mibs/nokia/aos7/ALCATEL-IND1-PORT-MIB
ALCATEL-IND1-PORT-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, Counter64,
NOTIFICATION-TYPE, MODULE-IDENTITY,
TimeTicks, Integer32, Unsigned32 FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
DisplayString, MacAddress, DateAndTime, TEXTUAL-CONVENTION, RowStatus
FROM SNMPv2-TC
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
ifIndex, ifInErrors, ifOutErrors, ifEntry,
InterfaceIndex FROM IF-MIB
softentIND1Port FROM ALCATEL-IND1-BASE
alclnkaggAggIndex FROM ALCATEL-IND1-LAG-MIB;
alcatelIND1PortMIB MODULE-IDENTITY
LAST-UPDATED "201311220000Z"
ORGANIZATION "Alcatel-Lucent"
CONTACT-INFO
"Please consult with Customer Service to ensure the most appropriate
version of this document is used with the products in question:
Alcatel-Lucent, Enterprise Solutions Division
(Formerly Alcatel Internetworking, Incorporated)
26801 West Agoura Road
Agoura Hills, CA 91301-5122
United States Of America
Telephone: North America +1 800 995 2696
Latin America +1 877 919 9526
Europe +31 23 556 0100
Asia +65 394 7933
All Other +1 818 878 4507
Electronic Mail: support@ind.alcatel.com
World Wide Web: http://alcatel-lucent.com/wps/portal/enterprise
File Transfer Protocol: ftp://ftp.ind.alcatel.com/pub/products/mibs"
DESCRIPTION
"This module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
This group contains the configuration information data
for the Ethernet and Fiber Channel Switching Module.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE"
REVISION "201311220000Z"
DESCRIPTION
"Add support for Fiber Channel interface statistics"
REVISION "201005130000Z"
DESCRIPTION
"Fixed the Notifications to use MIB Module OID.0 as Notifications root."
REVISION "200704030000Z"
DESCRIPTION
"The latest version of this MIB Module."
::= { softentIND1Port 1}
CableState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"an enumerated value used to indicate the status of a cable
pair"
SYNTAX INTEGER {
ok(1),
open(2),
short(3),
openShort(4),
crossTalk(5),
unknown(6)
}
alcatelIND1PortNotifications OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 0 }
alcatelIND1PortMIBObjects OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 1 }
alcatelIND1PortMIBConformance OBJECT IDENTIFIER ::= { alcatelIND1PortMIB 2 }
--
-- alcatelIND1PortMIBObjects
--
esmConfTrap OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 1 }
physicalPort OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 2 }
ddmConfiguration OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 4 }
portViolations OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 5 }
csmConfTrap OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 6 }
interfaceCounters OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 7 }
esmStormTrap OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 8 }
linkAggPort OBJECT IDENTIFIER ::= { alcatelIND1PortMIBObjects 9 }
-- Ethernet Driver object related to Trap *********************
esmDrvTrapDrops OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Partitioned port (separated due to errors)."
::= { esmConfTrap 1 }
-- Dying Gasp Trap Object
alaDyingGaspChassisId OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the chassis id of the chassis whose NI is going down."
::= { csmConfTrap 1 }
alaDyingGaspPowerSupplyType OBJECT-TYPE
SYNTAX INTEGER {
primary (1),
backup (2),
saps (3),
all (4)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the type of the power supply."
::= { csmConfTrap 2 }
alaDyingGaspTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object specifies the time of power failure."
::= { csmConfTrap 3 }
-- Ethernet Storm Violation
esmStormViolationThresholdNotificationType OBJECT-TYPE
SYNTAX INTEGER {
clearViolation(1),
highAlarm(2),
lowAlarm(3)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This type defines the trap genrated by storm control feature for high or low threshold."
::= { esmStormTrap 1 }
esmStormViolationThresholdTrafficType OBJECT-TYPE
SYNTAX INTEGER {
broadcast(1),
multicast(2),
uunicast(3)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This type defines the traffic for which the trap genrated by storm control feature for high or low threshold."
::= { esmStormTrap 2 }
-- Ethernet Driver Tables *****************************
-- EsmConf group. This group contains the configuration
-- information data for the Ethernet Switching Module.
-- Implementation of this group is mandantory.
--
-- Note that this MIB can NOT be used for row creation (this
-- would imply that you could override the actual physical
-- characteristics of the physical card!).
esmConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF EsmConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of ESM Physical Port instances."
::= { physicalPort 1 }
esmConfEntry OBJECT-TYPE
SYNTAX EsmConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A ESM Physical Port entry."
INDEX { ifIndex }
::= { esmConfTable 1 }
EsmConfEntry ::= SEQUENCE {
esmPortSlot
Integer32,
esmPortIF
Integer32,
esmPortAutoSpeed
INTEGER,
esmPortAutoDuplexMode
INTEGER,
esmPortCfgSpeed
INTEGER,
esmPortCfgDuplexMode
INTEGER,
esmPortAdminStatus
INTEGER,
esmPortLinkUpDownTrapEnable
INTEGER,
esmPortCfgMaxFrameSize
Integer32,
esmPortAlias
SnmpAdminString,
esmPortCfgPause
INTEGER,
esmPortCfgAutoNegotiation
INTEGER,
esmPortCfgCrossover
INTEGER,
esmPortCfgHybridActiveType
INTEGER,
esmPortCfgHybridMode
INTEGER,
esmPortOperationalHybridType
INTEGER,
esmPortBcastRateLimitEnable
INTEGER,
esmPortBcastRateLimitType
INTEGER,
esmPortBcastRateLimit
Integer32,
esmPortMcastRateLimitEnable
INTEGER,
esmPortMcastRateLimitType
INTEGER,
esmPortMcastRateLimit
Integer32,
esmPortUucastRateLimitEnable
INTEGER,
esmPortUucastRateLimitType
INTEGER,
esmPortUucastRateLimit
Integer32,
esmPortIngressRateLimitEnable
INTEGER,
esmPortIngressRateLimit
Integer32,
esmPortIngressRateLimitBurst
Integer32,
esmPortEPPEnable
INTEGER,
esmPortEEEEnable
INTEGER,
esmPortIsFiberChannelCapable
INTEGER,
esmPortBcastThresholdAction
INTEGER,
esmPortMcastThresholdAction
INTEGER,
esmPortUucastThresholdAction
INTEGER,
esmPortMinBcastRateLimit
Integer32,
esmPortMinMcastRateLimit
Integer32,
esmPortMinUucastRateLimit
Integer32,
esmPortBcastStormState
INTEGER,
esmPortMcastStormState
INTEGER,
esmPortUucastStormState
INTEGER
}
esmPortSlot OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The physical Slot number for this Ethernet Port.
Slot number has been added to be used by the private Trap."
::= { esmConfEntry 1 }
esmPortIF OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The on-board interface number for this Ethernet Port.
Port Number has been added to be used by the private Trap."
::= { esmConfEntry 2 }
esmPortAutoSpeed OBJECT-TYPE
SYNTAX INTEGER {
speed100(1),
speed10(2),
speedAuto(3),
unknown(4),
speed1000(5),
speed10000(6),
speed40000(7),
speed20000(11),
speed21000(12),
speed2000(13),
speed4000(14),
speed8000(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The automatically detected port line speed
of this ESM port."
::= { esmConfEntry 3 }
esmPortAutoDuplexMode OBJECT-TYPE
SYNTAX INTEGER {
fullDuplex(1),
halfDuplex(2),
autoDuplex(3),
unknown(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The automatically detected port duplex mode
of this ESM port.
Note: GigaEthernet supports only Full duplex mode.
Default value for 10/100 = Half duplex mode."
::= { esmConfEntry 4 }
esmPortCfgSpeed OBJECT-TYPE
SYNTAX INTEGER {
speed100(1),
speed10(2),
speedAuto(3),
speed1000(5),
speed10000(6),
speed40000(7),
speedMax100(8),
speedMax1000(9),
speed2000(13),
speed4000(14),
speed8000(15),
speedMax4000(16),
speedMax8000(17)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The configured port line speed of this ESM port."
::= { esmConfEntry 5 }
esmPortCfgDuplexMode OBJECT-TYPE
SYNTAX INTEGER {
fullDuplex(1),
halfDuplex(2),
autoDuplex(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The configured port duplex mode of this ESM port.
Note: GigaEthernet support only full-duplex."
::= { esmConfEntry 6 }
esmPortAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired state of the interface. The testing(3) state
indicates that no operational packets can be passed. When a
managed system initializes, all interfaces start with
ifAdminStatus in the down(2) state. As a result of either
explicit management action or per configuration information
retained by the managed system, ifAdminStatus is then
changed to either the up(1) or testing(3) states (or remains
in the down(2) state)."
::= { esmConfEntry 7 }
esmPortLinkUpDownTrapEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether linkUp/linkDown traps should be generated
for this interface.
By default, this object should have the value enable(1) for
interfaces which do not operate on 'top' of any other
interface (as defined in the ifStackTable), and disable(2)
otherwise."
::= { esmConfEntry 8 }
esmPortCfgMaxFrameSize OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Configure the value of the maximum frame
size allow.
For 10Mbps the range is upto 1518 bytes.
For ports with speed > 10Mbps the value can extend upto 9216 bytes."
::= { esmConfEntry 11 }
esmPortAlias OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is an 'alias' name for the interface as
specified by a network manager, and provides a non-volatile
'handle' for the interface.
On the first instantiation of an interface, the value of
ifAlias associated with that interface is the zero-length
string. As and when a value is written into an instance of
ifAlias through a network management set operation, then the
agent must retain the supplied value in the ifAlias instance
associated with the same interface for as long as that
interface remains instantiated, including across all re-
initializations/reboots of the network management system,
including those which result in a change of the interface's
ifIndex value.
An example of the value which a network manager might store
in this object for a WAN interface is the (Telco's) circuit
number/identifier of the interface.
Some agents may support write-access only for interfaces
having particular values of ifType. An agent which supports
write access to this object is required to keep the value in
non-volatile storage, but it may limit the length of new
values depending on how much storage is already occupied by
the current values for other interfaces."
::= { esmConfEntry 12 }
esmPortCfgPause OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
enabledXmit(2),
enabledRcv(3),
enabledXmitAndRcv(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This object is used to configure the default
administrative PAUSE mode for this interface.
This object represents the
administratively-configured PAUSE mode for this
interface. If auto-negotiation is not enabled
or is not implemented for the active MAU
attached to this interface, the value of this
object determines the operational PAUSE mode
of the interface whenever it is operating in
full-duplex mode. In this case, a set to this
object will force the interface into the
specified mode.
If auto-negotiation is implemented and enabled
for the MAU attached to this interface, the
PAUSE mode for this interface is determined by
auto-negotiation, and the value of this object
denotes the mode to which the interface will
automatically revert if/when auto-negotiation is
later disabled. For more information on what
pause values will be autonegotiated based on
settings on this object, please refer to the
truth table in the users manual.
Note that the value of this object is ignored
when the interface is not operating in
full-duplex mode."
::= { esmConfEntry 13 }
esmPortCfgAutoNegotiation OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Allow the user to enable or disable the port auto negotiation."
DEFVAL { disable }
::= { esmConfEntry 15 }
esmPortCfgCrossover OBJECT-TYPE
SYNTAX INTEGER {
mdi(1),
mdix(2),
auto(3),
notapplicable(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Allow the user to configure port crossover.
This object is applicable only to copper ports.
For fiber ports notapplicable is returned as a status."
DEFVAL { auto }
::= { esmConfEntry 16 }
esmPortCfgHybridActiveType OBJECT-TYPE
SYNTAX INTEGER {
notapplicable(0),
fiber(1),
copper(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is only applicable to hybrid ports .
It indicates configured active media type.(the operational media
type may be different if esmPortCfgHybridMode is configured to be
preferredFiber or preferredCopper)
For non hybrid ports notapplicable is returned as a status."
::= { esmConfEntry 18 }
esmPortCfgHybridMode OBJECT-TYPE
SYNTAX INTEGER {
notapplicable(0),
preferredCopper(1),
forcedCopper(2),
preferredFiber(3),
forcedFiber(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is only applicable to hybrid ports.
This allows the user the user to configure the media type
with which the port should come up.
The user can configure the port to come as copper only
or fiber only or either fiber/copper
(with preference to one of them)."
DEFVAL { preferredFiber }
::= { esmConfEntry 19 }
esmPortOperationalHybridType OBJECT-TYPE
SYNTAX INTEGER {
none(0),
fiber(1),
copper(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is only applicable to hybrid ports .
It indicates the actual media type that has link up and is or will be
passing traffic. If link is not present the object will return none(0) value."
::= { esmConfEntry 20 }
esmPortBcastRateLimitEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable/disable per port broadcast traffic rate limit. When 'enable' value from
esmPortBcastRateLimit object will be applicable to the ingressing broadcast traffic if
the speed is greater than the limit else the default limit for the speed will be
applied. When it is 'disable' no limit is applied to incoming broadcast traffic which
is limited by the port speed."
DEFVAL { enable }
::= { esmConfEntry 21 }
esmPortBcastRateLimitType OBJECT-TYPE
SYNTAX INTEGER {
mbps(1),
percentage(2),
pps(3),
default(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The unit applicable to the value in esmPortBcastRateLimit object."
DEFVAL { mbps }
::= { esmConfEntry 22 }
esmPortBcastRateLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of the maximum broadcast traffic that can flow
through the port. The actual value depends on the port speed
if the configured values is greater than the current port speed.
It is mandatory to set esmPortBcastRateLimitType object along with
esmPortBcastRateLimit object to set the broadcast rate limit."
::= { esmConfEntry 23 }
esmPortMcastRateLimitEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable/disable per port multicast traffic rate limit. When 'enable' value from
esmPortMcastRateLimit object will be applicable to the ingressing multicast traffic if
the speed is greater than the limit else the default limit for the speed will be
applied. When it is 'disable' no limit is applied to incoming multicast traffic which
is limited by the port speed."
DEFVAL { enable }
::= { esmConfEntry 24 }
esmPortMcastRateLimitType OBJECT-TYPE
SYNTAX INTEGER {
mbps(1),
percentage(2),
pps(3),
default(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The unit applicable to the value in esmPortMcastRateLimit object."
DEFVAL { mbps }
::= { esmConfEntry 25 }
esmPortMcastRateLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of the maximum multicast traffic that can flow
through the port. The actual value depends on the port speed
if the configured values is greater than the current port speed.
It is mandatory to set esmPortMcastRateLimitType object along with
esmPortMcastRateLimit object to set the multicast rate limit."
::= { esmConfEntry 26 }
esmPortUucastRateLimitEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable/disable per port unknown unicast traffic rate limit. When 'enable' value from
esmPortUucastRateLimit object will be applicable to the ingressing unknown unicast traffic if
the speed is greater than the limit else the default limit for the speed will be
applied. When it is 'disable' no limit is applied to incoming unknown unicast traffic which
is limited by the port speed."
DEFVAL { enable }
::= { esmConfEntry 27 }
esmPortUucastRateLimitType OBJECT-TYPE
SYNTAX INTEGER {
mbps(1),
percentage(2),
pps(3),
default(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The unit applicable to the value in esmPortUucastRate object."
DEFVAL { mbps }
::= { esmConfEntry 28 }
esmPortUucastRateLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of the maximum unknown unicast traffic that can flow
through the port. The actual value depends on the port speed
if the configured values is greater than the current port speed.
It is mandatory to set esmPortUucastRateLimitType object along with
esmPortUucastRateLimit object to set the unknown unicast rate limit."
::= { esmConfEntry 29 }
esmPortIngressRateLimitEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Enable/disable per port ingress traffic rate limit. When 'enable' value from
esmPortIngressRate object will be applicable to the ingressing traffic (BC, MC, UUC) if
the speed is greater than the limit else the default limit for the speed will be
applied. When it is 'disable' no limit is applied to incoming traffic which
is limited by the port speed."
DEFVAL { enable }
::= { esmConfEntry 30 }
esmPortIngressRateLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of the maximum ingress traffic that can flow
through the port. The actual value depends on the port speed
if the configured value is greater than the current port speed."
::= { esmConfEntry 31 }
esmPortIngressRateLimitBurst OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of ingress traffic burst size in Mbits."
::= { esmConfEntry 32 }
esmPortEPPEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"use for port diagnostics"
DEFVAL { disable }
::= { esmConfEntry 33 }
esmPortEEEEnable OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"10Gbase-T Energy Efficent Ethernet port parameter."
DEFVAL { disable }
::= { esmConfEntry 34 }
esmPortIsFiberChannelCapable OBJECT-TYPE
SYNTAX INTEGER {
yes(1),
no(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The port can be configured as Fiber Channel interface (yes) or can
not be configured as Fiber Channel interface."
DEFVAL { no }
::= { esmConfEntry 35 }
esmPortBcastThresholdAction OBJECT-TYPE
SYNTAX INTEGER {
default(1),
trap(2),
shutdown(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The port can be configured to send trap/shutdown if
the threshold limit is crossed for Bcast Frames"
DEFVAL { default }
::= { esmConfEntry 36 }
esmPortMcastThresholdAction OBJECT-TYPE
SYNTAX INTEGER {
default(1),
trap(2),
shutdown(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The port can be configured to send trap/shutdown if
the threshold limit is crossed for Mcast Frames"
DEFVAL { default }
::= { esmConfEntry 37 }
esmPortUucastThresholdAction OBJECT-TYPE
SYNTAX INTEGER {
default(1),
trap(2),
shutdown(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The port can be configured to send trap/shutdown if
the threshold limit is crossed Unknown Unicast Frames"
DEFVAL { default }
::= { esmConfEntry 38 }
esmPortMinBcastRateLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of low threshold for bcast."
::= { esmConfEntry 39 }
esmPortMinMcastRateLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of low threshold for mcast."
::= { esmConfEntry 40 }
esmPortMinUucastRateLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of low threshold for uucast."
::= { esmConfEntry 41 }
esmPortBcastStormState OBJECT-TYPE
SYNTAX INTEGER {
normal(1),
storm(2),
trap(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the port for broadcast Storm Control."
DEFVAL { normal }
::= { esmConfEntry 42 }
esmPortMcastStormState OBJECT-TYPE
SYNTAX INTEGER {
normal(1),
storm(2),
trap(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the port for multi-cast Storm Control."
DEFVAL { normal }
::= { esmConfEntry 43 }
esmPortUucastStormState OBJECT-TYPE
SYNTAX INTEGER {
normal(1),
storm(2),
trap(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the port for uucast Storm Control."
DEFVAL { normal }
::= { esmConfEntry 44 }
-- The Ethernet Statistics Group
--
-- The ethernet statistics group contains statistics
-- measured by the probe for each monitored interface on
-- this device. These statistics take the form of free
-- running counters that start from zero when a valid entry
-- is created.
--
-- This group currently has statistics defined only for
-- Ethernet interfaces. Each alcetherStatsEntry contains
-- statistics for one Ethernet interface. The probe must
-- create one alcetherStats entry for each monitored Ethernet
-- interface on the device.
alcetherStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlcetherStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Ethernet statistics entries."
::= { physicalPort 2 }
alcetherStatsEntry OBJECT-TYPE
SYNTAX AlcetherStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of statistics kept for a particular
Ethernet interface. As an example, an instance of the
etherStatsPkts object might be named alcetherStatsPkts.1"
INDEX { ifIndex }
::= { alcetherStatsTable 1 }
AlcetherStatsEntry ::= SEQUENCE {
alcetherClearStats INTEGER,
alcetherLastClearStats TimeTicks,
alcetherStatsCRCAlignErrors Counter64,
alcetherStatsRxUndersizePkts Counter64,
alcetherStatsTxUndersizePkts Counter64,
alcetherStatsTxOversizePkts Counter64,
alcetherStatsRxJabbers Counter64,
alcetherStatsRxCollisions Counter64,
alcetherStatsTxCollisions Counter64,
alcetherStatsPkts64Octets Counter64,
alcetherStatsPkts65to127Octets Counter64,
alcetherStatsPkts128to255Octets Counter64,
alcetherStatsPkts256to511Octets Counter64,
alcetherStatsPkts512to1023Octets Counter64,
alcetherStatsPkts1024to1518Octets Counter64,
gigaEtherStatsPkts1519to4095Octets Counter64,
gigaEtherStatsPkts4096to9215Octets Counter64,
alcetherStatsPkts1519to2047Octets Counter64,
alcetherStatsPkts2048to4095Octets Counter64,
alcetherStatsPkts4096Octets Counter64,
alcetherStatsRxGiantPkts Counter64,
alcetherStatsRxDribbleNibblePkts Counter64,
alcetherStatsRxLongEventPkts Counter64,
alcetherStatsRxVlanTagPkts Counter64,
alcetherStatsRxControlPkts Counter64,
alcetherStatsRxLenChkErrPkts Counter64,
alcetherStatsRxCodeErrPkts Counter64,
alcetherStatsRxDvEventPkts Counter64,
alcetherStatsRxPrevPktDropped Counter64,
alcetherStatsTx64Octets Counter64,
alcetherStatsTx65to127Octets Counter64,
alcetherStatsTx128to255Octets Counter64,
alcetherStatsTx256to511Octets Counter64,
alcetherStatsTx512to1023Octets Counter64,
alcetherStatsTx1024to1518Octets Counter64,
alcetherStatsTx1519to2047Octets Counter64,
alcetherStatsTx2048to4095Octets Counter64,
alcetherStatsTx4096Octets Counter64,
alcetherStatsTxRetryCount Counter64,
alcetherStatsTxVlanTagPkts Counter64,
alcetherStatsTxControlPkts Counter64,
alcetherStatsTxLatePkts Counter64,
alcetherStatsTxTotalBytesOnWire Counter64,
alcetherStatsTxLenChkErrPkts Counter64,
alcetherStatsTxExcDeferPkts Counter64
}
alcetherClearStats OBJECT-TYPE
SYNTAX INTEGER
{ default(0),
reset(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Used to Clear all Statistics counters.
By default, this object contains zero value."
::= { alcetherStatsEntry 1 }
alcetherLastClearStats OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of SysUpTime at the time of all
the statistics counters are cleared.
By default, this object contains a zero value."
::= { alcetherStatsEntry 2 }
alcetherStatsCRCAlignErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and 1518
octets, inclusive, but but had either a bad
Frame Check Sequence (FCS) with an integral
number of octets (FCS Error) or a bad FCS with
a non-integral number of octets (Alignment Error)."
::= { alcetherStatsEntry 3 }
alcetherStatsRxUndersizePkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets received that were
less than 64 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed."
::= { alcetherStatsEntry 4 }
alcetherStatsTxUndersizePkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets transmitted that were
less than 64 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed."
::= { alcetherStatsEntry 5 }
alcetherStatsTxOversizePkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets transmitted that were
longer than 1518 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed."
::= { alcetherStatsEntry 6 }
alcetherStatsRxJabbers OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets received that were
longer than 1518 octets (excluding framing bits,
but including FCS octets), and had either a bad
Frame Check Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment Error).
Note that this definition of jabber is different
than the definition in IEEE-802.3 section 8.2.1.5
(10BASE5) and section 10.3.1.4 (10BASE2). These
documents define jabber as the condition where any
packet exceeds 20 ms. The allowed range to detect
jabber is between 20 ms and 150 ms."
::= { alcetherStatsEntry 7 }
alcetherStatsRxCollisions OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The best estimate of the total number of collisions
on this Ethernet segment (in reception).
Only for Ethernet Interfaces.
The value returned will depend on the location of
the RMON probe. Section 8.2.1.3 (10BASE-5) and
section 10.3.1.3 (10BASE-2) of IEEE standard 802.3
states that a station must detect a collision, in
the receive mode, if three or more stations are
transmitting simultaneously. A repeater port must
detect a collision when two or more stations are
transmitting simultaneously. Thus a probe placed on
a repeater port could record more collisions than a
probe connected to a station on the same segment
would.
Probe location plays a much smaller role when
considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE
standard 802.3 defines a collision as the
simultaneous presence of signals on the DO and RD
circuits (transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus probes
placed on a station and a repeater, should report
the same number of collisions.
Note also that an RMON probe inside a repeater
should ideally report collisions between the
repeater and one or more other hosts (transmit
collisions as defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments to which
the repeater is connected."
::= { alcetherStatsEntry 8 }
alcetherStatsTxCollisions OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The best estimate of the total number of collisions
on this Ethernet segment (in transmition).
Only for Ethernet Interfaces.
The value returned will depend on the location of
the RMON probe. Section 8.2.1.3 (10BASE-5) and
section 10.3.1.3 (10BASE-2) of IEEE standard 802.3
states that a station must detect a collision, in
the receive mode, if three or more stations are
transmitting simultaneously. A repeater port must
detect a collision when two or more stations are
transmitting simultaneously. Thus a probe placed on
a repeater port could record more collisions than a
probe connected to a station on the same segment
would.
Probe location plays a much smaller role when
considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE
standard 802.3 defines a collision as the
simultaneous presence of signals on the DO and RD
circuits (transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus probes
placed on a station and a repeater, should report
the same number of collisions.
Note also that an RMON probe inside a repeater
should ideally report collisions between the
repeater and one or more other hosts (transmit
collisions as defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments to which
the repeater is connected."
::= { alcetherStatsEntry 9 }
alcetherStatsPkts64Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets (including bad
packets) received that were 64 octets in length
(excluding framing bits but including FCS octets)."
::= { alcetherStatsEntry 10 }
alcetherStatsPkts65to127Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets (including bad
packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS octets)."
::= { alcetherStatsEntry 11 }
alcetherStatsPkts128to255Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets (including bad
packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS octets)."
::= { alcetherStatsEntry 12 }
alcetherStatsPkts256to511Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets (including bad
packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS octets)."
::= { alcetherStatsEntry 13 }
alcetherStatsPkts512to1023Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets (including bad
packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS octets)."
::= { alcetherStatsEntry 14 }
alcetherStatsPkts1024to1518Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets (including bad
packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS octets).
For both Ethernet and GigaEthernet."
::= { alcetherStatsEntry 15 }
gigaEtherStatsPkts1519to4095Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets (including bad
packets) received that were between
1519 and 4095 octets in length inclusive
(excluding framing bits but including FCS octets).
Only for GigaEthernet interfaces"
::= { alcetherStatsEntry 16 }
gigaEtherStatsPkts4096to9215Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets (including bad
packets) received that were between
4096 and 9215 octets in length inclusive
(excluding framing bits but including FCS octets).
Only for GigaEthernet interfaces"
::= { alcetherStatsEntry 17 }
alcetherStatsPkts1519to2047Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames(including error packets) received
that were between 1519 and 2047 bytes in length inclusive
(excluding framing bits but including FCS bytes).
"
::= { alcetherStatsEntry 18 }
alcetherStatsPkts2048to4095Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames(including error packets) received
that were between 2048 and 4095 bytes in length inclusive
(excluding framing bits but including FCS bytes).
"
::= { alcetherStatsEntry 19 }
alcetherStatsPkts4096Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames(including error packets) received
that were greater than or equal to 4096 bytes in length inclusive
(excluding framing bits but including FCS bytes).
"
::= { alcetherStatsEntry 20 }
alcetherStatsRxGiantPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames that are greater than the specified
Max length value, with a valid CRC, dropped because too long.
"
::= { alcetherStatsEntry 21 }
alcetherStatsRxDribbleNibblePkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames for which a dribble nibble has been
received and CRC is correct.
"
::= { alcetherStatsEntry 22 }
alcetherStatsRxLongEventPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames for which the Carrier sense exceeds
50000 bit times for 10 Mbits/sec or 80000 bit times for
100 Mbits/sec."
::= { alcetherStatsEntry 23 }
alcetherStatsRxVlanTagPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames for which Type/Length field
contains the VLAN protocol identifier (0x8100). "
::= { alcetherStatsEntry 24 }
alcetherStatsRxControlPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames that were recognized as control frames."
::= { alcetherStatsEntry 25 }
alcetherStatsRxLenChkErrPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames for which the frame length field value
in the Type/Length field does not match the actual data bytes
length and is NOT a type field."
::= { alcetherStatsEntry 26 }
alcetherStatsRxCodeErrPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames for which one or more nibbles were
signaled as errors during reception of the frame."
::= { alcetherStatsEntry 27 }
alcetherStatsRxDvEventPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames for which a RX_DV event (packet not
too long enough to be valid packet) has been seen before the
correct frame."
::= { alcetherStatsEntry 28 }
alcetherStatsRxPrevPktDropped OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames for which a packet has been dropped
(because of too small IFG) before the correct frame."
::= { alcetherStatsEntry 29 }
alcetherStatsTx64Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames of 64 bytes."
::= { alcetherStatsEntry 30 }
alcetherStatsTx65to127Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were between
65 and 127 bytes in length inclusive (excluding framing bits
but including FCS bytes)."
::= { alcetherStatsEntry 31 }
alcetherStatsTx128to255Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were between
128 and 255 bytes in length inclusive (excluding framing bits
but including FCS bytes)."
::= { alcetherStatsEntry 32 }
alcetherStatsTx256to511Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were between
256 and 511 bytes in length inclusive (excluding framing bits
but including FCS bytes)."
::= { alcetherStatsEntry 33 }
alcetherStatsTx512to1023Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were between
512 and 1023 bytes in length inclusive (excluding framing bits
but including FCS bytes)."
::= { alcetherStatsEntry 34 }
alcetherStatsTx1024to1518Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were between
1024 and 1518 bytes in length inclusive (excluding framing bits
but including FCS bytes)."
::= { alcetherStatsEntry 35 }
alcetherStatsTx1519to2047Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were between
1519 and 2047 bytes in length inclusive (excluding framing bits
but including FCS bytes)."
::= { alcetherStatsEntry 36 }
alcetherStatsTx2048to4095Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were between
2048 and 4095 bytes in length inclusive (excluding framing bits
but including FCS bytes)."
::= { alcetherStatsEntry 37 }
alcetherStatsTx4096Octets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were greater than
or equal to 4096 bytes in length and less than Max frame length
(excluding framing bits but including FCS bytes)."
::= { alcetherStatsEntry 38 }
alcetherStatsTxRetryCount OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of collisions that the frames faced during
transmission attempts."
::= { alcetherStatsEntry 39 }
alcetherStatsTxVlanTagPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames for which Type/Length field contains the
VLAN protocol identifier (0x8100)."
::= { alcetherStatsEntry 40 }
alcetherStatsTxControlPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames that were recognised as control frames."
::= { alcetherStatsEntry 41 }
alcetherStatsTxLatePkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of late collisions that occured beyond the collision window."
::= { alcetherStatsEntry 42 }
alcetherStatsTxTotalBytesOnWire OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of bytes transmitted on wire, including all bytes from collided
attempts."
::= { alcetherStatsEntry 43 }
alcetherStatsTxLenChkErrPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of transmitted frames for which the frame length field value
in the Type/Length field does not match the actual data bytes length and
is NOT a Type field."
::= { alcetherStatsEntry 44 }
alcetherStatsTxExcDeferPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of frames that were deferred in excess of 6071 nibble-times
in 100 Mbps, 24287 bit-times in 10 Mbps mode. These frames are dropped.(This
stat is only in case of Half duplex and excessive defer bit reset)."
::= { alcetherStatsEntry 45 }
-- Link Aggregation Statistics *****************************
-- The Link Aggregation Statistics Group
--
-- The link aggregation statistics group contains statistics
-- measured by the probe for each monitored Link Aggregation (lag)
-- on this device. These statistics take the form of free
-- running counters that start from zero when a valid entry
-- is created.
--
-- This group currently has statistics defined only for
-- lag interfaces. Each alcLagStatsEntry contains
-- statistics for one link aggregation interface. The probe must
-- create one alcLagStats entry for each monitored link aggregation
-- interface on the device.
alcLagStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlcLagStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Link Aggregation statistics entries."
::= { linkAggPort 1 }
alcLagStatsEntry OBJECT-TYPE
SYNTAX AlcLagStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of statistics kept for a particular
Link Aggregation interface. alclnkaggAggIndex is defined
in alclnkaggAggTable; it is of SYNTAX InterfaceIndex
(aka ifIndex) starting at value 40000001 for link agg 1.
Index values received outside of the range for link aggregation
interfaces will return an error."
INDEX { alclnkaggAggIndex }
::= { alcLagStatsTable 1 }
AlcLagStatsEntry ::= SEQUENCE {
alcLagClearStats INTEGER
}
alcLagClearStats OBJECT-TYPE
SYNTAX INTEGER
{
none(0),
reset(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Used to Clear all Link Aggregation Statistics counters. New stats collection starts immediately.
No meaningful read on this object."
DEFVAL { none }
::= { alcLagStatsEntry 1 }
-- Ethernet Driver Tables *****************************
-- EsmHybridConf table contains the configuration
-- information about the configured inactive media for the
-- hybrid port only.
-- Implementation of this group is mandantory.
--
-- Note that entries in this MIB Table can NOT be created by the user, only modified
esmHybridConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF EsmHybridConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of inactive hybrid port instances."
::= { physicalPort 3 }
esmHybridConfEntry OBJECT-TYPE
SYNTAX EsmHybridConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A ESM Physical Port entry."
INDEX { ifIndex }
::= { esmHybridConfTable 1 }
EsmHybridConfEntry ::= SEQUENCE {
esmHybridPortCfgSpeed
INTEGER,
esmHybridPortCfgDuplexMode
INTEGER,
esmHybridPortCfgAutoNegotiation
INTEGER,
esmHybridPortCfgCrossover
INTEGER,
esmHybridPortCfgFlow
INTEGER,
esmHybridPortCfgInactiveType
INTEGER
}
esmHybridPortCfgSpeed OBJECT-TYPE
SYNTAX INTEGER {
speed100(1),
speed10(2),
speedAuto(3),
speed1000(5),
speed10000(6),
speedMax100(8),
speedMax1000(9)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The configured port line speed of this ESM port."
::= { esmHybridConfEntry 1 }
esmHybridPortCfgDuplexMode OBJECT-TYPE
SYNTAX INTEGER {
fullDuplex(1),
halfDuplex(2),
autoDuplex(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The configured port duplex mode of this ESM port.
Note: GigaEthernet support only full-duplex."
::= { esmHybridConfEntry 2 }
esmHybridPortCfgAutoNegotiation OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Allow the user to enable or disable the port auto negotiation."
DEFVAL { disable }
::= { esmHybridConfEntry 3 }
esmHybridPortCfgCrossover OBJECT-TYPE
SYNTAX INTEGER {
mdi(1),
mdix(2),
auto(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Allow the user to configure port crossover."
DEFVAL { auto }
::= { esmHybridConfEntry 4 }
esmHybridPortCfgFlow OBJECT-TYPE
SYNTAX INTEGER {
disable(1),
enabledXmit(2),
enabledRcv(3),
enabledXmitAndRcv(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used for flow control of hybrid ports. It is similar to the dot3PauseAdminMode
object in dot3PauseTable. It is used to configure pause for fiber media."
DEFVAL { disable }
::= { esmHybridConfEntry 5 }
esmHybridPortCfgInactiveType OBJECT-TYPE
SYNTAX INTEGER {
fiber(1),
copper(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is only applicable to hybrid ports .
It indicates the configured inactive media type."
::= { esmHybridConfEntry 6 }
-- Digital Diagnostics Monitoring (DDM) **************************
ddmConfig OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables/disables DDM software feature in the system."
DEFVAL { disable }
::= { ddmConfiguration 1 }
ddmTrapConfig OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects enables/disables traps for DDM warning/alarm threshold violations."
DEFVAL { disable }
::= { ddmConfiguration 2 }
ddmNotificationType OBJECT-TYPE
SYNTAX INTEGER
{
clearViolation(1),
highAlarm(2),
highWarning(3),
lowWarning(4),
lowAlarm(5)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"This object defines the trap type for monitored DDM parameters."
::= { ddmConfiguration 3 }
ddmInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF DdmEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The ddmInfoTable has an entry for each SFP/XFP in the
system that supports Digital Diagnostic Monitoring (DDM). The table is
indexed by ifIndex. Each row in this table is dynamically added
and removed internally by the system based on the presence or absence
of DDM capable SFP/XFP components."
::= { physicalPort 5 }
ddmInfoEntry OBJECT-TYPE
SYNTAX DdmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a particular SFP/XFP that supports Digital
Diagnostic Monitoring.
Entries are created and deleted internally by the system."
INDEX { ifIndex }
::= { ddmInfoTable 1}
DdmEntry ::= SEQUENCE
{
ddmTemperature Integer32,
ddmTempLowWarning Integer32,
ddmTempLowAlarm Integer32,
ddmTempHiWarning Integer32,
ddmTempHiAlarm Integer32,
ddmSupplyVoltage Integer32,
ddmSupplyVoltageLowWarning Integer32,
ddmSupplyVoltageLowAlarm Integer32,
ddmSupplyVoltageHiWarning Integer32,
ddmSupplyVoltageHiAlarm Integer32,
ddmTxBiasCurrent Integer32,
ddmTxBiasCurrentLowWarning Integer32,
ddmTxBiasCurrentLowAlarm Integer32,
ddmTxBiasCurrentHiWarning Integer32,
ddmTxBiasCurrentHiAlarm Integer32,
ddmTxOutputPower Integer32,
ddmTxOutputPowerLowWarning Integer32,
ddmTxOutputPowerLowAlarm Integer32,
ddmTxOutputPowerHiWarning Integer32,
ddmTxOutputPowerHiAlarm Integer32,
ddmRxOpticalPower Integer32,
ddmRxOpticalPowerLowWarning Integer32,
ddmRxOpticalPowerLowAlarm Integer32,
ddmRxOpticalPowerHiWarning Integer32,
ddmRxOpticalPowerHiAlarm Integer32
}
ddmTemperature OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTemperature indicates the current temperature
of the SFP/XFP in 1000s of degrees Celsius.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 1 }
ddmTempLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTempLowWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 2 }
ddmTempLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTempLowAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 3 }
ddmTempHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTempHiWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 4 }
ddmTempHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTempHiAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 5 }
ddmSupplyVoltage OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltage indicates the current supply
voltage of the SFP/XFP in 1000s of Volts (V).
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 6 }
ddmSupplyVoltageLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltageLowWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 7 }
ddmSupplyVoltageLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltageLowAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 8 }
ddmSupplyVoltageHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltageHiWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 9 }
ddmSupplyVoltageHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltageHiAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 10 }
ddmTxBiasCurrent OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrent indicates the current Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA).
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 11 }
ddmTxBiasCurrentLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrentLowWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 12 }
ddmTxBiasCurrentLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrentLowAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 13 }
ddmTxBiasCurrentHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrentHiWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 14 }
ddmTxBiasCurrentHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrentHiAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 15 }
ddmTxOutputPower OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPower indicates the current Output
Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 16 }
ddmTxOutputPowerLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPowerLowWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 17 }
ddmTxOutputPowerLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPowerLowAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 18 }
ddmTxOutputPowerHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPowerHiWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 19 }
ddmTxOutputPowerHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPowerHiAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 20 }
ddmRxOpticalPower OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPower indicates the current Received
Optical Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 21 }
ddmRxOpticalPowerLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPowerLowWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 22 }
ddmRxOpticalPowerLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPowerLowAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 23 }
ddmRxOpticalPowerHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPowerHiWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 24 }
ddmRxOpticalPowerHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPowerHiAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmInfoEntry 25 }
ddmPortInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF DdmPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ddmPortInfoTable has an entry for each SFP/XFP in the
system that supports Digital Diagnostic Monitoring (DDM). The table is
indexed by ifIndex and port channel. Each row in this table is
dynamically added
and removed internally by the system based on the presence or absence
of DDM capable SFP/XFP components."
::= { physicalPort 6 }
ddmPortInfoEntry OBJECT-TYPE
SYNTAX DdmPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a particular SFP/XFP that supports Digital
Diagnostic Monitoring.
Entries are created and deleted internally by the system."
INDEX { ifIndex,
ddmPortChannel }
::= { ddmPortInfoTable 1}
DdmPortEntry ::= SEQUENCE
{
ddmPortChannel Integer32,
ddmPortTemperature Integer32,
ddmPortTempLowWarning Integer32,
ddmPortTempLowAlarm Integer32,
ddmPortTempHiWarning Integer32,
ddmPortTempHiAlarm Integer32,
ddmPortSupplyVoltage Integer32,
ddmPortSupplyVoltageLowWarning Integer32,
ddmPortSupplyVoltageLowAlarm Integer32,
ddmPortSupplyVoltageHiWarning Integer32,
ddmPortSupplyVoltageHiAlarm Integer32,
ddmPortTxBiasCurrent Integer32,
ddmPortTxBiasCurrentLowWarning Integer32,
ddmPortTxBiasCurrentLowAlarm Integer32,
ddmPortTxBiasCurrentHiWarning Integer32,
ddmPortTxBiasCurrentHiAlarm Integer32,
ddmPortTxOutputPower Integer32,
ddmPortTxOutputPowerLowWarning Integer32,
ddmPortTxOutputPowerLowAlarm Integer32,
ddmPortTxOutputPowerHiWarning Integer32,
ddmPortTxOutputPowerHiAlarm Integer32,
ddmPortRxOpticalPower Integer32,
ddmPortRxOpticalPowerLowWarning Integer32,
ddmPortRxOpticalPowerLowAlarm Integer32,
ddmPortRxOpticalPowerHiWarning Integer32,
ddmPortRxOpticalPowerHiAlarm Integer32
}
ddmPortChannel OBJECT-TYPE
SYNTAX Integer32 (1..4)
UNITS "QSFP/SFP channel number"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The channel number of the data that is being read. In the case
of a QSFP there will be 4 10 gigabyte channels, for SFP/XFP there
will only be one."
::= { ddmPortInfoEntry 1 }
ddmPortTemperature OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTemperature indicates the current temperature
of the SFP/XFP in 1000s of degrees Celsius.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 2 }
ddmPortTempLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTempLowWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 3 }
ddmPortTempLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTempLowAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 4 }
ddmPortTempHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTempHiWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 5 }
ddmPortTempHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -150000..150000)
UNITS "thousandth of a degree celcius"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTempHiAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 6 }
ddmPortSupplyVoltage OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltage indicates the current supply
voltage of the SFP/XFP in 1000s of Volts (V).
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 7 }
ddmPortSupplyVoltageLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltageLowWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 8 }
ddmPortSupplyVoltageLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltageLowAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 9 }
ddmPortSupplyVoltageHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltageHiWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 10 }
ddmPortSupplyVoltageHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a volt"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmSupplyVoltageHiAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 11 }
ddmPortTxBiasCurrent OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrent indicates the current Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA).
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 12 }
ddmPortTxBiasCurrentLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrentLowWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 13 }
ddmPortTxBiasCurrentLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrentLowAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 14 }
ddmPortTxBiasCurrentHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrentHiWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 15 }
ddmPortTxBiasCurrentHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | 0..10000)
UNITS "thousandth of a milli-Ampere"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxBiasCurrentHiAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 16 }
ddmPortTxOutputPower OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPower indicates the current Output
Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 17 }
ddmPortTxOutputPowerLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPowerLowWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 18 }
ddmPortTxOutputPowerLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPowerLowAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 19 }
ddmPortTxOutputPowerHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPowerHiWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 20 }
ddmPortTxOutputPowerHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmTxOutputPowerHiAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 21 }
ddmPortRxOpticalPower OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPower indicates the current Received
Optical Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 22 }
ddmPortRxOpticalPowerLowWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPowerLowWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 23 }
ddmPortRxOpticalPowerLowAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPowerLowAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 24 }
ddmPortRxOpticalPowerHiWarning OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPowerHiWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 25 }
ddmPortRxOpticalPowerHiAlarm OBJECT-TYPE
SYNTAX Integer32 (-200000 | -40000..10000)
UNITS "thousandth of a dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ddmRxOpticalPowerHiAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable."
::= { ddmPortInfoEntry 26 }
-- The Fiber Channel Statistics Group
--
-- The fiber channel statistics group contains statistics
-- measured by the probe for each monitored interface on
-- this device. These statistics take the form of free
-- running counters that start from zero when a valid entry
-- is created.
--
-- This group currently has statistics defined only for
-- Fiber Channel interfaces. Each alcfcStatsEntry contains
-- statistics for one Fiber Channel interface. The probe must
-- create one alcfcStats entry for each monitored Fiber Channel
-- interface on the device.
alcfcStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlcfcStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Fiber Channel statistics entries."
::= { physicalPort 7 }
alcfcStatsEntry OBJECT-TYPE
SYNTAX AlcfcStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of statistics kept for a particular
Fiber Channel interface. As an example, an instance of the
fcStatsPkts object might be named alcfcStatsPkts.1"
INDEX { ifIndex }
::= { alcfcStatsTable 1 }
AlcfcStatsEntry ::= SEQUENCE {
alcfcClearStats INTEGER,
alcfcLastClearStats TimeTicks,
alcfcStatsRxUndersizePkts Counter64,
alcfcStatsTxBBCreditZeros Counter64,
alcfcStatsRxBBCreditZeros Counter64,
alcfcStatsLinkFailures Counter64,
alcfcStatsLossofSynchs Counter64,
alcfcStatsLossofSignals Counter64,
alcfcStatsPrimSeqProtocolErrors Counter64,
alcfcStatsInvalidTxWords Counter64,
alcfcStatsInvalidCRCs Counter64,
alcfcStatsInvalidOrderedSets Counter64,
alcfcStatsFrameTooLongs Counter64,
alcfcStatsDelimiterErrors Counter64,
alcfcStatsEncodingDisparityErrors Counter64,
alcfcStatsOtherErrors Counter64
}
alcfcClearStats OBJECT-TYPE
SYNTAX INTEGER
{ default(0),
reset(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Used to Clear all Statistics counters.
By default, this object contains zero value."
::= { alcfcStatsEntry 1 }
alcfcLastClearStats OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of SysUpTime at the time of all
the statistics counters are cleared.
By default, this object contains a zero value."
::= { alcfcStatsEntry 2 }
alcfcStatsRxUndersizePkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of packets received that were
less than 36 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed."
::= { alcfcStatsEntry 3 }
alcfcStatsTxBBCreditZeros OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of transitions in/out of the buffer-to-buffer
credit zero state."
::= { alcfcStatsEntry 6 }
alcfcStatsRxBBCreditZeros OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times RX BBCredit drops to zero."
::= { alcfcStatsEntry 7 }
alcfcStatsLinkFailures OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of link failures."
::= { alcfcStatsEntry 8 }
alcfcStatsLossofSynchs OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of loss of word-sync detected."
::= { alcfcStatsEntry 9 }
alcfcStatsLossofSignals OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of loss of signals detected."
::= { alcfcStatsEntry 10 }
alcfcStatsPrimSeqProtocolErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of primitive sequence protocol errors detected."
::= { alcfcStatsEntry 11 }
alcfcStatsInvalidTxWords OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of invalid transmission words. This includes
invalid ordered sets and invalid data words."
::= { alcfcStatsEntry 12 }
alcfcStatsInvalidCRCs OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of frames received with an invalid CRC."
::= { alcfcStatsEntry 13 }
alcfcStatsInvalidOrderedSets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of invalid ordered sets received at this port."
::= { alcfcStatsEntry 14 }
alcfcStatsFrameTooLongs OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of frames received at this port for which the
frame length was greater than what was agreed to in
FLOGI/PLOGI."
::= { alcfcStatsEntry 15 }
alcfcStatsDelimiterErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of invalid delimiters received"
::= { alcfcStatsEntry 16 }
alcfcStatsEncodingDisparityErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of detected running disparity at 10b/8b level."
::= { alcfcStatsEntry 17 }
alcfcStatsOtherErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of errors detected but not counted by any other
error counter. This only includes RX frames drops due to zero
RX BBCredits"
::= { alcfcStatsEntry 18 }
-- Ethernet Driver Trap *********************
esmDrvTrapDropsLink NOTIFICATION-TYPE
OBJECTS {
esmPortSlot,
esmPortIF,
ifInErrors,
ifOutErrors,
esmDrvTrapDrops
}
STATUS current
DESCRIPTION
"When the Ethernet code drops the link because of
excessive errors, a Trap is sent."
::= { alcatelIND1PortNotifications 1 }
-- DDM TRAPS ****************************
ddmTemperatureThresholdViolated NOTIFICATION-TYPE
OBJECTS {
ifIndex,
ddmNotificationType,
ddmTemperature
}
STATUS current
DESCRIPTION
"This object notifies management station if an SFP/XFP/SFP+ temperature has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ temperature."
::= { alcatelIND1PortNotifications 2 }
ddmVoltageThresholdViolated NOTIFICATION-TYPE
OBJECTS {
ifIndex,
ddmNotificationType,
ddmSupplyVoltage
}
STATUS current
DESCRIPTION
"This object notifies management station if an SFP/XFP/SFP+ supply voltage has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ supply voltage."
::= { alcatelIND1PortNotifications 3 }
ddmCurrentThresholdViolated NOTIFICATION-TYPE
OBJECTS {
ifIndex,
ddmNotificationType,
ddmTxBiasCurrent
}
STATUS current
DESCRIPTION
"This object notifies management station if an SFP/XFP/SFP+ Tx bias current has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ Tx bias current."
::= { alcatelIND1PortNotifications 4 }
ddmTxPowerThresholdViolated NOTIFICATION-TYPE
OBJECTS {
ifIndex,
ddmNotificationType,
ddmTxOutputPower
}
STATUS current
DESCRIPTION
"This object notifies management station if an SFP/XFP/SFP+ Tx output power has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ Tx output power."
::= { alcatelIND1PortNotifications 5 }
ddmRxPowerThresholdViolated NOTIFICATION-TYPE
OBJECTS {
ifIndex,
ddmNotificationType,
ddmRxOpticalPower
}
STATUS current
DESCRIPTION
"This object notifies management station if an SFP/XFP/SFP+ Rx optical power has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ Rx optical power."
::= { alcatelIND1PortNotifications 6 }
--
-- The Port Violation Table shows if the table has any violations set
--
portViolationTable OBJECT-TYPE
SYNTAX SEQUENCE OF PortViolationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the port Violations per port."
::= { portViolations 1 }
portViolationEntry OBJECT-TYPE
SYNTAX PortViolationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Port Violation Entry. The entries in this table are indexed
by 3 units,
1. ifIndex of the port for which the violation is set
2. source of the violation, the feature or module
3. reason for the violation (sub reason under each source)."
INDEX { portViolationIfIndex, portViolationSource, portViolationReason }
::= { portViolationTable 1 }
PortViolationEntry ::= SEQUENCE {
portViolationIfIndex InterfaceIndex,
portViolationSource INTEGER,
portViolationReason INTEGER,
portViolationAction INTEGER,
portViolationTimer TimeTicks,
portViolationTimerAction INTEGER,
portViolationClearPort INTEGER,
portViolationCfgRecoveryMax Integer32,
portViolationCfgRetryTime Integer32,
portViolationRetryRemain Integer32
}
portViolationIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IfIndex of the port that has a violation."
::= { portViolationEntry 1 }
portViolationSource OBJECT-TYPE
SYNTAX INTEGER {
ag (1),
qos (2),
netsec (3),
udld (4),
nisup (5),
oam (6),
lfp(8),
lm(9),
lbd(10),
spb(11),
storm(12),
stormuucast(13),
lldp(14)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the source of the port violation.
The source is the feature or module that has
caused the violation. The list is given below
1. Initiated by Access Guardian
2. Initiated by QOS Policy
3. Initiated by Net Sec
4. Initiated by UDLD
5. Initiated by NI supervison (Fabric Stability).
6. initiated by OAM
8. initiated by LFP
9. initiated by Link Monitor
10. initiated by LBD
11. initiated by SPB
12. initiated by ESM
13. initiated by ESM
14. initiated by LLDP
When there is no value the value of this will be 0"
::= { portViolationEntry 2 }
portViolationReason OBJECT-TYPE
SYNTAX INTEGER {
pvSLLpsShutDown(1),
pvSLLpsRestrict(2),
pvQosPolicy(3),
pvQosSpoofed(4),
pvQosBpdu(5),
pvQosBgp(6),
pvQosOspf(7),
pvQosRip(8),
pvQosVrrp(9),
pvQosDhcp(10),
pvQosPim(11),
pvQosIsis(12),
pvQosDnsReply(13),
pvUdld(14),
pvOamRfp(15),
pvAgLpsDiscard(16),
pvLfpShutDown(17),
pvLmThreshold(18),
pvLbd(19),
pvQosDvmrp(20),
pvSpbRfp(21),
pvEsmStorm(22),
pvEsmStormUucast(23),
pvLldpShutDown(24),
pvRemoteLbd(25)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Reason for the port violation. This will be application
specific. The Reason indicate the violation for the 1st Violation
that happened on this port."
::= { portViolationEntry 3 }
portViolationAction OBJECT-TYPE
SYNTAX INTEGER {
portDown (1),
portAdminDown(2),
portTimerDown (3),
portTimerAdminDown (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The action determines on violation, what action will
taken. Either the port would be shutdown or Admin Down
or wait for the timer to expire and the timerAction
will determine what needs to be done. "
::= { portViolationEntry 4 }
portViolationTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If any timer is associated with the violation
This is Zero if no timer is associated."
::= { portViolationEntry 5 }
portViolationTimerAction OBJECT-TYPE
SYNTAX INTEGER {
portNoTimerAction(0),
portDownAfterTimer (1),
portUpAfterTimer(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Timer related action.
If set to portDownAfterTimer, no operation will be performed on
the port and the port will be shutdown after timer expiry.
If set to portUpAfterTimer the port will be shutdown immediately
and after the timer expiry the port will brought up.."
::= { portViolationEntry 6 }
portViolationClearPort OBJECT-TYPE
SYNTAX INTEGER {
inactive(0),
set(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"When this MIB object is set all violation on the
given port will be cleared. The Indices portViolationSource and
portViolationReason should be set to 0"
::= { portViolationEntry 7 }
portViolationCfgRecoveryMax OBJECT-TYPE
SYNTAX Integer32 (-1..50)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum attempts for auto-recovery as configured for the ifindex in alaPvrRecoveryMax.
Value 0 means auto recovery is disabled for this port.
Value -1 means auto recovery will retry infinitely.
"
::= { portViolationEntry 8 }
portViolationCfgRetryTime OBJECT-TYPE
SYNTAX Integer32 (30..600)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time (in seconds) between auto-recovery attempts as configured for the ifindex in alaPvrRetryTime.
"
::= { portViolationEntry 9 }
portViolationRetryRemain OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of remaining auto-recovery attempts.
Value -1 means there are infinite retries remaining.
"
::= { portViolationEntry 10 }
alaLinkMonConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlaLinkMonConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Link Monitoring Configuration Parameters"
::= { portViolations 2 }
alaLinkMonConfigEntry OBJECT-TYPE
SYNTAX AlaLinkMonConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of Link Monitoring configurations kept for a particular
Ethernet interface."
INDEX { ifIndex }
::= { alaLinkMonConfigTable 1 }
AlaLinkMonConfigEntry ::= SEQUENCE {
alaLinkMonStatus INTEGER,
alaLinkMonTimeWindow Integer32,
alaLinkMonLinkFlapThreshold Integer32,
alaLinkMonLinkErrorThreshold Integer32,
alaLinkMonWaitToRestoreTimer Integer32,
alaLinkMonWaitToShutdownTimer Integer32
}
alaLinkMonStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Allows the user to enable or disable Link Monitoring on the port."
DEFVAL { disable }
::= { alaLinkMonConfigEntry 1}
alaLinkMonTimeWindow OBJECT-TYPE
SYNTAX Integer32(10..3600)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the number of seconds the Link will be monitored for a port."
DEFVAL { 300 }
::= { alaLinkMonConfigEntry 2}
alaLinkMonLinkFlapThreshold OBJECT-TYPE
SYNTAX Integer32(2..10)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicaes the number of link flaps allowed for the specified port during the time window before the port is shutdown."
DEFVAL { 5 }
::= { alaLinkMonConfigEntry 3}
alaLinkMonLinkErrorThreshold OBJECT-TYPE
SYNTAX Integer32(1..100)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the number of link errors allowed on Rx for the specified port during the time window before the port is shutdown. The errors are the MAC errors that include CRC, lost frames, error frames, alignment frames."
DEFVAL { 5 }
::= { alaLinkMonConfigEntry 4 }
alaLinkMonWaitToRestoreTimer OBJECT-TYPE
SYNTAX Integer32(0..300)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the number of seconds after which the link up event is notified to other applications. The timer is started whenever a Link Up is detected on a port being monitored."
DEFVAL { 0 }
::= { alaLinkMonConfigEntry 5 }
alaLinkMonWaitToShutdownTimer OBJECT-TYPE
SYNTAX Integer32(0..3000)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the number of milli seconds after which the link down event is notified to other applications. The timer is started whenever a Link down is detected on a port being monitored."
DEFVAL { 0 }
::= { alaLinkMonConfigEntry 6 }
alaLinkMonStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlaLinkMonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Link Monitoring Statistics"
::= { portViolations 3 }
alaLinkMonStatsEntry OBJECT-TYPE
SYNTAX AlaLinkMonStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A collection of Link Monitoring statistics for a particular Ethernet interface."
INDEX { ifIndex }
::= { alaLinkMonStatsTable 1 }
AlaLinkMonStatsEntry ::= SEQUENCE {
alaLinkMonStatsClearStats INTEGER,
alaLinkMonStatsPortState INTEGER,
alaLinkMonStatsCurrentLinkFlaps Counter64,
alaLinkMonStatsCurrentErrorFrames Counter64,
alaLinkMonStatsCurrentCRCErrors Counter64,
alaLinkMonStatsCurrentLostFrames Counter64,
alaLinkMonStatsCurrentAlignErrors Counter64,
alaLinkMonStatsCurrentLinkErrors Counter64,
alaLinkMonStatsTotalLinkFlaps Counter64,
alaLinkMonStatsTotalLinkErrors Counter64
}
alaLinkMonStatsClearStats OBJECT-TYPE
SYNTAX INTEGER {
default(1),
reset(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Used to Clear all Statistics counters.
The value reset (1) indicates that Link Monitoring shuold all statistic counters related to the particular port.
By default, this object contains zero value."
DEFVAL {default}
::= { alaLinkMonStatsEntry 1 }
alaLinkMonStatsPortState OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
shutdown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of the port.
up(1) means the port is physically up,
down(2) means the port is physically down,
shutdown(3) means the interface is shutdown because of excessive link flaps or link errors."
::= { alaLinkMonStatsEntry 2 }
alaLinkMonStatsCurrentLinkFlaps OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of Link flaps in the current time window."
::= { alaLinkMonStatsEntry 3 }
alaLinkMonStatsCurrentErrorFrames OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of error frames in the current time window."
::= { alaLinkMonStatsEntry 4 }
alaLinkMonStatsCurrentCRCErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of CRC errors in the current time window."
::= { alaLinkMonStatsEntry 5 }
alaLinkMonStatsCurrentLostFrames OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of Rx Lost frames in the current time window."
::= { alaLinkMonStatsEntry 6 }
alaLinkMonStatsCurrentAlignErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of Rx alignment frames in the current time window."
::= { alaLinkMonStatsEntry 7 }
alaLinkMonStatsCurrentLinkErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the sum of all the MAC Errors within the current time window.
i.e., the sum of alaLinkMonStatsCurrentErrorFrames, alaLinkMonStatsCurrentCRCErrors,
alaLinkMonCurrentLosFrames, alaLinkMonStatsCurrentAlignErrors."
::= { alaLinkMonStatsEntry 8 }
alaLinkMonStatsTotalLinkFlaps OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the total number of link flaps across all the time windows."
::= { alaLinkMonStatsEntry 9 }
alaLinkMonStatsTotalLinkErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the total number of link errors across all the time windows."
::= { alaLinkMonStatsEntry 10 }
alaLFPGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlaLFPGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Link Fault Propagation Grooups and their status"
::= { portViolations 4 }
alaLFPGroupEntry OBJECT-TYPE
SYNTAX AlaLFPGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The list of Link Fault Propagation group id and status for each group"
INDEX { alaLFPGroupId }
::= { alaLFPGroupTable 1 }
AlaLFPGroupEntry ::= SEQUENCE
{
alaLFPGroupId Integer32,
alaLFPGroupAdminStatus INTEGER,
alaLFPGroupOperStatus INTEGER,
alaLFPGroupWaitToShutdown Integer32,
alaLFPGroupRowStatus RowStatus
}
alaLFPGroupId OBJECT-TYPE
SYNTAX Integer32(1 .. 8 )
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Indicates the unique group id for Link Fault Propagation (LFP)."
::= { alaLFPGroupEntry 1 }
alaLFPGroupAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the admin status of the group. disable(2) means link fault propagation,
is disbaled. enable(1) means link fault propagation is enabled"
DEFVAL { disable }
::= { alaLFPGroupEntry 2 }
alaLFPGroupOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the operational status of the group. down(2) means all the source ports are down,
up(1) means atleast one source port in the group is up."
::= { alaLFPGroupEntry 3 }
alaLFPGroupWaitToShutdown OBJECT-TYPE
SYNTAX Integer32(0 .. 300)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"0 - Disable wait to shutdown timer
5 - 300 - after expiry of this timer all destination ports will be shutdown"
DEFVAL { 0 }
::= { alaLFPGroupEntry 4 }
alaLFPGroupRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row Status for initiating a MIB retrieval request."
::= { alaLFPGroupEntry 5 }
alaLFPConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlaLFPConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Link Fault Propagation port and port type of each LFP group"
::= { portViolations 5 }
alaLFPConfigEntry OBJECT-TYPE
SYNTAX AlaLFPConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of Link Fault Propagation port and port type of each LFP group"
INDEX { alaLFPGroupId, alaLFPConfigPort }
::= { alaLFPConfigTable 1 }
AlaLFPConfigEntry ::= SEQUENCE {
alaLFPConfigPort InterfaceIndex,
alaLFPConfigPortType INTEGER,
alaLFPConfigRowStatus RowStatus
}
alaLFPConfigPort OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Indicates ifindex of source/destination port for a LFP Group."
::= { alaLFPConfigEntry 1 }
alaLFPConfigPortType OBJECT-TYPE
SYNTAX INTEGER {
destination (1),
source (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the type of port, (1) means the port is destination port and
(2) means the port is a destination port for a LFP Group."
::= { alaLFPConfigEntry 2 }
alaLFPConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row Status for initiating a MIB retrieval request."
::= { alaLFPConfigEntry 3 }
alaPvrGlobalConfigObjects OBJECT IDENTIFIER ::= { portViolations 6 }
alaPvrGlobalRecoveryMax OBJECT-TYPE
SYNTAX Integer32 (-1..50)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Auto violation recovery maximum attempts.
Value 0 means auto recovery is disabled for any ports using this global value.
Value -1 means auto recovery will retry infinitely for any ports using this global value.
"
DEFVAL { 10 }
::= { alaPvrGlobalConfigObjects 1 }
alaPvrGlobalRetryTime OBJECT-TYPE
SYNTAX Integer32 (30..600)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Time (in seconds) between auto violation recovery attempts for any ports using this global value."
DEFVAL { 300 }
::= { alaPvrGlobalConfigObjects 2 }
alaPvrGlobalTrapEnable OBJECT-TYPE
SYNTAX INTEGER { enable(1), disable(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Auto violation recovery global trap configuration"
DEFVAL { enable }
::= { alaPvrGlobalConfigObjects 3 }
alaPvrConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF AlaPvrConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of auto violation recovery configuration parameters"
::= { portViolations 7 }
alaPvrConfigEntry OBJECT-TYPE
SYNTAX AlaPvrConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Auto violation recovery configuration parameters"
INDEX { ifIndex }
::= { alaPvrConfigTable 1 }
AlaPvrConfigEntry ::= SEQUENCE {
alaPvrRecoveryMax Integer32,
alaPvrRetryTime Integer32
}
alaPvrRecoveryMax OBJECT-TYPE
SYNTAX Integer32 (-2..50)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Per port maximum auto violation recovery maximum attempts.
Value -2 means use value from alaPvrGlobalRecoveryMax
Value -1 means retry infinitely.
Value 0 means disable this port.
Values 1 to 50 mean 1 to 50 auto violation recovery attempts.
"
DEFVAL { -2 }
::= { alaPvrConfigEntry 1 }
alaPvrRetryTime OBJECT-TYPE
SYNTAX Integer32 (-2 | 30..600)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Per port time (in seconds) between auto violation recovery attempts.
Value -2 means use value from alaPvrGlobalRetryTime.
"
DEFVAL { -2 }
::= { alaPvrConfigEntry 2 }
alaPortViolationTrapObjects OBJECT IDENTIFIER ::= { portViolations 8 }
portViolationRecoveryReason OBJECT-TYPE
SYNTAX INTEGER {
unknown (1),
clearViolationCmd (2),
recoveryTimer (3),
adminUpDown (4),
nativeRecoveryTimer (5)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The reason for the recovery from port violation. It can be
none (1): none.
clearViolationCmd (2): Indicates that the port is recovered from
clear violation command.
recoveryTimer (3): Indicates that the port is recovered by
Recovery Timer mechanism.
adminUpDown (4): Indicates that the port is recovered from
admin Up/Down.
nativeRecoveryTimer (5): Indicates that the port is recovered
from the feature that shutdown the interface."
::= { alaPortViolationTrapObjects 1 }
--
-- Port Violation Traps
--
portViolationTrap NOTIFICATION-TYPE
OBJECTS {
ifIndex,
portViolationSource,
portViolationReason
}
STATUS current
DESCRIPTION
"A Trap will be generated when a port violation occurs. The port
violation trap will indicate the source of the violation and the
reason for the violation."
::= { alcatelIND1PortNotifications 7 }
portViolationNotificationTrap NOTIFICATION-TYPE
OBJECTS {
ifIndex,
portViolationRecoveryReason
}
STATUS current
DESCRIPTION
"A Trap will be generated when a port violation is cleared. This trap
will indicate the reason for the recovery from violation."
::= { alcatelIND1PortNotifications 8 }
-- Dying Gasp Trap
alaDyingGaspTrap NOTIFICATION-TYPE
OBJECTS {
alaDyingGaspChassisId,
alaDyingGaspPowerSupplyType,
alaDyingGaspTime
}
STATUS current
DESCRIPTION
"Dying Gasp trap."
::= { alcatelIND1PortNotifications 9 }
-- Storm Control trap
esmStormThresholdViolationStatus NOTIFICATION-TYPE
OBJECTS {
ifIndex,
esmStormViolationThresholdNotificationType,
esmStormViolationThresholdTrafficType
}
STATUS current
DESCRIPTION
"This object notifies management station if User-Port ports gets the ingress traffic inflow
above the configured value."
::= { alcatelIND1PortNotifications 10 }
-- TDR test Result Table
-- This table stores the result of TDR test conducted on the copper port(<slot,port>)
-- The object esmTdrPortTest can be used by the user to initiate the TDR test
-- All other objects are read only as length and states of the cable pairs can not be modified
esmTdrPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF EsmTdrPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table lists the results of cable diagnostics."
::= {physicalPort 8}
esmTdrPortEntry OBJECT-TYPE
SYNTAX EsmTdrPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry corresponding to each port."
INDEX { ifIndex }
::= { esmTdrPortTable 1 }
EsmTdrPortEntry ::= SEQUENCE {
esmTdrPortCableState CableState,
esmTdrPortValidPairs Unsigned32,
esmTdrPortPair1State CableState,
esmTdrPortPair1Length Unsigned32,
esmTdrPortPair2State CableState,
esmTdrPortPair2Length Unsigned32,
esmTdrPortPair3State CableState,
esmTdrPortPair3Length Unsigned32,
esmTdrPortPair4State CableState,
esmTdrPortPair4Length Unsigned32,
esmTdrPortFuzzLength Unsigned32,
esmTdrPortTest INTEGER,
esmTdrPortClearStats INTEGER,
esmTdrPortResult INTEGER
}
esmTdrPortCableState OBJECT-TYPE
SYNTAX CableState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"State of a cable as returned by the TDR test."
::= { esmTdrPortEntry 1 }
esmTdrPortValidPairs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of wire pairs in the cable for which the results of this test are valid."
::= { esmTdrPortEntry 2 }
esmTdrPortPair1State OBJECT-TYPE
SYNTAX CableState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state for wire pair-1 of the cable as returned by the TDR test."
::= { esmTdrPortEntry 3 }
esmTdrPortPair1Length OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length for wire pair-1 of the cable at which the fault is detected if the pair is faulty, complete length of the cable otherwise."
::= { esmTdrPortEntry 4 }
esmTdrPortPair2State OBJECT-TYPE
SYNTAX CableState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state for wire pair-2 of the cable as returned by the TDR test."
::= { esmTdrPortEntry 5 }
esmTdrPortPair2Length OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length for wire pair-2 of the cable at which the fault is detected if the pair is faulty, complete length of the cable otherwise."
::= { esmTdrPortEntry 6 }
esmTdrPortPair3State OBJECT-TYPE
SYNTAX CableState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state for wire pair-3 of the cable as returned by the TDR test."
::= { esmTdrPortEntry 7 }
esmTdrPortPair3Length OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length for wire pair-3 of the cable at which the fault is detected if the pair is faulty, complete length of the cable otherwise."
::= { esmTdrPortEntry 8 }
esmTdrPortPair4State OBJECT-TYPE
SYNTAX CableState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state for wire pair-4 of the cable as returned by the TDR test."
::= { esmTdrPortEntry 9 }
esmTdrPortPair4Length OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length for wire pair-4 of the cable at which the fault is detected if the pair is faulty, complete length of the cable otherwise."
::= { esmTdrPortEntry 10 }
esmTdrPortFuzzLength OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The error in the estimated length of the cable (as returned by TDR test)."
::= { esmTdrPortEntry 11 }
esmTdrPortTest OBJECT-TYPE
SYNTAX INTEGER{
off(1),
on(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Object used to start a TDR test on the port. When configured as on, it initiates a TDR test on the port. A read operation on this object always returns the value off."
::= { esmTdrPortEntry 12 }
esmTdrPortClearStats OBJECT-TYPE
SYNTAX INTEGER
{ default(1),
reset(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Used to Clear TDR stats.
By default, this object contains zero value."
::= { esmTdrPortEntry 13 }
esmTdrPortResult OBJECT-TYPE
SYNTAX INTEGER
{
success(1),
fail(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Used to give the status of BCM API,whether API able to execute TDR test successfully or failed to executethe TDR test."
::= { esmTdrPortEntry 14 }
-- ************************************************************************
-- Expansion of ifEntry
-- ************************************************************************
interfaceStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF InterfaceStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Expansion for ifEntry."
::= { interfaceCounters 1 }
interfaceStatsEntry OBJECT-TYPE
SYNTAX InterfaceStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry of interfaceStatsTable"
AUGMENTS { ifEntry }
::= { interfaceStatsTable 1 }
InterfaceStatsEntry ::= SEQUENCE {
inBitsPerSec Counter64,
outBitsPerSec Counter64,
ifInPauseFrames Counter64,
ifOutPauseFrames Counter64,
ifInPktsPerSec Counter64,
ifOutPktsPerSec Counter64
}
inBitsPerSec OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average number of Bits Received per second"
::= { interfaceStatsEntry 1 }
outBitsPerSec OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average number of Bits Transmitted per second"
::= { interfaceStatsEntry 2 }
ifInPauseFrames OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average number of Pause Frames Received per second"
::= { interfaceStatsEntry 3 }
ifOutPauseFrames OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average number of Pause Frames Transmitted per second"
::= { interfaceStatsEntry 4 }
ifInPktsPerSec OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average number of Packet Received per second"
::= { interfaceStatsEntry 5 }
ifOutPktsPerSec OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average number of Packets Transmitted per second"
::= { interfaceStatsEntry 6 }
-- End of TDR Table
-- This table holds the value of configured interface mode and
-- operaional port mode. This table holds value for each port cage.
esmPortModeTable OBJECT-TYPE
SYNTAX SEQUENCE OF EsmPortModeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of interface entries. This table contains
Configured Port mode and operational port mode"
::= { physicalPort 9 }
esmPortModeEntry OBJECT-TYPE
SYNTAX EsmPortModeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing additional management information
applicable to a particular interface with respect to port mode"
INDEX { ifIndex }
::= { esmPortModeTable 1 }
EsmPortModeEntry ::= SEQUENCE {
esmConfiguredMode
INTEGER,
esmOperationalMode
INTEGER
}
esmConfiguredMode OBJECT-TYPE
SYNTAX INTEGER {
mode40Gig(1), -- 40Gig mode
mode4X10Gig(2), -- 10Gig mode, 4 ports
modeAuto(3) -- 40G or 4X10G based on detection
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired mode of the interface. When a
managed system initializes, all interfaces start with
ifConfiguredMode in the Auto state.
User is not allowed to configure this parameter for subport"
DEFVAL { modeAuto }
::= { esmPortModeEntry 1 }
esmOperationalMode OBJECT-TYPE
SYNTAX INTEGER {
mode40Gig(1), -- 40Gig mode
mode4X10Gig(2) -- 10Gig mode, 4 ports
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Operational mode of the port "
::= { esmPortModeEntry 2 }
-- This table holds the value of configured interface beacon admin-state, Becon Led Color and
-- Beacon Led Mode. This table holds value for each port cage.
esmPortBeaconTable OBJECT-TYPE
SYNTAX SEQUENCE OF EsmPortBeaconEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of interface entries. This table contains
Beacon Admin State Beacon Led Color and Beacon Led mode"
::= { physicalPort 10 }
esmPortBeaconEntry OBJECT-TYPE
SYNTAX EsmPortBeaconEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing additional management information
applicable to a particular interface with respect to Beacon"
INDEX { ifIndex }
::= { esmPortBeaconTable 1 }
EsmPortBeaconEntry ::= SEQUENCE {
esmBeaconAdminState
INTEGER,
esmBeaconLedColor
INTEGER,
esmBeaconLedMode
INTEGER,
esmBeaconRowStatus
RowStatus
}
esmBeaconAdminState OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The beacon admin state of the interface. When a
managed system initializes, all interfaces start with
esmBeaconAdminState in disable state"
DEFVAL { disable }
::= { esmPortBeaconEntry 1 }
esmBeaconLedColor OBJECT-TYPE
SYNTAX INTEGER {
ledOff(1), -- Led in off state
ledBlue(2), -- Led in Blue state
ledGreen(3), -- Led in Green state
ledAqua(4), -- Led in Aqua state
ledRed(5), -- Led in Red state
ledMagenta(6), -- Led in Magenta state
ledYellow(7), -- Led in Yellow state
ledWhite(8) -- Led in White state
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" Beacon Led Color of the port "
DEFVAL { ledMagenta }
::= { esmPortBeaconEntry 2 }
esmBeaconLedMode OBJECT-TYPE
SYNTAX INTEGER {
ledModeSolid(1), -- Led mode solid
ledModeActivity(2) -- Led mode representing the normal mode operation
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" Beacon Led Mode of the port "
DEFVAL { ledModeActivity }
::= { esmPortBeaconEntry 3 }
esmBeaconRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row status to control creation/deletion of the Beacon"
::= { esmPortBeaconEntry 4 }
-- conformance information
alcatelIND1PortMIBCompliances OBJECT IDENTIFIER ::= { alcatelIND1PortMIBConformance 1 }
alcatelIND1PortMIBGroups OBJECT IDENTIFIER ::= { alcatelIND1PortMIBConformance 2 }
-- compliance statements
esmConfPortCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the configuration of Ethernet
ports."
MODULE -- this module
MANDATORY-GROUPS { esmConfMIBGroup,
esmDetectedConfMIBGroup,
alcPortNotificationGroup,
ddmInfoGroup,
ddmConfigGroup,
ddmNotificationsGroup,
esmConfTrapGroup,
esmHybridConfEntryGroup,
esmConfEntryGroup,
csmConfTrapGroup,
esmTdrPortGroup,
portViolationEntryGroup,
ddmPortInfoGroup,
alaLinkMonConfigMIBGroup,
alaLFPGroupMIBGroup,
alaPvrGlobalConfigGroup,
alaPvrConfigGroup,
interfaceStatsMIBGroup,
alaPortViolationTrapGroup
}
::= { alcatelIND1PortMIBCompliances 1 }
alcEtherStatsCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the Statistics of the Ethernet
ports."
MODULE -- this module
MANDATORY-GROUPS {
alaLinkMonStatsMIBGroup,
alaLFPConfigMIBGroup,
alcEtherStatsMIBGroup,
alcfcStatsGroup,
esmPortFiberstatsGroup
}
::= { alcatelIND1PortMIBCompliances 2 }
alcLagStatsCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the Statistics of the Link Aggregation
ports."
MODULE -- this module
MANDATORY-GROUPS {
alcLagStatsMIBGroup
}
::= { alcatelIND1PortMIBCompliances 3 }
-- units of conformance
esmConfMIBGroup OBJECT-GROUP
OBJECTS { esmPortCfgSpeed, esmPortCfgDuplexMode, esmPortCfgMaxFrameSize,
esmPortCfgAutoNegotiation, esmPortCfgCrossover, esmPortCfgPause,
esmPortBcastRateLimitEnable, esmPortBcastRateLimitType, esmPortBcastRateLimit,
esmPortMcastRateLimitEnable, esmPortMcastRateLimitType, esmPortMcastRateLimit,
esmPortUucastRateLimitEnable, esmPortUucastRateLimitType, esmPortUucastRateLimit,
esmPortIngressRateLimitEnable, esmPortIngressRateLimit, esmPortIngressRateLimitBurst,
esmPortEPPEnable, esmPortEEEEnable,esmPortBcastThresholdAction,esmPortMcastThresholdAction,
esmPortUucastThresholdAction,esmPortMinBcastRateLimit,esmPortMinMcastRateLimit,
esmPortMinUucastRateLimit,esmPortBcastStormState, esmPortMcastStormState, esmPortUucastStormState
}
STATUS current
DESCRIPTION
"A collection of objects to support the management of global
configuration parameters of the Ethernet ports."
::= { alcatelIND1PortMIBGroups 1 }
esmDetectedConfMIBGroup OBJECT-GROUP
OBJECTS { esmPortAutoSpeed, esmPortAutoDuplexMode
}
STATUS current
DESCRIPTION
"A collection of objects to support the Detected
configuration parameters of the Ethernet ports."
::= { alcatelIND1PortMIBGroups 2 }
alcEtherStatsMIBGroup OBJECT-GROUP
OBJECTS { alcetherClearStats, alcetherLastClearStats,
alcetherStatsCRCAlignErrors, alcetherStatsRxUndersizePkts,
alcetherStatsTxUndersizePkts, alcetherStatsTxOversizePkts,
alcetherStatsRxJabbers, alcetherStatsRxCollisions,
alcetherStatsTxCollisions, alcetherStatsPkts64Octets,
alcetherStatsPkts65to127Octets, alcetherStatsPkts128to255Octets,
alcetherStatsPkts256to511Octets,
alcetherStatsPkts512to1023Octets,
alcetherStatsPkts1024to1518Octets,
gigaEtherStatsPkts1519to4095Octets,
gigaEtherStatsPkts4096to9215Octets,
alcetherStatsPkts1519to2047Octets,
alcetherStatsPkts2048to4095Octets,
alcetherStatsPkts4096Octets,
alcetherStatsRxGiantPkts,
alcetherStatsRxDribbleNibblePkts,
alcetherStatsRxLongEventPkts,
alcetherStatsRxVlanTagPkts,
alcetherStatsRxControlPkts,
alcetherStatsRxLenChkErrPkts,
alcetherStatsRxCodeErrPkts,
alcetherStatsRxDvEventPkts,
alcetherStatsRxPrevPktDropped,
alcetherStatsTx64Octets,
alcetherStatsTx65to127Octets,
alcetherStatsTx128to255Octets,
alcetherStatsTx256to511Octets,
alcetherStatsTx512to1023Octets,
alcetherStatsTx1024to1518Octets,
alcetherStatsTx1519to2047Octets,
alcetherStatsTx2048to4095Octets,
alcetherStatsTx4096Octets,
alcetherStatsTxRetryCount,
alcetherStatsTxVlanTagPkts,
alcetherStatsTxControlPkts,
alcetherStatsTxLatePkts,
alcetherStatsTxTotalBytesOnWire,
alcetherStatsTxLenChkErrPkts,
alcetherStatsTxExcDeferPkts
}
STATUS current
DESCRIPTION
"A collection of objects to provide all the statistics related
to the Ethernet and GigaEthernert ports."
::= { alcatelIND1PortMIBGroups 3 }
alcPortNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
esmDrvTrapDropsLink,
portViolationTrap,
portViolationNotificationTrap,
alaDyingGaspTrap,
esmStormThresholdViolationStatus
}
STATUS current
DESCRIPTION
"The Port MIB Notification Group."
::= { alcatelIND1PortMIBGroups 4 }
ddmInfoGroup OBJECT-GROUP
OBJECTS {
ddmTemperature,
ddmTempLowWarning,
ddmTempLowAlarm,
ddmTempHiWarning,
ddmTempHiAlarm,
ddmSupplyVoltage,
ddmSupplyVoltageLowWarning,
ddmSupplyVoltageLowAlarm,
ddmSupplyVoltageHiWarning,
ddmSupplyVoltageHiAlarm,
ddmTxBiasCurrent,
ddmTxBiasCurrentLowWarning,
ddmTxBiasCurrentLowAlarm,
ddmTxBiasCurrentHiWarning,
ddmTxBiasCurrentHiAlarm,
ddmTxOutputPower,
ddmTxOutputPowerLowWarning,
ddmTxOutputPowerLowAlarm,
ddmTxOutputPowerHiWarning,
ddmTxOutputPowerHiAlarm,
ddmRxOpticalPower,
ddmRxOpticalPowerLowWarning,
ddmRxOpticalPowerLowAlarm,
ddmRxOpticalPowerHiWarning,
ddmRxOpticalPowerHiAlarm,
ddmPortChannel
}
STATUS current
DESCRIPTION
"A collection of objects to provide digital diagnostics information
related to SFPs, XFPs, and SFP+s."
::= { alcatelIND1PortMIBGroups 6 }
ddmConfigGroup OBJECT-GROUP
OBJECTS {
ddmConfig,
ddmTrapConfig,
ddmNotificationType
}
STATUS current
DESCRIPTION
"A collection of objects to allow configuration of DDM and DDM traps."
::= { alcatelIND1PortMIBGroups 7 }
ddmNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
ddmTemperatureThresholdViolated,
ddmVoltageThresholdViolated,
ddmCurrentThresholdViolated,
ddmTxPowerThresholdViolated,
ddmRxPowerThresholdViolated
}
STATUS current
DESCRIPTION
"A collection of notifications used to indicate DDM threshold violations."
::= { alcatelIND1PortMIBGroups 8 }
esmConfTrapGroup OBJECT-GROUP
OBJECTS {
esmDrvTrapDrops,
alaDyingGaspChassisId,
alaDyingGaspPowerSupplyType,
alaDyingGaspTime,
esmStormViolationThresholdNotificationType,
esmStormViolationThresholdTrafficType
}
STATUS current
DESCRIPTION
"Partitioned port (separated due to errors)."
::= { alcatelIND1PortMIBGroups 9 }
esmHybridConfEntryGroup OBJECT-GROUP
OBJECTS {
esmHybridPortCfgSpeed,
esmHybridPortCfgDuplexMode,
esmHybridPortCfgAutoNegotiation,
esmHybridPortCfgCrossover,
esmHybridPortCfgFlow,
esmHybridPortCfgInactiveType
}
STATUS current
DESCRIPTION
"A list of inactive hybrid port instances."
::= { alcatelIND1PortMIBGroups 10 }
esmConfEntryGroup OBJECT-GROUP
OBJECTS {
esmPortAdminStatus,
esmPortAlias,
esmPortCfgHybridActiveType,
esmPortCfgHybridMode,
esmPortIF,
esmPortLinkUpDownTrapEnable,
esmPortOperationalHybridType,
esmPortSlot
}
STATUS current
DESCRIPTION
"A list of ESM Physical Port instances."
::= { alcatelIND1PortMIBGroups 11 }
portViolationEntryGroup OBJECT-GROUP
OBJECTS {
portViolationAction,
portViolationTimer,
portViolationTimerAction,
portViolationClearPort,
portViolationCfgRecoveryMax,
portViolationCfgRetryTime,
portViolationRetryRemain
}
STATUS current
DESCRIPTION
"This table contains the port Violations per port."
::= { alcatelIND1PortMIBGroups 12 }
ddmPortInfoGroup OBJECT-GROUP
OBJECTS {
ddmPortTemperature,
ddmPortTempLowWarning,
ddmPortTempLowAlarm,
ddmPortTempHiWarning,
ddmPortTempHiAlarm,
ddmPortSupplyVoltage,
ddmPortSupplyVoltageLowWarning,
ddmPortSupplyVoltageLowAlarm,
ddmPortSupplyVoltageHiWarning,
ddmPortSupplyVoltageHiAlarm,
ddmPortTxBiasCurrent,
ddmPortTxBiasCurrentLowWarning,
ddmPortTxBiasCurrentLowAlarm,
ddmPortTxBiasCurrentHiWarning,
ddmPortTxBiasCurrentHiAlarm,
ddmPortTxOutputPower,
ddmPortTxOutputPowerLowWarning,
ddmPortTxOutputPowerLowAlarm,
ddmPortTxOutputPowerHiWarning,
ddmPortTxOutputPowerHiAlarm,
ddmPortRxOpticalPower,
ddmPortRxOpticalPowerLowWarning,
ddmPortRxOpticalPowerLowAlarm,
ddmPortRxOpticalPowerHiWarning,
ddmPortRxOpticalPowerHiAlarm
}
STATUS current
DESCRIPTION
"A collection of objects to provide digital diagnostics information
related to SFPs, XFPs, and SFP+s."
::= { alcatelIND1PortMIBGroups 13 }
alaLinkMonConfigMIBGroup OBJECT-GROUP
OBJECTS {
alaLinkMonStatus,
alaLinkMonTimeWindow,
alaLinkMonLinkFlapThreshold,
alaLinkMonLinkErrorThreshold,
alaLinkMonWaitToRestoreTimer,
alaLinkMonWaitToShutdownTimer
}
STATUS current
DESCRIPTION
"A collection of objects to support the Link Monitoring Configurations on the ports."
::= { alcatelIND1PortMIBGroups 14 }
alaLinkMonStatsMIBGroup OBJECT-GROUP
OBJECTS {
alaLinkMonStatsClearStats,
alaLinkMonStatsPortState,
alaLinkMonStatsCurrentLinkFlaps,
alaLinkMonStatsCurrentErrorFrames,
alaLinkMonStatsCurrentCRCErrors,
alaLinkMonStatsCurrentLostFrames,
alaLinkMonStatsCurrentAlignErrors,
alaLinkMonStatsCurrentLinkErrors,
alaLinkMonStatsTotalLinkFlaps,
alaLinkMonStatsTotalLinkErrors
}
STATUS current
DESCRIPTION
"A collection of objects to provide all the statistics related
to the Link Monitoring on the ports."
::= { alcatelIND1PortMIBGroups 15 }
alaLFPGroupMIBGroup OBJECT-GROUP
OBJECTS {
alaLFPGroupId,
alaLFPGroupAdminStatus,
alaLFPGroupOperStatus,
alaLFPGroupWaitToShutdown,
alaLFPGroupRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects to configure Link Fault Propagation Group,
Wait to shutdown timer and admin staus of group."
::= { alcatelIND1PortMIBGroups 16 }
alaLFPConfigMIBGroup OBJECT-GROUP
OBJECTS {
alaLFPConfigPort,
alaLFPConfigPortType,
alaLFPConfigRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects to configure a port and port type for a Link Fault Propagation Group."
::= { alcatelIND1PortMIBGroups 17 }
csmConfTrapGroup OBJECT-GROUP
OBJECTS {
alaDyingGaspChassisId,
alaDyingGaspPowerSupplyType,
alaDyingGaspTime
}
STATUS current
DESCRIPTION
"A collection of objects for chassis supervision traps"
::= { alcatelIND1PortMIBGroups 18 }
esmTdrPortGroup OBJECT-GROUP
OBJECTS {
esmTdrPortCableState,
esmTdrPortValidPairs,
esmTdrPortPair1State,
esmTdrPortPair1Length,
esmTdrPortPair2State,
esmTdrPortPair2Length,
esmTdrPortPair3State,
esmTdrPortPair3Length,
esmTdrPortPair4State,
esmTdrPortPair4Length,
esmTdrPortFuzzLength,
esmTdrPortTest,
esmTdrPortClearStats,
esmTdrPortResult
}
STATUS current
DESCRIPTION
"A collection of objects to provide TDR information"
::= { alcatelIND1PortMIBGroups 19 }
alcfcStatsGroup OBJECT-GROUP
OBJECTS {
alcfcClearStats,
alcfcLastClearStats,
alcfcStatsDelimiterErrors,
alcfcStatsEncodingDisparityErrors,
alcfcStatsFrameTooLongs,
alcfcStatsInvalidCRCs,
alcfcStatsInvalidOrderedSets,
alcfcStatsInvalidTxWords,
alcfcStatsLinkFailures,
alcfcStatsLossofSignals,
alcfcStatsRxUndersizePkts,
alcfcStatsTxBBCreditZeros,
alcfcStatsLossofSynchs,
alcfcStatsOtherErrors,
alcfcStatsPrimSeqProtocolErrors,
alcfcStatsRxBBCreditZeros
}
STATUS current
DESCRIPTION
"A collection of objects for chassis supervision traps"
::= { alcatelIND1PortMIBGroups 20 }
esmPortFiberstatsGroup OBJECT-GROUP
OBJECTS {
esmPortIsFiberChannelCapable
}
STATUS current
DESCRIPTION
"A collection of objects for chassis supervision traps"
::= { alcatelIND1PortMIBGroups 21 }
alaPvrGlobalConfigGroup OBJECT-GROUP
OBJECTS {
alaPvrGlobalRecoveryMax,
alaPvrGlobalRetryTime,
alaPvrGlobalTrapEnable
}
STATUS current
DESCRIPTION
"A collection of global pvr objects"
::= { alcatelIND1PortMIBGroups 22 }
esmPortModeGroup OBJECT-GROUP
OBJECTS {
esmConfiguredMode,
esmOperationalMode
}
STATUS current
DESCRIPTION
"A collection of objects for port splitter mode"
::= { alcatelIND1PortMIBGroups 23 }
esmPortBeaconGroup OBJECT-GROUP
OBJECTS {
esmBeaconAdminState,
esmBeaconLedColor,
esmBeaconLedMode,
esmBeaconRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects for port Beacon "
::= { alcatelIND1PortMIBGroups 24 }
alaPvrConfigGroup OBJECT-GROUP
OBJECTS {
alaPvrRecoveryMax,
alaPvrRetryTime
}
STATUS current
DESCRIPTION
"A collection of pvr objects"
::= { alcatelIND1PortMIBGroups 25 }
interfaceStatsMIBGroup OBJECT-GROUP
OBJECTS {
inBitsPerSec,
outBitsPerSec,
ifInPauseFrames,
ifOutPauseFrames,
ifInPktsPerSec,
ifOutPktsPerSec
}
STATUS current
DESCRIPTION
"A collection of objects to display the interface counters details of the ports"
::= { alcatelIND1PortMIBGroups 26 }
alaPortViolationTrapGroup OBJECT-GROUP
OBJECTS {
portViolationRecoveryReason
}
STATUS current
DESCRIPTION
"A collection of global pvr objects"
::= { alcatelIND1PortMIBGroups 27 }
alcLagStatsMIBGroup OBJECT-GROUP
OBJECTS {
alcLagClearStats
}
STATUS current
DESCRIPTION
"A collection of link aggregation objects"
::= { alcatelIND1PortMIBGroups 28 }
END