in this
group prefix.
- RP information configured in alaPimdmDenseGroupTable with
alaPimdmDenseGroupOverrideDynamic set to FALSE.
See pimGroupMappingTable for details."
DEFVAL { false }
::= { alaPimdmDenseGroupEntry 4 }
alaPimdmDenseGroupPrecedence OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value for pimGroupMappingPrecedence to be used for this
static RP configuration. This allows fine control over
which configuration is overridden by this static
configuration.
If alaPimdmDenseGroupOverrideDynamic is set to TRUE, all dynamic RP
configuration is overridden by this static configuration,
whatever the value of this object.
The absolute values of this object have a significance only
on the local router and do not need to be coordinated with
other routers. A setting of this object may have different
effects when applied to other routers.
Do not use this object unless fine control of static RP
behavior on the local router is required."
::= { alaPimdmDenseGroupEntry 5 }
alaPimdmDenseGroupRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row, by which rows in this table can
be created and destroyed.
All writeable objects in this entry can be modified when the
status of this entry is active(1)."
::= { alaPimdmDenseGroupEntry 6 }
-- ************************************************************************
-- PIM Global Configuration
-- ************************************************************************
alaPimBfdStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables PIM
with the BFD protocol on this router."
DEFVAL { disable }
::= {alaPimGlobalConfig 1}
alaPimBfdAllInterfaceStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables BFD
for all PIM interfaces on this router."
DEFVAL { disable }
::= {alaPimGlobalConfig 2}
alaPimMoFRRStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables MoFRR
(Multicast only Fast Re-Route) on this router."
DEFVAL { disable }
::= {alaPimGlobalConfig 3}
alaPimMoFRRAllRouteStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"By default, MoFRR is only applied to multicast
routes that have local clients. Enabling
alaPimMoFRRAllRouteStatus will enable MoFRR
on all routes whether there are local clients
or not. alaPimMoFRRStatus must be enabled for
this to take effect."
DEFVAL { disable }
::= {alaPimGlobalConfig 4}
-- ************************************************************************
-- Expansion of pimInterfaceEntry
-- ************************************************************************
alaPimInterfaceAugTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlaPimInterfaceAugEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Expansion for pimInterfaceTable"
::= { alaPimGlobalConfig 5 }
alaPimInterfaceAugEntry OBJECT-TYPE
SYNTAX AlaPimInterfaceAugEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry of alaPimInterfaceAugTable"
AUGMENTS { pimInterfaceEntry }
::= { alaPimInterfaceAugTable 1 }
AlaPimInterfaceAugEntry ::= SEQUENCE {
alaPimInterfaceBfdStatus INTEGER
}
alaPimInterfaceBfdStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enables/Disables BFD for particular interfaces of PIM."
DEFVAL { disable }
::= { alaPimInterfaceAugEntry 1 }
alaPimMbrAllSourcesStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables PIM to notify DVMRP about
the routes to all multicast sources learned instead of just
the directly connected subnets so that these routes can be
advertised in the DVMRP domain via standard DVMRP mechanisms.
This object is only applicable if the router is operating as
a Multicast Border Router."
DEFVAL { disable }
::= {alaPimGlobalConfig 6}
alaPimMbrOperStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether MBR is currently enabled/disabled for PIM."
::= {alaPimGlobalConfig 7}
alaPimV6BfdStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables PIM IPv6
with the BFD protocol on this router."
DEFVAL { disable }
::= {alaPimGlobalConfig 8}
alaPimV6BfdAllInterfaceStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Administratively enables/disables BFD
for all PIM IPv6 interfaces on this router."
DEFVAL { disable }
::= {alaPimGlobalConfig 9}
-- ************************************************************************
-- PIM Notifications
-- ************************************************************************
alaPimNotifications OBJECT IDENTIFIER ::= { alcatelIND1PIMMIB 0 }
alaPimNonBidirHello NOTIFICATION-TYPE
OBJECTS { alaPimsmNonBidirHelloAddressType,
alaPimsmNonBidirHelloOrigin }
STATUS current
DESCRIPTION
"An alaPimNonBidirHello notification signifies that
a bidir-capable router has received a PIM hello from
a non-bidir-capable router.
This notification is generated whenever the counter
alaPimsmNonBidirHelloMsgsRcvd is incremented, subject
to the rate limit specified by
alaPimsmNonBidirHelloNotificationPeriod."
::= { alaPimNotifications 1 }
-- conformance information
alcatelIND1PIMMIBConformance OBJECT IDENTIFIER ::= { alcatelIND1PIMMIB 2 }
alcatelIND1PIMMIBCompliances OBJECT IDENTIFIER ::=
{ alcatelIND1PIMMIBConformance 1 }
alcatelIND1PIMMIBGroups OBJECT IDENTIFIER ::=
{ alcatelIND1PIMMIBConformance 2 }
-- compliance statements
alaPimsmCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers running PIM Sparse
Mode and implementing the ALCATEL-IND1-PIM MIB."
MODULE -- this module
MANDATORY-GROUPS { alaPimsmConfigMIBGroup, alaPimConfigMIBGroup }
::= { alcatelIND1PIMMIBCompliances 1 }
alaPimdmCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers running PIM Dense
Mode and implementing the ALCATEL-IND1-PIM MIB."
MODULE -- this module
MANDATORY-GROUPS { alaPimdmConfigMIBGroup, alaPimConfigMIBGroup }
::= { alcatelIND1PIMMIBCompliances 2 }
-- units of conformance
alaPimsmConfigMIBGroup OBJECT-GROUP
OBJECTS { alaPimsmAdminStatus, alaPimsmMaxRPs,
alaPimsmProbeTime, alaPimsmOldRegisterMessageSupport,
alaPimsmAdminSPTConfig, alaPimsmRPThreshold,
alaPimsmV6AdminStatus, alaPimsmV6SPTConfig,
alaPimsmV6RPSwitchover, alaPimsmBidirStatus,
alaPimsmBidirPeriodicInterval, alaPimsmBidirDFAbort,
alaPimsmNonBidirHelloPeriod, alaPimsmNonBidirHelloMsgsRcvd,
alaPimsmV6BidirStatus, alaPimsmRPHashStatus,
alaPimsmBidirSsmCompat, alaPimsmV6BidirSsmCompat,
alaPimsmBidirFastJoin, alaPimsmV6BidirFastJoin,
alaPimsmAsmFastJoin, alaPimsmV6AsmFastJoin,
alaPimsmSsmFastJoin, alaPimsmV6SsmFastJoin
}
STATUS current
DESCRIPTION
"A collection of objects to support management of global
configuration parameters of PIM Sparse Mode routers."
::= { alcatelIND1PIMMIBGroups 1 }
alaPimdmConfigMIBGroup OBJECT-GROUP
OBJECTS { alaPimdmAdminStatus, alaPimdmStateRefreshTimeToLive,
alaPimdmStateRefreshLimitInterval,
alaPimdmV6AdminStatus, alaPimdmDenseGroupOverrideDynamic,
alaPimdmDenseGroupPrecedence, alaPimdmDenseGroupRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects to support management of global
configuration parameters of PIM Dense Mode routers."
::= { alcatelIND1PIMMIBGroups 2 }
alaPimConfigMIBGroup OBJECT-GROUP
OBJECTS { alaPimBfdStatus,
alaPimBfdAllInterfaceStatus,
alaPimMoFRRStatus,
alaPimMoFRRAllRouteStatus,
alaPimInterfaceBfdStatus,
alaPimMbrAllSourcesStatus,
alaPimMbrOperStatus,
alaPimV6BfdStatus,
alaPimV6BfdAllInterfaceStatus
}
STATUS current
DESCRIPTION
"A collection of objects to support management of global
configuration parameters of PIM routers."
::= { alcatelIND1PIMMIBGroups 3 }
alaPimOptionalGroup OBJECT-GROUP
OBJECTS {
alaPimsmNonBidirHelloAddressType,
alaPimsmNonBidirHelloOrigin
}
STATUS current
DESCRIPTION
" PIM objects to stop the tools from complaining "
::= { alcatelIND1PIMMIBGroups 4 }
alaPimNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
alaPimNonBidirHello
}
STATUS current
DESCRIPTION
" PIM Notification objects "
::= { alcatelIND1PIMMIBGroups 5 }
END