File ext.uls.interface.js
has 468 lines of code (exceeds 250 allowed). Consider refactoring. Open
/*!
* ULS interface integration logic
*
* Copyright (C) 2012-2013 Alolita Sharma, Amir Aharoni, Arun Ganesh, Brandon Harris,
* Niklas Laxström, Pau Giner, Santhosh Thottingal, Siebrand Mazeland and other
Function initPersonalEntryPoint
has 69 lines of code (exceeds 25 allowed). Consider refactoring. Open
function initPersonalEntryPoint() {
var $trigger = $( '.uls-trigger' );
var clickHandler;
if ( !userCanChangeLanguage() ) {
Function showUndoTooltip
has 68 lines of code (exceeds 25 allowed). Consider refactoring. Open
function showUndoTooltip( previousLang, previousAutonym ) {
var trigger, popup, popupPosition,
configPosition = mw.config.get( 'wgULSPosition' ),
triggerSelector = ( configPosition === 'interlanguage' ) ?
'.uls-settings-trigger, .mw-interlanguage-selector' :
Function initInterlanguageEntryPoint
has 47 lines of code (exceeds 25 allowed). Consider refactoring. Open
function initInterlanguageEntryPoint() {
var $pLang = $( '#p-lang' );
var $trigger = $( '<button>' )
.addClass( 'uls-settings-trigger' )
Function addEmptyState
has 41 lines of code (exceeds 25 allowed). Consider refactoring. Open
function addEmptyState( uls ) {
var $emptyStateContainer = $( '<section>' ).addClass( 'uls-empty-state' );
function openActionsMenuEventHandler( event ) {
event.stopPropagation();
Function clickHandler
has 36 lines of code (exceeds 25 allowed). Consider refactoring. Open
var clickHandler = function ( e ) {
var languagesettings = $trigger.data( 'languagesettings' ),
languageSettingsOptions;
if ( languagesettings ) {
Function addActionsMenuTriggers
has 33 lines of code (exceeds 25 allowed). Consider refactoring. Open
function addActionsMenuTriggers( uls ) {
var $ulsSettingsBlock = addLanguageSettingsTrigger( uls );
var actionItemsRegistry = mw.uls.ActionsMenuItemsRegistry;
actionItemsRegistry.on( 'register', onActionItemAdded );
Function loadContentLanguageSelector
has 29 lines of code (exceeds 25 allowed). Consider refactoring. Open
function loadContentLanguageSelector( ev ) {
var $target = $( ev.currentTarget );
// Avoid reinitializing ULS multiple times for an element
if ( $target.attr( 'data-uls-loaded' ) ) {
Function addLanguageSettingsToNonContentPages
has 29 lines of code (exceeds 25 allowed). Consider refactoring. Open
function addLanguageSettingsToNonContentPages() {
var $languageBtn = $( '#p-lang-btn' );
var clickHandler = function ( event ) {
event.stopPropagation();
mw.loader.using( languageSettingsModules ).then( function () {
Similar blocks of code found in 2 locations. Consider refactoring. Open
if ( offset.left + ( width / 2 ) > $( window ).width() / 2 ) {
// Midpoint of the trigger is on the right side of the viewport.
positionCSS = {
// Right dialog edge aligns with right edge of the trigger.
right: $( window ).width() - ( offset.left + width ),
- Read upRead up
Duplicated Code
Duplicated code can lead to software that is hard to understand and difficult to change. The Don't Repeat Yourself (DRY) principle states:
Every piece of knowledge must have a single, unambiguous, authoritative representation within a system.
When you violate DRY, bugs and maintenance problems are sure to follow. Duplicated code has a tendency to both continue to replicate and also to diverge (leaving bugs as two similar implementations differ in subtle ways).
Tuning
This issue has a mass of 129.
We set useful threshold defaults for the languages we support but you may want to adjust these settings based on your project guidelines.
The threshold configuration represents the minimum mass a code block must have to be analyzed for duplication. The lower the threshold, the more fine-grained the comparison.
If the engine is too easily reporting duplication, try raising the threshold. If you suspect that the engine isn't catching enough duplication, try lowering the threshold. The best setting tends to differ from language to language.
See codeclimate-duplication
's documentation for more information about tuning the mass threshold in your .codeclimate.yml
.
Refactorings
- Extract Method
- Extract Class
- Form Template Method
- Introduce Null Object
- Pull Up Method
- Pull Up Field
- Substitute Algorithm
Further Reading
- Don't Repeat Yourself on the C2 Wiki
- Duplicated Code on SourceMaking
- Refactoring: Improving the Design of Existing Code by Martin Fowler. Duplicated Code, p76