tasafo/palestras-coletivas

A method with Too Many Statements is any method that has a large number of lines.

Too Many Statements warns about any method that has more than 5 statements. Reek's smell detector for Too Many Statements counts +1 for every simple statement in a method and +1 for every statement within a control structure (if, else, case, when, for, while, until, begin, rescue) but it doesn't count the control structure itself.

So the following method would score +6 in Reek's statement-counting algorithm:

def parse(arg, argv, &error)
  if !(val = arg) and (argv.empty? or /\A-/ =~ (val = argv[0]))
    return nil, block, nil                                         # +1
  end
  opt = (val = parse_arg(val, &error))[1]                          # +2
  val = conv_arg(*val)                                             # +3
  if opt and !arg
    argv.shift                                                     # +4
  else
    val[0] = nil                                                   # +5
  end
  val                                                              # +6
end

(You might argue that the two assigments within the first @if@ should count as statements, and that perhaps the nested assignment should count as +2.)

Too Many Instance Variables is a special case of LargeClass.

Example

Given this configuration

TooManyInstanceVariables:
  max_instance_variables: 3

and this code:

class TooManyInstanceVariables
  def initialize
    @arg_1 = :dummy
    @arg_2 = :dummy
    @arg_3 = :dummy
    @arg_4 = :dummy
  end
end

Reek would emit the following warning:

test.rb -- 5 warnings:
  [1]:TooManyInstanceVariables has at least 4 instance variables (TooManyInstanceVariables)

A method with Too Many Statements is any method that has a large number of lines.

Too Many Statements warns about any method that has more than 5 statements. Reek's smell detector for Too Many Statements counts +1 for every simple statement in a method and +1 for every statement within a control structure (if, else, case, when, for, while, until, begin, rescue) but it doesn't count the control structure itself.

So the following method would score +6 in Reek's statement-counting algorithm:

def parse(arg, argv, &error)
  if !(val = arg) and (argv.empty? or /\A-/ =~ (val = argv[0]))
    return nil, block, nil                                         # +1
  end
  opt = (val = parse_arg(val, &error))[1]                          # +2
  val = conv_arg(*val)                                             # +3
  if opt and !arg
    argv.shift                                                     # +4
  else
    val[0] = nil                                                   # +5
  end
  val                                                              # +6
end

(You might argue that the two assigments within the first @if@ should count as statements, and that perhaps the nested assignment should count as +2.)

Duplicated Code

Duplicated code can lead to software that is hard to understand and difficult to change. The Don't Repeat Yourself (DRY) principle states:

Every piece of knowledge must have a single, unambiguous, authoritative representation within a system.

When you violate DRY, bugs and maintenance problems are sure to follow. Duplicated code has a tendency to both continue to replicate and also to diverge (leaving bugs as two similar implementations differ in subtle ways).

Tuning

This issue has a mass of 43.

We set useful threshold defaults for the languages we support but you may want to adjust these settings based on your project guidelines.

The threshold configuration represents the minimum mass a code block must have to be analyzed for duplication. The lower the threshold, the more fine-grained the comparison.

If the engine is too easily reporting duplication, try raising the threshold. If you suspect that the engine isn't catching enough duplication, try lowering the threshold. The best setting tends to differ from language to language.

See codeclimate-duplication's documentation for more information about tuning the mass threshold in your .codeclimate.yml.

Refactorings

• Extract Method
• Extract Class
• Form Template Method
• Introduce Null Object
• Pull Up Method
• Pull Up Field
• Substitute Algorithm

Further Reading

• Don't Repeat Yourself on the C2 Wiki
• Duplicated Code on SourceMaking
• Refactoring: Improving the Design of Existing Code by Martin Fowler. Duplicated Code, p76